Winprt 4B-WF Bar Code Printer

Arahan Penggunaan Produk

• Press the switches on the left and right sides of the upper cover to open it.
• Hold the upper cover with one hand and rotate it to the left to open it.
• Place the printer on a stable surface and ensure the power is turned off.
• Function of the key: Form feed – When the printer is in standby state, press the paper button once.

produk View

Perhatian

• The interface and appearance of the printer may depend on the type of model you purchased.
• Please refer to the actual interface and appearance or contact the supplier.

Senarai Pembungkusan

Nombor siri	Nama	Kuantiti
1	Pencetak	1
2	Penyesuai kuasa	1
3	Talian kuasa	1
4	Penggelek tong kertas	1
5	Papan pengawal selia tong kertas	2
6	Penggelek pita karbon	2
7	Jalur karbon berasaskan lilin campuran	1
8	Adhesive sticker-coated paper	1
9	Teras kosong empat inci	1
10	Manual pengguna	1
11	Kabel USB	1

Pemasangan mesin

1. Sila letakkan pencetak pada permukaan yang stabil dan sahkan bahawa kuasa dimatikan.
2. Connect the connectors at both ends of the USB data cable to the printer and computer host, respectively.
3. Plug the power cord into the power socket at the back of the printer and plug the other end into the AC socket.

Mounting paper

1. Press the switches on the left and right sides of the upper cover with Both hands to open the printer’s upper cover.
2. Load the paper roll into the label supply shaft and secure the paper roll to the center of the supply shaft using a paper roll fixing piece.
3. Place the paper roll on the paper bin（, If you are using a 4-inch wide paper roll, you can remove the fixing piece. Directly use the paper roll）
4. Tekan suis kepala cetak untuk menghidupkan kepala cetak.
5. Pull out the front end of the paper (printing side up)，After passing through the paper guide and the paper sensor, insert the paper. Pull over the rubber roller, adjust the paper guide to be the same width as the paper and slightly touch it.
6. Press down with both hands at the arrow in the figure below to close the print head. Please confirm that the print head is fully closed to ensure printing quality.

Carbon belt installation

1. Hold the upper cover with one hand and rotate it to the left to open the printer’s upper cover.
2. Insert the empty paper roll into the carbon belt recycling shaft.
3. Press the left side (hexagonal end) of the recycling shaft into the carbon belt recycling wheel, and then install the right side.
4. Tekan suis kepala cetak untuk menghidupkan kepala cetak.
5. Masukkan tali pinggang karbon ke dalam aci bekalan tali pinggang karbon.
6. Press the left side (hexagonal end) of the supply shaft into the carbon belt supply wheel, and then install the right side.
7. The carbon tape bypasses the print head and is smoothly glued to the carbon tape recovery shaft (empty paper roll)
8. Rotate the carbon belt recycling wheel in the direction of the arrow in the following figure until the black area of the carbon belt covers the print head. Tighten the carbon tape until there are no wrinkles on it.
9. Press down with both hands at the arrow in the figure below to close the print head. Please confirm the print head is completely closed to ensure printing quality.

General key function

1. Fungsi kunci
   1. Formfeed
      When the printer is in standby state, press the paper button once to automatically feed a label.
2. jeda
   When the printer is printing, press the paper walking button to pause the printing operation. At this time, the power indicator is flashing blue.
   Press the paper walking button again and the printing operation will continue.
3. Halaman semak sendiri
   When the printer is off, press the paper button and turn it on until the red light and blue light flash for 3 times and then let go.
4. Kertas pembetulan
   Press and hold the button on the cover to turn on the printer after placing the paper. Wait until the red light flashes three times before letting go.
5. Mulakan pencetak
   Turn off the printer and press the button on the cover before turning it on.
   Wait until the blue light flashes three times before releasing.

Penerangan Penunjuk LED

Status penunjuk LED	menggambarkan
Lampu merah fl ashing	Pencetak kehabisan kertas
Lampu merah sentiasa menyala	Printer overheating \ Printer cover opening
Cahaya biru fl ashing	Printer Pause
Lampu biru sentiasa menyala	The printer is powered on and in a normal printing state

Penyingkiran masalah

• The following table is a list of common problems the average operator has and how to solve them.
• If you have followed our suggestions to troubleshoot the situation and the printer still does not function properly, please contact the customer service department of the business you purchased from for more assistance.

soalan	Possible element	Penyelesaian
Penunjuk kuasa tidak berubah	The AC socket plug and the power supply plug are not properly connected to the printer socket	Periksa penyambung kuasa dan sahkan bahawa soket AC dan palam bekalan kuasa disambungkan dengan betul ke pencetak
	The printer power switch is not on	Hidupkan suis kuasa
Penunjuk pencetak berkelip merah	Print head seat is not closed	Please close the print head stand
	Label run out Laluan pemasangan label tidak betul The gap sensor is not detected correctly	Install new labels. For details, see the steps for installing labels     Readjust the specs and print
	There may be label paper stuck inside the printer	Clean the inside of the printer
Masalah lipatan	Uneven print head pressure Labels are incorrectly installed Kepekatan cetakan tidak betul The label paper is not inserted correctly	Please set the appropriate label for printing concentration   Please adjust the label width adjuster make it fit the label width

