COMET TA0610 Web Manual Pengguna Sensor

PENERANGAN PRODUK

• Web Sensors TAx6x0 with an Ethernet connection are compact devices featuring internal sensors for temperature, relative humidity, barometric pressure, and CO2 concentration measurement. The devices can be powered either by a power supply adapter or via Power over Ethernet (PoE).
• The kepekatan CO2 is measured by an NDIR sensor using LED technology, ensuring low energy consumption and long-term measurement stability.
• Sensors with relative humidity measurement can also calculate derived humidity quantities such as dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy, humidex, and heat index.
• Nilai yang diukur dan dikira are displayed on a two-line LCD or can be read and processed via the Ethernet connection. The values are available on the device’s web interface and can be sent to the COMET Cloud online portal or the local COMET Database storage. The sensors also support integration with third-party data collection systems via Modbus TCP, HTTP GET (JSON and XML), HTTP POST (JSON), and SNMP protocols. An important feature of the devices is the ability to check measured values and notify via warning messages or acoustic/optical signals. Notification methods include status indication on the device’s website, e-mail alerts, and the Syslog protocol. The device can be configured through its web interface or via COMET Vision software, which is available free of charge from the manufacturer’s webtapak (www.cometsystem.com).

T…temperature, RH…relative humidity, CO2…concentration of CO2 in air, P…barometric pressure, CV…computed values

PEMASANGAN DAN PENGENDALIAN

The devices should be mounted on a flat surface according to the procedure detailed below. Careful attention should be paid to the installation of the devices and probes. Incorrect positioning or placement can adversely affect the accuracy and long-term stability of the measured values. Devices with a measuring stem must always be installed with the sensor cover facing downwards.

The devices do not require any special operation or maintenance. Periodic calibration is recommended to ensure measurement accuracy.

PENYEDIAAN PERANTI

To install the device and connect it to the network, you must have a free IP address. This address can be either static or obtained automatically from a DHCP server. Contact your network administrator and request permission before connecting the device. The device supports both IPv4 and IPv6 protocols. The device is configured to use DHCP by default. The IPv6 protocol is enabled in automatic mode (DHCPv6 or SLAAC) by default.

Connect the network cable and, if necessary, plug in the power adapter. Since the device is set to DHCP by default, you need to determine its IP address after connecting it. This can be done by searching for the device using the COMET Vision program, viewing the IP address in the gateway/DHCP server configuration, or displaying the IP address on the device’s display by pressing the button. Then enter the IP address into your web browser. From there, you can change the device settings. Configuration mode is activated by pressing the button on the home page. The changes are applied after saving the configuration.

PROTOKOL KOMUNIKASI DAN NEGERI RALAT

A detailed description of communication protocols and error states is available in the user manual on the manufacturer’s website. A brief overview of the communication protocols can also be viewed directly on the device’s web antara muka.

ARAHAN KESELAMATAN

• The device does not have enhanced protection against water or dust ingress. Never use it in environments with splashing or dripping water, condensation, aerosols, or excessive dust.
• The device must not be operated or stored without a sensor cover.
• The humidity sensors should not be exposed to water or other liquids.
• Use a power adapter approved according to the relevant standards. Use only IEEE 802.3af PoE.
• The device is not intended for use in critical applications where a communication failure could endanger health or cause material damage. Ensure proper cybersecurity measures when operating the device.
• Installation should only be performed by qualified personnel in accordance with applicable regulations and standards.
• The devices contain electronic components and must be disposed of in accordance with current regulations.
• Untuk maklumat tambahan, refer to the manuals and other documentation available in the “Download” section for each device at www.cometsystem.com

Spesifikasi teknikal

* valid for the TA7610 device only

** valid at a temperature of 15-35°C. In the measurement range of 5 000 to 10 000 ppm, the accuracy is ±10% of the measured value.

Button – functions

• Factory defaults procedure: turn off the device • press and hold the button • turn on the device • release the button
• Mute of active acoustic signaling: tekan butang sebentar
• Displaying device IP address (in case the acoustic signaling is not active): press the button briefly

Pemasangan peranti

1. Select holder mounting method: Select one of the device holder mounting methods and fasten the holder.
2. Slide device onto holder: Slide the device onto the holder.
3. Sambungkan kabel: Connect the Ethernet cable (if PoE power supply is not used, connect the adapter).