Manual Pemilik Unit Pengkomputeran Tepi Pintar M5STACK C6L

Manual Pemilik Unit Pengkomputeran Tepi Pintar M5STACK C6L
DOMUS LINE EASI DISK Driver D Manual Pengguna Cakera Kawalan Pergerakan

1. GARIS

Unit C6L is an intelligent edge computing unit integrated with the M5Stack_Lora_C6module — featuring an Espressif ESP32-C6 SoC and Semtech SX1262 LoRa transceiver — and engineered with a modular design for long-range, low-power LoRaWAN communication alongside high-speed 2.4 GHz Wi-Fi and BLE connectivity.
It includes a 0.66″ SPI OLED display for real-time data visualization, a WS2812Caddressable RGB LED for system-status indication, a built-in buzzer for audible alerts, and front-panel buttons (SYS_SW) with a reset switch for local interaction. Astandard Grove I²C interface allows seamless integration with M5Stack hosts and various Grove sensors. The onboard USB Type-C port supports ESP32- C6 firmware programming, serial debugging, and 5 V power input, while automatic power switching and multi-channel ESD/surge protection ensure stable operation. Unit C6L excels at real-time data acquisition, edge-intelligence processing, and remote control, making it ideal for IoT applications such as smart agriculture, environmental monitoring, industrial IoT, smart buildings, asset tracking, and urban infrastructure sensing.\

1.1. Unit C6L

  1. Keupayaan Komunikasi
    Integrated LoRa (Semtech SX1262), supporting LoRaWAN Class A/B/Candpointto-point modes 2.4 GHz Wi-Fi and BLE via ESP32-C6-MINI-1U
  2. Pemproses & Prestasi
    Main Controller: Espressif ESP32-C6 (single-core RISC-V, up to 40 MHz) On-chip Memory: 512 KB SRAM with integrated ROM
  3. Pengurusan Kuasa & Tenaga
    Power Input: USB Type-C (5 V input) and Grove 5 V input
  4. Paparan & Penunjuk
    0.66″ SPI OLED display for real-time data visualization and status monitoringWS2812C addressable RGB LED for system-status indication Built-in buzzer for audible alerts
  5. Interfaces & Controls
    Grove I²C interface (with 5 V power) for seamless connection to M5Stack hostsandGrove sensors USB Type-C port for firmware programming, serial debugging, and power input Front-panel buttons (SYS_SW) and reset switch (MCU_RST) for local control
  6. Expansion & Debug Pads
    Bootloader pad: predefined jumper pad for entering bootloader mode Test points (TP1–TP8) for signal probing and in-circuit debug

2. SPESIFIKASI

Parameter Spesifikasi
MCU Espressif ESP32-C6(teras tunggal RISC-V, sehingga 40 MHz)
Komunikasi LoRaWAN; 2.4 GHz Wi-Fi BLE
Input Kuasa USB Jenis-C(5V) dan Grove 5V
Bekalan Voltage 3.3 V (LDO on-board)
Storan Denyar Denyar SPI 16 MB(128 Mbit)
Paparan 0.66”SPI OLED(128×64)
Penunjuk                                  LED RGB boleh alamat WS2812C
Buzzer Buzzer atas kapal
Butang System button (SYS_SW)and reset button(MCU_RST)
Antara muka Grove I²C; USB Type-C; pad pemuat but; pad nyahpepijat TP1-TP8
Antena 2×SSMB-JEF clamp penyambung;2×IPEX-4 penyambung antena
Suhu Operasi Suhu Operasi
Ciri-ciri Tambahan Multi-channel ESD/surge protection
Pengeluar M5Stack Technology Co., Ltd Block A10, Expo Bay South Coast, Fuhai Street, Bao’an District, Shenzhen, China
Frequency Range for CE 2.4G Wi-Fi: 2412-2472MHz BLE: 2402-2480MHz Lora: 868-868.6MHz
EIRP maksimum untuk CE BLE: 5.03dBm 2.4G Wi-Fi: 16.96dBm Lora: 9.45dBm
Kategori penerima The equipment provider declared that the receiver category for the EUTis2.
2.1 Saiz Modul
Saiz Modul

3. Amaran FCC

Awas FCC:
Sebarang Perubahan atau pengubahsuaian yang tidak diluluskan secara nyata oleh pihak yang bertanggungjawab untuk pematuhan boleh membatalkan kuasa pengguna untuk mengendalikan peralatan. Peranti ini mematuhi bahagian 15 Peraturan FCC. Pengendalian tertakluk kepada dua syarat berikut: (1) Peranti ini mungkin tidak menyebabkan gangguan berbahaya, dan (2) peranti ini mesti menerima sebarang gangguan yang diterima, termasuk gangguan yang boleh menyebabkan operasi yang tidak diingini.
NOTA PENTING:
Nota: This equipment has been tested and found to comply with the limits for a ClassBdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
betulkan gangguan dengan satu atau lebih langkah berikut:

  • Arahkan semula atau letakkan semula antena penerima.
  • Increase the separation betweentheequipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.
Pasang Arduino

I. Installing Arduino IDE(https://www.arduino.cc/en/Main/Software)
Klik untuk melawat rasmi Arduino webtapak , dan pilih pakej pemasangan untuk anda
operating system to download. Ⅱ. Installing Arduino Board Management
1. Pengurus Lembaga URL is used to index the development board information for specific platform. In the Arduino IDE menu, select File -> Keutamaan
Pasang Arduino

2.Salin pengurusan papan ESP URL di bawah ke dalam Pengurus Lembaga Tambahan
URLs: field, and save.
https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
Pasang Arduino
Pasang Arduino

3. Dalam bar sisi, pilih Pengurus Lembaga, cari ESP, dan klik Pasang.
Pasang Arduino

4. Dalam bar sisi, pilih Pengurus Lembaga, cari M5Stack, dan klik Pasang.
Depending on the product used, select the corresponding development board under
Tools -> Board -> M5Stack -> {ESP32C6 DEV Module board}.
Pasang Arduino

5. Sambungkan peranti ke komputer anda dengan kabel data untuk memuat naik program

M5STACK Logo

Dokumen / Sumber

Unit M5STACK Unit Pengkomputeran Tepi Pintar C6L [pdf] Manual Pemilik
M5UNITC6L, 2AN3WM5UNITC6L, Unit C6L Unit Pengkomputeran Tepi Pintar, Unit C6L, Unit Pengkomputeran Tepi Pintar, Unit Pengkomputeran Tepi, Unit Pengkomputeran, Unit

Rujukan

Tinggalkan komen

Alamat e-mel anda tidak akan diterbitkan. Medan yang diperlukan ditanda *