Kualiti cetakan tidak bagus	Labels are incorrectly installed Dust or adhesive on the print head accumulation Print concentration is set improperly Print head damage	Reinstall the consumables Clean print head Clean the rubber roller Adjust the printer printing concentration and printing speed Print out the self-test value, check the judgment yes If no, the print head is damaged The head is damaged, please return to the factory to replace the print head Gantikan kertas label yang sesuai
		If the thickness of the label exceeds 0.22mm, the print quality may deteriorate. Make sure that the print head mount is fully closed
Which occurs when printing situation	Tetapan saiz label tidak betul atau tidak lengkap The label sensor is covered by a foreign body, causing incorrect detection	Readjust the specs and print. Moderately reduce the gap value and print Remove foreign objects between sensors
Kandungan cetakan kiri dan kanan tiada	Label size setting is incorrect The maximum print width terlampau	Set the correct label size Use a roll within the maximum width
Kertas label hitam kelihatan garis kelabu	There is dirt on the print head The rubber roller is dirty	Clean tphreinrtuhbebaedr roller
Tidak dapat mencetak kandungan atau mencetak kandungan yang salah	The printer is in Hex Dump mode The serial port communication (RS-232) is incorrectly set	Turn the printer back on and exit the Hex Dump mode Reset the printer and computer baud rate to be consistent

Penyelenggaraan dan penyelenggaraan harian

1. When the printer appears in the following situation, clean the print head and cots
   1. Cetakan tidak jelas
   2. Big noise in and out of the paper
   3. There are foreign bodies stuck on the printing head
2. The printing head/cots should be cleaned 3-5 minutes after the printing is finished. The steps are as follows:
   1. Turn off the printer power supply and open the top cover.
   2. Wipe the dust on the surface of the printing head/cots with a wrung alcohol cotton ball;
3. After 5-10 minutes, start printing after the alcohol is completely volatilized.

Syor: Clean print heads, cots, and sensors regularly according to the above steps.

Beri perhatian:

• Do not touch the print head directly with your hands.
• Please use medicinal alcohol to clean the print head. Do not use Industrial alcohol to avoid damage to the print head.
• If the printer experiences frequent error messages, try cleaning the printer’s sensor.

PENYATA FCC

Sebarang Perubahan atau pengubahsuaian yang tidak diluluskan secara nyata oleh pihak yang bertanggungjawab untuk pematuhan boleh membatalkan kuasa pengguna untuk mengendalikan peralatan.
Nota: Peranti ini mematuhi Bahagian 15 Peraturan FCC. Operasi tertakluk kepada dua syarat berikut:

1. Peranti ini mungkin tidak menyebabkan gangguan berbahaya, dan
2. Peranti ini mesti menerima sebarang gangguan yang diterima, termasuk gangguan yang boleh menyebabkan operasi yang tidak diingini.

Had ini direka bentuk untuk memberikan perlindungan yang munasabah terhadap gangguan berbahaya dalam pemasangan kediaman. Peralatan ini menjana kegunaan dan boleh memancarkan tenaga frekuensi radio dan, jika tidak dipasang dan digunakan mengikut arahan, boleh menyebabkan gangguan berbahaya kepada komunikasi radio. Walau bagaimanapun, tiada jaminan bahawa gangguan tidak akan berlaku dalam pemasangan tertentu. Jika peralatan ini menyebabkan gangguan berbahaya kepada penerimaan radio atau televisyen, yang boleh ditentukan dengan mematikan dan menghidupkan peralatan, pengguna digalakkan untuk cuba membetulkan gangguan dengan satu atau lebih daripada langkah berikut:

• Arahkan semula atau letakkan semula antena penerima.
• Tingkatkan pemisahan antara peralatan dan penerima.
• Sambungkan peralatan ke dalam alur keluar pada litar yang berbeza daripada yang disambungkan kepada penerima.
• Rujuk pengedar atau juruteknik radio/TV yang berpengalaman untuk mendapatkan bantuan.

Peranti telah dinilai untuk memenuhi keperluan pendedahan RF am
Peralatan ini mematuhi had pendedahan sinaran FCC yang ditetapkan untuk persekitaran yang tidak terkawal. Peralatan ini hendaklah dipasang dan dikendalikan dengan jarak minimum 20cm antara radiator & badan anda.

Soalan Lazim

S: Apakah yang perlu saya lakukan jika pencetak tidak dihidupkan?

A: Check the power supply connection and ensure the power switch is turned on. If the issue persists, contact customer support.

Dokumen / Sumber

Winprt 4B-WF Bar Code Printer [pdf] Manual Pengguna 2BHCJ-4B-WF, 4B-WF Bar Code Printer, 4B-WF, Bar Code Printer, Code Printer

Rujukan

• Manual Pengguna