Panduan Operasi M5StickC Plus2
Firmware Kilang
Apabila peranti menghadapi masalah operasi, anda boleh cuba menghidupkan semula perisian tegar kilang untuk memeriksa sama ada terdapat sebarang kerosakan perkakasan. Rujuk tutorial berikut. Gunakan alat berkelip perisian tegar M5Burner untuk memancarkan perisian tegar kilang pada peranti.
Soalan Lazim
S1: Mengapa skrin M5StickC Plus2 saya hitam/tidak boleh but?
Penyelesaian: M5Burner Burn official Factory Firmware“M5StickCPlus2 User Demo”
S2: Mengapa masa bekerja hanya 3 jam? Mengapa ia dicas 100% dalam 1 minit, tanggalkan kabel pengecasan yang akan dimatikan?
Solutions: “Bruce for Stack plus2”This is an unofficial firmware. Flashing unofficial firmware can void your warranty, cause instability, and expose your device to security risks. Proceed with caution.
Sila bakar semula perisian tegar rasmi.
Persediaan
- Rujuk kepada tutorial M5Burner untuk melengkapkan muat turun alat berkelip perisian tegar, dan kemudian rujuk imej di bawah untuk memuat turun perisian tegar yang sepadan.
pautan muat turun: https://docs.m5stack.com/en/uiflow/m5burner/intro
Pemasangan Pemacu USB
Petua Pemasangan Pemandu
Klik pautan di bawah untuk memuat turun pemacu yang sepadan dengan sistem pengendalian anda. Pakej pemacu untuk CP34X (untuk versi CH9102) boleh dimuat turun dan dipasang dengan memilih pakej pemasangan yang sepadan dengan sistem pengendalian anda. Jika anda menghadapi masalah dengan muat turun program (seperti tamat masa atau ralat "Gagal menulis untuk menyasarkan RAM"), cuba pasang semula pemacu peranti.
CH9102_VCP_SER_Windows
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe
CH9102_VCP_SER_MacOS v1.7
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip
Pemilihan Port pada MacOS
Pada MacOS, mungkin terdapat dua port yang tersedia. Apabila menggunakannya, sila pilih port bernama wchmodem.
Pemilihan Pelabuhan
Sambungkan peranti ke komputer melalui kabel USB. Selepas pemasangan pemacu selesai, anda boleh memilih port peranti yang sepadan dalam M5Burner.
Terbakar
Klik "Bakar" untuk memulakan proses berkelip.
StickC-Plus2
SKU:K016-P2
Penerangan
StickC-Plus2 is the iterative version of Stick C-Plus. It is powered by the ESP32-PICO-V3-02 chip, providing Wi-Fi connectivity. Within its compact body, it integrates a rich variety of hardware resources, including IR emitter, RTC, microphone, LED, IMU, buttons, buzzer, and more. It features a 1.14-inch TFT display driven by the ST7789V2 with a resolution of 135 x 240.
The battery capacity has been increased to 200 mAh, and the interface is compatible with both HAT and Unit series modules.
This sleek and compact development tool can ignite unlimited creativity. StickC-Plus2 helps you quickly build IoT product prototypes and greatly simplifies the entire development process. Even beginners who are new to programming can create interesting applications and apply them in real life.
Tutorial
UIFlow
Tutorial ini akan memperkenalkan cara mengawal peranti StickC-Plus2 melalui platform pengaturcaraan grafik UIFlow.
UiFlow2
Tutorial ini akan memperkenalkan cara mengawal peranti StickC-Plus2 melalui platform pengaturcaraan grafik UiFlow2.
Arduino IDE
Tutorial ini akan memperkenalkan cara memprogram dan mengawal peranti StickC-Plus2 menggunakan IDE Arduino.
Nota
Port Not Recognized
When using a C-to-C cable, if the port cannot be recognized, please perform the following power-on procedure:
disconnect StickC-Plus2, power it off (long-press the power button until the green LED lights up), then reconnect the USB cable to power on.
