CISCO ESW6300 Mendayakan Port USB pada Titik Akses

Spesifikasi

• USB Port Power: Up to 2.5W (some models support up to 4.5W)
• Fungsi Port USB: Sumber kuasa untuk peranti USB

Arahan Penggunaan Produk

Mendayakan Port USB pada Titik Akses:
To enable the USB port on your Cisco Access Point for powering USB devices:

1. Check if your AP model supports a USB power source by referring to the datasheet.
2. Konfigurasikan AP Profile menggunakan CLI:
   • Masukkan mod konfigurasi global: configure terminal
   • Buat AP profile: ap profile xyz-ap-profile
   • Dayakan USB untuk AP profile: usb-enable
   • Keluar dari mod konfigurasi: end
3. Konfigurasikan tetapan USB untuk Titik Akses menggunakan CLI:
   • Masukkan mod EXEC istimewa: enable
   • Enable the USB port on the AP: ap name AP44d3.xy45.69a1 usb-module override

Port USB sebagai Sumber Kuasa untuk Titik Akses
Some Cisco APs have a USB port that can act as a source of power for some USB devices. The power can be up to 2.5W; if a USB device draws more than 2.5W of power, the USB port shuts down automatically. The port is enabled when the power draw is 2.5W or lower. Refer to the datasheet of your AP to check if the AP has a USB port that can act as a source of power.

Nota 
Both IW6300 and ESW6300 APs have a USB port that can act as a source of power up to 4.5W for some USB devices.

Nota
The controller records the last five power-overdrawn incidents in its logs.

Berhati-hati

When an unsupported USB device is connected to the Cisco AP, the following message is displayed:
The inserted USB module is not a supported device. The behaviour of this USB device and its impact on the Access Point are not guaranteed. If Cisco determines that a fault or defect can be isolated due to the use of third-party USB modules installed by a customer or reseller, Cisco may withhold support under warranty or the support program under contract. In the course of providing support for Cisco networking products, the end user may be required to install Cisco-supported USB modules in the event Cisco determines that removing third-party parts will assist Cisco in diagnosing the root cause for troubleshooting purposes. Cisco also reserves the right to charge the customer per the then-current time and material rates for services provided to the customer when Cisco determines, after having provided such services, that an unsupported device caused the root cause of the defective product.

Mengkonfigurasi AP Profile (CLI)

Prosedur

	Perintah atau Tindakan	Tujuan
Langkah 1	konfigurasi terminal Example: terminal konfigurasi # peranti	Memasuki mod konfigurasi global.
Langkah 2	ap profileAP-profilee Example: Peranti(konfigurasi)# ap profile xyz-ap-profile	Mengkonfigurasi AP profile and enters the AP profile mod konfigurasi. Nota When you delete a named profile, the APs associated with that profile will not revert to the default profile.
Langkah 3	usb-enable Example: Peranti(config-ap-profile)# usb-enable	Mendayakan USB untuk setiap AP profile. Nota By default, the USB port on the AP is disabled.   Gunakan no USB-Enable command to disable USB for each AP profile.
Langkah 4	tamat Example: Peranti(config-ap-profile)# tamat	Kembali ke mod EXEC istimewa. Sebagai alternatif, anda juga boleh menekan Ctrl-Z untuk keluar dari mod konfigurasi global.

Mengkonfigurasi Tetapan USB untuk Titik Akses (CLI)

Prosedur

	Perintah atau Tindakan	Tujuan
Langkah 1	membolehkan Example: Peranti# membolehkan	Memasuki mod EXEC istimewa.
Langkah 2	nama ap nama-ap usb-module Example: Peranti# ap name AP44d3.xy45.69a1 usb-module	Enables the USB port on the AP. Gunakan nama ap nama-ap no usb-module Command to disable the USB port on the AP. Nota If you are using a Cisco Catalyst 9105AXW AP and you enable the USB port (3at PoE-in), it is not possible to enable the USB PoE-out at the same time.
Langkah 3	nama ap nama-ap usb-module override Example: Peranti# ap name AP44d3.xy45.69a1 usb-module override	Overrides the USB status of the AP profile and considers the local AP configuration. Gunakan nama ap nama-ap no usb-module override command to override the USB status of the AP and consider the AP profile konfigurasi. Nota You can configure the USB status for an AP only if you enable USB override for it.

