Eccel C2R Pepper Module User Manual

Eccel C2R Pepper Module

Ciri-ciri

• Low cost RFID Reader with MIFARE® Classic® in 1K, 4K memory, ICODE, MIFARE Ultralight®, NTAG21x
• lifetime firmware updates
• Command interface via UART and USB
• Kadar baud UART sehingga 921600 bps
• High-speed USB-UART emulated interface
• USB HID keyboard emulation
• Penunjuk LED RGB boleh dikonfigurasikan untuk acara RFID
• 6 GPIO boleh dikonfigurasikan
• Mod bersendirian (undi)
• Kelajuan baca dan tulis transponder tinggi
• -25°C hingga 85°C julat operasi
• Rujukan dalaman berbilang voltages
• mematuhi RoHS
• CE (RED) and FCC compliant.
• ISED/PSE and other approvals were easily obtained

Aplikasi

• Kawalan capaian
• Memantau barangan
• Approval and monitoring of consumables
• Sistem pra-pembayaran
• Mengurus sumber
• Sistem storan data tanpa sentuh
• Penilaian dan pembangunan sistem RFID

Penerangan
The Pepper C2 Module RFID reader is the advanced successor to the Pepper C1 Module, maintaining full compatibility with most of the tag types and protocols supported by its predecessor. It offers lifetime firmware updates, ensuring continuous improvements and security. The device features a configurable USB interface capable of emulating either a UART interface or functioning as a HID profile, such as keyboard emulation. Additionally, the Pepper C2 Module is cost-optimized compared to previous C1 modules, providing enhanced functionality at a competitive price point.

Spesifikasi elektrik

Penilaian maksimum mutlak
Tekanan melebihi penilaian maksimum mutlak yang disenaraikan dalam jadual di bawah boleh menyebabkan kerosakan kekal pada peranti. Ini adalah penilaian tekanan sahaja, dan tidak merujuk kepada operasi berfungsi peranti yang harus mengikut keadaan pengendalian yang disyorkan.

Keadaan operasi

Current consumption (V_DD = 5V)

A metal environment near the antenna can increase the current consumption of the RFID Reader. Therefore, it is recommended to ensure a minimum 500mA of current from the power supply.

Bermula

IO dan persisian

Penerangan pinout

*All digital signals are at 3.3V level

Sambungan biasa

The Pepper C2R Module can be connected to a host (computer or another device) using USB or UART0. Both interfaces can be used for communication using the binary protocol described below.
The Module also has secondary UART (UART2) available. Using this connection, the user can view output logs which contain additional information about temporary executing commands. The default configuration is : baud: 115200, Data: 8 bit, Parity: none, Stop bits: 1 bit, Flow Control: none. Data lines can be configured to work using any free GPIO’s available on the module. Additionally, it can be used to operate the RS485 interface with hardware flow control using the DE and Re lines (pin no. 15 and 16).

The Pepper C2 device can be connected directly to a host computer using a standard USB interface. In the same way it can be powered to operate as a standalone device by using power sources such as a USB charger or power bank.
The computer operating system should recognize this device as a virtual com port or USB serial device and it should appear in Windows device manager as a COM port.

Figure 3-1. Typical connection
Hint – If you don’t have a USB-UART converter to see the logs on the UART2, you can temporarily change the default log interface from UART2 to UART0 in the Cx-client UART configuration button. Then, the logs should be available on the USB port

HID keyboard emulation
The RFID reader can be configured to enable USB port emulation of the HID Keyboard profile. With this functionality, UID numbers of tags read during polling are transmitted as a keyboard input stream to any host device that accepts USB keyboards. To activate this profile, the Cx-client application should be used to select the HID Keyboard profile for the USB port within the USB/UART configuration menu.
Once the device is configured via the USB/UART0 interface in HID Keyboard mode, further connection to this port using the Cx-client application becomes unavailable. In order to temporarily restore the binary protocol, the BUTTON pin should be held at the LOW state for 3 seconds. During this process, the device’s RGB LED blinks once every second and flashes red when the default UART emulation profile has been temporarily restored. Additionally, configuration options allow enabling automatic transmission of the ENTER key after each UID is sent.

Tetapan semula kilang
To restore the device to its factory default settings, the button pin must be held at LOW state for 10 seconds. The device will indicate the completion of the factory reset process by flashing the RGB LED in white.

Dimensi mekanikal

Pepper C2R Module
Semua dimensi adalah dalam mm.

Konfigurasi dan penerangan berfungsi

• Here is the document describing configuration, communication protocol, commands, and all functions of the Pepper C2 reader: https://eccel.co.uk/wp-content/downloads/Pepper_C2/C2-software-manual.pdf
• Eccel menyediakan pelbagai alatan & perpustakaan percuma sedia untuk dimuat turun dari pautan ini: https://eccel.co.uk/support-free-libraries/

Nota: Should you experience any difficulties integrating our readers into your device, please contact us at technical@eccel.co.uk. Our team can provide integration support and, where required, adapt the software and/or hardware to meet specific customer requirements. We specialize in developing custom solutions. Further information is available at: https://eccel.co.uk/custom-design/ 

Pelepasan RF dan Kelulusan Kerentanan
Eccel have tested and declared that this product meets all the requirements of the relevant RF directives (RED) to be declared CE (European Union) and UKCA (United Kingdom) compliant. Please see our declaration of conformity for this on the downloads tab of the product webpage. This product is designed to be incorporated into products easily and quickly, such that those products can pass any national or regional statutory RF requirements and certifications such as FCC (USA), ISED (Canada) and PSE (Japan) for example. This product is designed to meet all statutory RF requirements applicable worldwide using the most cost-effective but robust design methodology.
Eccel is pleased to offer customers very cost-effective certification for their end equipment that incorporates this product. Prices start from £3K per approval/ certification. Please contact us for more details at sales@eccel.co.uk.