Ciri-ciri
- Based on ESP32-PICO-V3-02 with Wi-Fi support
- Built-in 3-axis accelerometer and 3-axis gyroscope
- Integrated IR emitter
- Built-in RTC
- Mikrofon bersepadu
- User buttons, 1.14-inch LCD, power/reset button
- Bateri Li-ion 200 mAh
- Penyambung pengembangan
- Integrated passive buzzer
- Wearable & mountable
- Platform Pembangunan
- UiFlow1
- UiFlow2
- Arduino IDE
- ESP-IDF
- PlatformIO
Termasuk
- 1 x StickC-Plus2
Aplikasi
- Peranti boleh pakai
- IoT controller
- STEM education
- projek DIY
- Peranti rumah pintar
Spesifikasi
| Spesifikasi | Parameter |
| SoC | ESP32-PICO-V3-02 240 MHz dwi-teras, Wi-Fi, 2 MB PSRAM, 8 MB Denyar |
| Input Voltage | 5 V @ 500 mA |
| Antara muka | Jenis-C x 1, GROVE (I2C + I/O + UART) x 1 |
| Skrin LCD | 1.14 inci, LCD TFT 135 x 240 Warna, ST7789V2 |
| Mikrofon | SPM1423 |
| Butang | Butang pengguna x 3 |
| LED | Green LED x 1 (non-programmable, sleep indicator) Red LED x 1 (shares control pin G19 with IR emitter) |
| RTC | BM8563 |
| Buzzer | Buzzer pasif atas kapal |
| IMU | MPU6886 |
| Antena | 2.4 G antena 3D |
| Pin Luaran | G0, G25/G26, G36, G32, G33 |
| Bateri | 200 mAh @ 3.7 V, dalam |
| Suhu Operasi | 0 ~ 40 °C |
| Kepungan | Plastik (PC) |
| Saiz Produk | 48.0 x 24.0 x 13.5mm |
| Berat Produk | 16.7 g |
| Saiz Pakej | 104.4 x 65.0 x 18.0mm |
| Berat Kasar | 26.3 g |
Arahan Operasi
Hidupkan/Mati Kuasa
Power-on: Press the “BUTTON C” for more than 2 seconds, or wake up via the RTC IRQ signal. After the wake-up signal is triggered, the program must set the HOLD pin (G4) to high (1) to keep the power on, otherwise the device will shut down again.
Power-off: Without external USB power, press “BUTTON C” for more than 6 seconds, or set HOLD (GPIO4)=0 in the program to power off. While USB is connected, pressing “BUTTON C” for more than 6 seconds will turn off the screen and enter sleep mode (not a full power-off).
Skematik
Peta Pin
LED Merah & Pemancar IR | Butang A | Butang B | Buzzer
| ESP32-PICO-V3-02 | GPIO19 | GPIO37 | GPIO39 | GPIO35 | GPIO2 |
| IR Emitter & Red LED | IR emitter & Red LED pin | ||||
| Butang A | Butang A | ||||
| Butang B | Butang B | ||||
| Butang C | Butang C | ||||
| Buzzer Pasif | Buzzer |
Paparan TFT berwarna
Driver IC: ST7789V2
Peleraian: 135 x 240
| ESP32-PICO-V3-02 | G15 | G13 | G14 | G12 | G5 | G27 |
| Paparan TFT | TFT_MOSI | TFT_CLK | TFT_DC | TFT_RST | TFT_CS | TFT_BL |
Mikrofon MIC (SPM1423)
| ESP32-PICO-V3-02 | G0 | G34 |
| MIC SPM1423 | CLK | DATA |
6-Axis IMU (MPU6886) & RTC BM8563
| ESP32-PICO-V3-02 | G22 | G21 | G19 |
| IMU MPU6886 | SCL | SDA | |
| BM8563 | SCL | SDA | |
| Pemancar IR | TX | ||
| LED merah | TX |
HY2.0-4P
| HY2.0-4P | Hitam | merah | kuning | putih |
| PORT.CUSTOM | GND | 5V | G32 | G33 |
Saiz Model
Helaian data
ESP32-PICO-V3-02
ST7789V2
BM8563
MPU6886
SPM1423
Perisian
Arduino
StickC-Plus2 Arduino Quick Start
StickC-Plus2 Library
StickC-Plus2 Factory Test Firmware
UiFlow1
StickC-Plus2 UiFlow1 Mula Pantas
UiFlow2
StickC-Plus2 UiFlow2 Mula Pantas
PlatformIO
[env:m5stack-stickc-plus2]
platform = espressif32@6.7.0
board = m5stick-c
rangka kerja = arduino
upload_speed = 1500000
monitor_speed = 115200
build_flags =
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-issue
-DCORE_DEBUG_LEVEL=5
lib_deps =
M5Unified=https://github.com/m5stack/M5Unified
Pemacu USB
Click the links below to download the driver that matches your operating system. The package contains CP34X drivers (for CH9102). After extracting the archive, run the installer that matches your OS bit-depth.
