Cdtech TP300 Bluetooth Module Owner’s Manual

Cdtech TP300 Bluetooth Module

Berakhirview
CDI-WC46600A-01 is a Wi-Fi + BLE module independently developed by Cdtech based on the ECR6600-ATS2L chip. ECR6600-ATS2L is a SoC chip designed for smart home IoT terminal devices, supporting Wi-Fi 802.11b/g/n/ax and BLE 5.1 protocols. It includes a power management module, power amppenguat, bunyi rendah amplifier, and transceiver switch. ECR6600-ATS2L adopts a RISC processor architecture, has ample storage space, rich peripheral interfaces, a more secure encryption mechanism, an on-chip FullMAC architecture, and a wider operating temperature range.

Ciri-ciri

Ciri Wi-Fi

• Supports IEEE 802.11 b/g/n/ax
• Supports Full MAC, including LMAC and UMAC
• Supports SoftAP, STA, and Wi-Fi direct connection mode
• Supports WMM QoS
• Supports 0.8/1.6/3.2 US security protection intervals
• Supports 802.11 ax MCS0 – MCS7
• The maximum bit rate reaches 150 Mbps
• Both uplink and downlink support MU-OFDMA (STA is supported)
• STA supports beamforming (STA acts as the Beamformer)
• Supports Mid-amble
• Supports 20 M and 40 M bandwidth. 802.11ax only supports 20 M bandwidth.
• Supports dual carrier modulation (Dual Carrier Modulation, DCM)

Ciri BLE

• Supports BLE 5.1 protocol (does not support AOA/AOD)
• Supports single-device BLE connection
• Supports synchronous broadcasting and scanning
• Supports enhanced power control
• Output power up to +8 dBm
• Supports adaptive frequency hopping (AFH)
• Menyokong penghantaran dan penerimaan data tak segerak
• Supports connection parameter update
• Supports extensible data packet length
• Menyokong penyulitan lapisan pautan
• Menyokong ping LE

The Wi-Fi subsystem and BLE subsystem share the radio part, including ADC/DAC/PLL. Wi-Fi and BLE can only have one working at a time.

Spesifikasi Umum

Pin description and PCBA size

Note: Method for downloading the module: VCC, GND, EN (pull-up), UART0_TX, UART0_RX, RESET_B (connected to the RTS of the serial port)

Module physical picture

Bil bahan

Ciri-ciri elektrik

Direct-current characteristic

Suggested working conditions

Reflow soldering curve graph

Dirujuk kepada piawaian IPC/JEDEC.

• Suhu Puncak : <250°C
• Bilangan Kali: ≤2 kali

package figure

Arahan Pembungkusan

1. 700pcs

   • Each reel is loaded with 700 pcs (leave 20 empty pockets at both the front and back without components).

2. Perform vacuum packaging once the taping process is complete.

3. After vacuum packaging, place the taped reel into the inner box (700 pcs total per box).

4. 700pcs × 5 = 3500pcs

   • Each outer carton holds 5 inner boxes, for a total capacity of: $700\text{ pcs} \times 5 = 3500\text{ pcs}$.

WC46600A-01 is an ESD (Electrostatic Discharge) sensitive component. ESD or peak voltage may cause damage to the device. Although the WC46600A-01 has an internal ESD protection circuit, please handle it with care to avoid causing permanent damage or performance degradation.

Pensijilan
Arahan penyepaduan untuk pengeluar produk hos mengikut KDB 996369 D03 OEM Manual v01r01

Senarai peraturan FCC yang berkenaan
CFR 47 FCC Part 15 Subpart C and Subpart C has been investigated. It is applicable to the modular transmitter.

Syarat Penggunaan Operasi Khusus
Antenna Placement Within the Host Platform The module is tested for mobile RF exposure use condition.. The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for exampkonfigurasi komputer riba tertentu atau lokasi bersama dengan pemancar lain), maka kebenaran FCC tidak lagi dianggap sah dan ID FCC tidak boleh digunakan pada produk akhir. Dalam keadaan ini, penyepadu OEM akan bertanggungjawab untuk menilai semula produk akhir (termasuk pemancar) dan mendapatkan kebenaran FCC yang berasingan.

Prosedur Modul Terhad
Tidak berkenaan

Jejak Reka Bentuk Antena
Tidak berkenaan

Pertimbangan Pendedahan RF
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be mobile RF exposure use condition.