PENYATA FCC

Amaran FCC
Peralatan ini telah diuji dan didapati mematuhi had untuk peranti digital Kelas B, menurut bahagian 15 Peraturan FCC. Had ini direka bentuk untuk memberikan perlindungan yang munasabah terhadap gangguan berbahaya dalam pemasangan kediaman. Peralatan ini menjana, menggunakan, dan boleh memancarkan tenaga frekuensi radio dan, jika tidak dipasang dan digunakan mengikut arahan, boleh menyebabkan gangguan berbahaya kepada komunikasi radio. Walau bagaimanapun, tiada jaminan bahawa gangguan tidak akan berlaku dalam pemasangan tertentu. Jika peralatan ini menyebabkan gangguan berbahaya kepada penerimaan radio atau televisyen, yang boleh ditentukan dengan mematikan dan menghidupkan peralatan, pengguna digalakkan untuk cuba membetulkan gangguan dengan satu atau lebih daripada langkah berikut:

• Arahkan semula atau letakkan semula antena penerima.
• Tingkatkan pemisahan antara peralatan dan penerima.
• Sambungkan peralatan ke dalam alur keluar pada litar yang berbeza daripada yang disambungkan kepada penerima.
• Rujuk pengedar atau juruteknik radio/TV yang berpengalaman untuk mendapatkan bantuan.

Awas: Sebarang perubahan atau pengubahsuaian pada peranti ini yang tidak diluluskan secara jelas oleh pengilang boleh membatalkan kuasa anda untuk mengendalikan peralatan ini.
Peranti ini mematuhi bahagian 15 Peraturan FCC. Operasi tertakluk kepada dua syarat berikut:
Peranti ini mungkin tidak menyebabkan gangguan berbahaya, dan (2) peranti ini mesti menerima sebarang gangguan yang diterima, termasuk gangguan yang boleh menyebabkan operasi yang tidak diingini.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/Canada. This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 5mm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna, As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Nota Penting: Sekiranya syarat ini tidak dapat dipenuhi (contohnyaample, certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2ALHY-C2RMODULE”

Arahan penyepaduan untuk pengeluar produk hos mengikut KDB 996369 D03 OEM Manual v01r01

Senarai peraturan FCC yang berkenaan
CFR 47 FCC Part 15 Subpart C has been investigated. It is applicable to the modular transmitter.

Syarat Penggunaan Operasi Khusus – Peletakan Antena Dalam Platform Hos
Modul ini adalah modular yang berdiri sendiri. Jika produk akhir akan melibatkan keadaan penghantaran Pelbagai serentak atau keadaan operasi yang berbeza untuk pemancar modular yang berdiri sendiri dalam hos, pengeluar hos perlu berunding dengan pengeluar modul untuk kaedah pemasangan dalam sistem akhir.

Prosedur Modul Terhad
Tidak berkenaan

Jejak Reka Bentuk Antena
Tidak berkenaan

Pertimbangan Pendedahan RF
Peranti telah dinilai untuk memenuhi keperluan pendedahan RF am. Peranti boleh digunakan dalam keadaan pendedahan mudah alih tanpa sekatan.

Jenis Antena dan Keuntungan
This radio transmitter FCC ID: 2ALHY-C2RMODULE has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Maklumat Pematuhan Pelabelan Produk Akhir
When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text: “Contains FCC ID: 2ALHY-C2RMODULE”. The FCC ID can be used only when all FCC compliance requirements are met.

Maklumat tentang Mod Ujian dan Keperluan Ujian Tambahan
This transmitter is tested in a standalone portable RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or for mobile products class II permissive change re-evaluation or new FCC authorization. Host manufacturer installed this module with single modular approval. The test of radiated emission and spurious emission according to FCC part 15C, 15.209, 15.207 requirement, only if the test result comply with FCC part 15C, 15.209, 15.207 requirement, then the host can be sold legally.

Ujian tambahan, Bahagian 15 Subbahagian B Penafian
Pemancar modular kami diuji sebagai subsistem dan pensijilannya tidak meliputi keperluan peraturan FCC Bahagian 15 Subbahagian B yang terpakai kepada hos terakhir. Hos terakhir masih perlu dinilai semula untuk pematuhan bahagian keperluan peraturan ini jika berkenaan. Selagi semua syarat di atas dipenuhi, ujian pemancar selanjutnya tidak diperlukan. Walau bagaimanapun, penyepadu OEM masih bertanggungjawab untuk menguji produk akhir mereka untuk sebarang keperluan pematuhan tambahan yang diperlukan dengan pemasangan modular ini.

Nota Pertimbangan EMI
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product that integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369. OEM/Host Manufacturer Responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules.

Cara Membuat Perubahan – Nota Penting
Sekiranya syarat ini tidak dapat dipenuhi (contohnyaampkonfigurasi komputer riba tertentu atau lokasi bersama dengan pemancar lain), maka kebenaran FCC tidak lagi dianggap sah dan ID FCC tidak boleh digunakan pada produk akhir. Dalam keadaan ini, penyepadu OEM akan bertanggungjawab untuk menilai semula produk akhir (termasuk pemancar) dan mendapatkan kebenaran FCC yang berasingan.

Sejarah semakan

MAKLUMAT LANJUT

• MIFARE, MIFARE Ultralight, MIFARE Plus, MIFARE Classic dan MIFARE DESFire ialah tanda dagangan NXP BV
• No responsibility is taken for the method of integration or final use of the Pepper C2 readers.
• More information about the Pepper C2 reader and other products can be found on the webtapak: http://www.eccel.co.uk  or alternatively contact Eccel Technology via e-mail at: sales@eccel.co.uk