If you encounter issues such as timeout or “Failed to write to target RAM” during downloading, please try reinstalling the driver.
| Nama Pemandu | Supported Chip | Muat turun |
| CH9102_VCP_SER_Windows | CH9102 | Muat turun |
| CH9102_VCP_SER_MacOS v1.7 | CH9102 | Muat turun |
macOS Port Selection
Two serial ports may appear on macOS. Please select the port named wchmodem.
Easy loader
Easy Loader is a lightweight program flasher that comes with a demonstration firmware. By following a few simple steps, you can flash it to the controller for quick functional verification.
| Easy loader | Muat turun | Nota |
| Factory Test for Windows | muat turun | / |
Lain-lain
Panduan Perisian Tegar Kilang Pemulihan StickC-Plus2
Video
StickC-Plus2 Feature Introduction
StackC Plus2 视频.mp4
Perubahan Versi
| Tarikh Tayangan | Tukar Penerangan | Nota |
| / | Keluaran pertama | / |
| 2021-12 | Added sleep and wake-up function, version updated to v1.1 | / |
| 2023-12 | Removed PMIC AXP192, MCU changed from ESP32-PICO-D4 to ESP32-PICO-V3-02, different power-on/off method, version v2 | / |
Perbandingan Produk
Perbezaan Perkakasan
| produk Nama |
SoC | Pengurusan Kuasa | Kapasiti Bateri | Ingatan | Cip USB-UART | warna |
| Stick C-Plus | ESP32-PICO-D4 | AXP192 | 120 mAh | 520 KB SRAM + 4 MB Denyar | CH522 | Red- orange |
| StickC-Plus2 | ESP32-PICO-V3-02 | / | 200 mAh | 2 MB PSRAM + 8 MB Flash | CH9102 | Jingga |
Perbezaan Pin
| Nama Produk | IR | LED | TFT | BUTANG A | BUTANG B | BUTANG C (BANGUN) |
TAHAN | Bateri Voltage Kesan |
| M5STICKC PLUS | G9 | G10 | MOSI (G15) CLK (G13) DC (G23) RST (G18) CS (G5) |
G37 | G39 | Biasa butang |
/ | Melalui AXP192 |
| M5STICKC PLUS2 | G19 | G19 | MOSI (G15) CLK (G13) DC (G14) RST (G12) CS (G5) |
G37 | G39 | G35 | G4 | G38 |
Perbezaan Hidupkan/Mati Kuasa
| produk Nama | Hidupkan kuasa | Matikan Kuasa |
| Stick C- Plus2 | Press “BUTTON C” for more than 2 s, or wake via RTC IRQ. After wake-up, set HOLD (G4)=1 in the program to keep power on, otherwise the device will shut down again. |
Without USB power, press “BUTTON C” for more than 6 s, or set HOLD (GPIO4)=0 in the program to power off. With USB connected, pressing “BUTTON C” for more than 6 s will turn off the screen and enter sleep, but not a full power- off. |
Oleh kerana StickC-Plus2 mengalih keluar PMIC AXP192, kaedah hidup/mati adalah berbeza daripada versi sebelumnya. Seperti yang dinyatakan pada permulaan dokumen ini, operasinya hampir sama, tetapi perpustakaan yang disokong akan berbeza. Kekuatan isyarat Wi-Fi dan IR kedua-duanya telah dipertingkatkan berbanding model sebelumnya.
Dokumen / Sumber
 |
M5STACK ESP32-PICO-V3-02 Modul Pembangunan IoT [pdf] Panduan Pengguna ESP32-PICO-V3-02 Modul Pembangunan IoT, ESP32-PICO-V3-02, Modul Pembangunan IoT, Modul Pembangunan, Modul |