Mengkonfigurasi Tetapan USB untuk Titik Akses (GUI)

Prosedur

• Step 1: Choose Configuration >Wireless > Access Points.
• Step 2: In the Access Points window, click the name of the AP.
• Step :3 In the Edit AP window, click the Interfaces tab.
• Step: 4 In the USB Settings section, configure the USB Module State as either of the following:
  • ENABLED: Enables the USB port on the AP
  • DISABLED: Disables the USB port on the AP
• Nota
  If you are using Cisco Catalyst 9105AXW AP and if you enable the USB por3at3at PoE-in, it is not possible to enable the USB PoE-out at the same time.
• Step 5: Configure USB Override as either of the following:
  • ENABLED: Overrides USB status of the AP profile and considers the local AP configuration
  • DISABLED: Overrides USB status of the AP and considers the AP profile konfigurasi
  • Nota
    You can configure the USB status for an AP only if you enable USB override for it.
• Step 6: Click Apply & Update to Device.

Memantau Konfigurasi USB untuk Titik Akses (CLI)

• Kepada view the inventory details of APs, use the following command: show ap name ap-name inventory
• Berikut adalah sebagaiampkeluaran:
  • Device# show ap name AP500F.8059.1620 inventory
  • Device# show ap name AP500F.8059.1620 inventory
• Berikut adalah sebagaiampkeluaran:
  • NAME: AP280  DESCR: Cisco Aironet 2800 Series (IEEE 802.11ac) Access Point
  • PID: AIR-AP2802I-D-K9 , VID: 01, SN: XXX1111Y2ZZZZ2800
  • NAME: SanDisk, DESCR: Cruzer Blade
  • PID: SanDisk , SN: XXXX1110010, MaxPower: 224
• Kepada view the summary of an AP module, use the following command: show ap module summary
• Berikut adalah sebagaiampkeluaran:
  • Peranti# tunjukkan ringkasan modul ap
• AP Name External Module External Module PID External Module

Penerangan
AP500F.1111.2222 Enable SanDisk Cruzer Blade

• Kepada view the USB configuration details for each AP, use the following command: show ap name ap-name config general
• Berikut adalah sebagaiampkeluaran:
  • Peranti# tunjukkan nama ap AP500F.111.2222 umum konfigurasi
  • USB Module Type……………………………. USB Module
  • USB Module Status………………………….. Disabled
  • USB Module Operational State………………… Enabled
  • USB Override …………………………….. Enabled
• Kepada view sthe status of the USB module, use the following command: show ap profile nama xyz terperinci
• Berikut adalah sebagaiampkeluaran:
  • Peranti# tunjukkan ap profile nama xyz terperinci
  • USB Module: ENABLED

Soalan Lazim

Q: How can I tell if my AP supports a USB power source?

A: You can refer to the datasheet of your AP to check if it has a USB port that can act as a power source for USB devices.

S: Apakah yang berlaku jika peranti USB yang disambungkan menarik lebih daripada 2.5W kuasa?

A: If a USB device draws more than 2.5W of power, the USB port shuts down automatically to prevent damage.

Dokumen / Sumber

CISCO ESW6300 Mendayakan Port USB pada Titik Akses [pdf] Manual Arahan IW6300, ESW6300, ESW6300 Mendayakan Port USB pada Pusat Akses, Mendayakan Port USB pada Pusat Akses, Port USB pada Pusat Akses, Pusat Akses

Rujukan

• Manual Pengguna