THIRD REALITY ZB2 Smart Button User Manual

Smart Button ZB2
Panduan Mula Pantas

Kandungan Pakej

Spesifikasi

Tetapan Semula Kilang

Press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.

Setting up your Smart Button ZB2

1. Follow instructions to set up your compatible Zigbee hub.
2. Use the Micro-USB charging cable included in the package to connect the button to a power adapter (not included) to active the Smart Button ZB2.
3. You can also press and hold buttons 1 and 2 for 10 seconds, the Smart Button ZB2 will be activated once it beeps three times. The device will automatically enter pairing mode.
   Note: It will exit pairing mode automatically if not successfully paired within 3 minutes, to put it into pairing mode again, press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.
4. After the pairing is completed, the device will beep once. you can create routines in the corresponding smart home App or platform to control other connected devices. THIRDREALITY Smart Button ZB2 features three buttons (button 1 & button 2 & button  3), each supporting three control settings: Pressed, Double Pressed and Held. Note: When charging, please connect the button to a power adapter (not included) using the Micro-USB charging cable provided in the package. The Smart Button ZB2 will be fully charged until it beep twice.

Imbas kod QR ke view butiran

https://bit.ly/488mkj9

Menyelesaikan masalah

1. How to check if the device is fully charged
   The Smart Button ZB2 will be fully charged until it beep twice.
2. Peranti tidak akan dihidupkan
   Recharge the battery, ensure it powers on properly, and note that low temperatures may reduce performance.
3. Cannot charge / No charging response
   Use the original charger, check the charging port, and wait a few minutes in case of over-discharge protection.

Pematuhan Kawal Selia FCC
Peranti ini mematuhi bahagian 15 Peraturan FCC. Pengendalian tertakluk kepada dua syarat berikut: (1) Peranti ini mungkin tidak menyebabkan gangguan berbahaya, dan (2) peranti ini mesti menerima sebarang gangguan yang diterima, termasuk gangguan yang boleh menyebabkan operasi yang tidak diingini.
Sebarang perubahan atau pengubahsuaian yang tidak diluluskan secara nyata oleh pihak yang bertanggungjawab untuk pematuhan boleh membatalkan kuasa pengguna untuk mengendalikan peralatan.
Nota: Peralatan ini telah diuji dan didapati mematuhi had untuk peranti digital Kelas B, menurut bahagian 15 Peraturan FCC.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the  instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by  turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Arahkan semula atau letak semula antena penerima.
– Tingkatkan pemisahan antara peralatan dan penerima.
– Sambungkan peralatan ke dalam alur keluar pada litar yang berbeza daripada litar yang disambungkan kepada penerima.
– Rujuk pengedar atau juruteknik radio/TV yang berpengalaman untuk mendapatkan bantuan.
The device has been evaluated to meet general RF exposure requirement. The device can be used in the exposure condition without restriction. 06

Untuk waranti terhad, sila layari
https://thirdreality.com/faq-help-center/
Untuk sokongan pelanggan, sila hubungi kami di
info@3reality.com atau melawat www.thirdreality.com
Untuk soalan mengenai platform lain, lawati yang sepadan
platform’s application/support platform.