Jenis Antena dan Keuntungan

• Antena berikut telah diperakui untuk digunakan dengan modul ini.
• Hanya antena dari jenis yang sama dengan keuntungan yang sama atau lebih rendah juga boleh digunakan dengan modul ini.
• Jenis antena lain dan/atau antena keuntungan lebih tinggi mungkin memerlukan kebenaran tambahan untuk operasi.

Maklumat Pematuhan Pelabelan Produk Akhir
When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text:“Contains FCC ID:2AATP-TP300”. The FCC ID can be used only when all FCC compliance requirements are met.

Maklumat tentang Mod Ujian dan Keperluan Ujian Tambahan
This transmitter is tested in mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) class II permissive change re-evaluation or new FCC authorization. Host manufacturer installed this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C, 15.209, 15.207 requirements, only if the test result comply with FCC part 15C, 15.209, 15.207 requirement, then the host can be sold legally.

Ujian tambahan, Bahagian 15 Subbahagian B Penafian
This transmitter modular us tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rules requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of the rules requirements if applicable. As long as all conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this modular installed.

Maklumat Manual kepada Pengguna Akhir
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation of the rules, including the transmitter operation, and should refer to guidance in KDB Publication 996369. OEM/Host Manufacturer Responsibilities: OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules

Cara Membuat Perubahan – Nota Penting
Jika syarat ini tidak dapat dipenuhi (contohnyaamptetapi, konfigurasi komputer riba tertentu atau lokasi bersama dengan pemancar lain), maka kebenaran FCC tidak lagi dianggap sah dan ID FCC tidak boleh digunakan pada produk akhir. Dalam keadaan ini, penyepadu OEM akan bertanggungjawab untuk menilai semula produk akhir (termasuk pemancar) dan mendapatkan kebenaran FCC yang berasingan.

Penyata FCC

Peranti ini hanya bertujuan untuk penyepadu OEM di bawah syarat berikut

1. The antenna must be installed such that 20 cm is maintained between the antenna and the user.
2. Modul pemancar mungkin tidak ditempatkan bersama dengan mana-mana pemancar atau antena lain.

• Module Antenna Type: 2.4GHz onboard FPC Antenna, 2.68 dBi peak gain.

Peranti ini mematuhi Bahagian 15 Peraturan FCC. Operasi tertakluk kepada dua syarat berikut:

1. Peranti ini mungkin tidak menyebabkan gangguan berbahaya.
2. Peranti ini mesti menerima sebarang gangguan yang diterima, termasuk gangguan yang boleh menyebabkan operasi yang tidak diingini.

Catatan: Penerima tidak bertanggungjawab atas sebarang perubahan atau pengubahsuaian yang tidak diluluskan secara tegas oleh pihak yang bertanggungjawab untuk pematuhan. Pengubahsuaian tersebut boleh membatalkan hak pengguna untuk mengendalikan peralatan tersebut.

NOTA: Peralatan ini telah diuji dan didapati mematuhi had untuk peranti digital Kelas B, menurut bahagian 15 Peraturan FCC. Had ini direka bentuk untuk memberikan perlindungan yang munasabah terhadap gangguan berbahaya dalam pemasangan kediaman. Peralatan ini menjana kegunaan dan boleh memancarkan tenaga frekuensi radio dan, jika tidak dipasang dan digunakan mengikut arahan, boleh menyebabkan gangguan berbahaya kepada komunikasi radio. Walau bagaimanapun, tiada jaminan bahawa gangguan tidak akan berlaku dalam pemasangan tertentu. Jika peralatan ini menyebabkan gangguan berbahaya kepada penerimaan radio atau televisyen, yang boleh ditentukan dengan mematikan dan menghidupkan peralatan, pengguna digalakkan untuk cuba membetulkan gangguan dengan satu atau lebih daripada langkah berikut:

• Arahkan semula atau letakkan semula antena penerima.
• Tingkatkan pemisahan antara peralatan dan penerima.
• Sambungkan peralatan ke dalam alur keluar pada litar yang berbeza daripada yang disambungkan kepada penerima.
• Rujuk pengedar atau juruteknik radio/TV yang berpengalaman untuk mendapatkan bantuan.

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369.OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule, such as FCC Part 15 Subpart B, before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules.

Kenyataan Pendedahan RF
Peralatan ini mematuhi had pendedahan sinaran FCC yang ditetapkan untuk persekitaran yang tidak terkawal. Peralatan ini hendaklah dipasang dan dikendalikan dengan jarak minimum 20 cm antara radiator dan badan anda