CyberPower Personal Linux Software User Guide

CyberPower Personal Linux Software

Bermula

Nama
pwrstat Alat perintah keadaan kuasa UPS.

Sinopsis

Penerangan
pwrstat is an interface in PowerPaneI for Linux which allows users to receive UPS status and configure UPS settings.

Type the following command to list the manual: man pwrstat

Pilihan
Parameter pwrstat, fungsinya dan examples diterangkan di bawah:

Nota 1
Hujah berikut harus mengikuti -pwrfail.

Nota 2
Argumen berikut harus mengikuti -lowbatt.

Nota 3
Argumen berikut harus mengikuti -cloud.

Nota 4

1. Parameter -pwrfail dan -lowbatt perlu ditetapkan secara berasingan.
2. Both the shell scripts pwrstatd-lowbatt.sh and pwrstatd-powerfail.sh will be copied to Jetc during the installation procedure.
3. The parameter —cmd can be any shell script in the system, and it should be run as root to modify the settings.
4. The default system settings for -pwrfail and -lowbatt

Examples untuk Mengkonfigurasi Pilihan pwrstat

• Example 1: Configure the setting when a power failure event occurs. pwrstat -pwrfail -delay 60 -active on -cmd/etc/pwrstatd-powerfail.sh -duration 60 -shutdown on In the setting above, it will take 60 seconds to run a shell script named pwrstatd-powerfail.sh in the directory /etc, and the system will be shut down after a power failure event occurs for 60 seconds.
• Example 2: Configure the setting when the low battery event occurs. pwrstat-lowbatt -runtime -runtime -capacity -capacity – active on -cmd /etc/pwrstatd-lowbatt.sh -duration 1 -shutdown on In the setting above, it will take 1 minute to run a shell script named pwrstatd-lowbatt.sh in the directory /etc, and the system will be shut down when either the remaining runtime is less than 300 seconds, or the battery capacity is lower than 35%.
• Example 3a: Konfigurasikan sambungan ke PowerPanel Cloud.
  pwrstat -cloud -aktif pada -akaun example@cyberpower.com -laluan kata laluan123
  Assuming PowerPanel Cloud account/password: example@cyberpower.com / pass123. In the setting above, the connection to PowerPanel Cloud will be activated when users correctly enter their PowerPanel Cloud account and password.
• Example 3b: Sahkan sambungan ke PowerPanel Cloud.

pwrstat -sahkan

Untuk mengesahkan sama ada akaun dan kata laluan adalah betul, masukkan arahan di atas.

Terdapat tiga keputusan, diterangkan di bawah:

1. Apabila kedua-dua akaun dan kata laluan adalah betul, sistem akan menunjukkan Verify dengan jayanya.
2. Apabila sama ada akaun atau kata laluan salah, sistem akan menunjukkan Pengesahan gagal.
3. When a network issue exists, the system will show Connect failed

Halaman Daemon

Nama
pwrstatd Daemon keadaan kuasa UPS.

Penerangan
pwrstatd is the daemon of PowerPanel for Linux, which runs immediately when the system starts up and communicates with the UPS.

Type the following command to list the operations and the configuration files of the daemon: man pwrstatd

Operasi Daemon
Perintah untuk mengendalikan daemon pwrstatd dan fungsinya diterangkan di bawah:

Konfigurasi Files daripada Daemon
Konfigurasi files dan fungsinya diterangkan di bawah:

Nota 5
pwrstatd.conf boleh disunting dengan menggunakan mana-mana penyunting teks. Untuk mula mengedit konfigurasi file, type the following command as root:  vi/etc/pwrstatd.conf *

Take the text editor, vi, for example.
Perubahan yang diedit dalam editor teks akan berkuat kuasa selepas memulakan semula pwrstatd. Untuk memulakan semula daemon, taip arahan berikut: /etc/init.d/pwrstatd restart

Nota 6
To send the e-mail content in /etc/pwrstatd-email.sh, it is necessary to set ENABLE_EMAIL=yes and enter both the RECEIPT_ADDRESS and the SENDER_ADDRESS correctly in /etc/pwrstatd-lowbatt.sh or /etc/pwrstatd- powerfail.sh. For details about installing the e-mail package in Ubuntu, please refer to troubleshooting 6.

Log Peristiwa Daemon
The event logs of the pwrstatd daemon are located in the directory: /var/log. The file bernama pwrstatd.log merekodkan semua peristiwa kuasa.

Menyemak Tetapan Daemon

Type the following command to show the configuration of pwrstat:

Di bawah adalah bekasample for daemon configuration:

Tindakan untuk Kegagalan Kuasa:

Tindakan untuk Bateri Rendah:

Memantau Status UPS

Type the following command to show UPS properties and the current status:

pwrstat -status
Di bawah adalah bekasample untuk model UPS, CP585:

Nota 7
Beberapa item yang disenaraikan di atas hanya akan dipaparkan apabila model UPS menyokong fungsi yang berkaitan.

CYBERPOWER POWERPANEL
Sila layari https://www.cyberpower.com/content/software/eula/untuk melihat syarat EULA yang lengkap.