BlackSpider BSA15.4 15000W 4 Saluran AmpManual Pengguna yang lebih hidup

pengenalan

Thank you for choosing the BlackSpider BSA15.4 15000W 4 Channel Amppengikat. ini amplifier is designed to deliver high-efficiency power and precision audio performance for your car audio system. Please read this manual thoroughly before installation and operation to ensure proper use and to maximize the performance and longevity of your amplebih hidup.

Maklumat Keselamatan Penting

• Sentiasa putuskan sambungan terminal negatif bateri kenderaan sebelum memulakan sebarang pemasangan.
• Pastikan pembumian yang betul amppengalir ke casis kenderaan.
• Use appropriate gauge wiring for power, ground, and speaker connections to prevent overheating and damage.
• Pasangkan amplifier in a well-ventilated area to prevent overheating. Avoid mounting in enclosed spaces without airflow.
• Lindungi semua pendawaian daripada tepi tajam dan bahagian yang bergerak.
• Jangan kendalikan amplifier if it is damaged or malfunctioning. Refer to the troubleshooting section or contact support.
• Pemasangan profesional disyorkan untuk prestasi dan keselamatan yang optimum.

Kandungan Pakej

Sahkan bahawa semua item terdapat dalam pakej:

• BlackSpider BSA15.4 4 Channel Amplebih hidup
• Fuses (pre-installed or spare)
• Kurung Pemasangan
• Skru
• Manual Pengguna (dokumen ini)

Produk Selesaiview

The BlackSpider BSA15.4 is a 4-channel Class AB amplifier featuring a high-efficiency MOSFET power amplifier design. It is engineered for reliable high-power output and flexible system setups.

Ciri-ciri Utama:

• High Efficiency MOSFET Power Ampreka bentuk penguat
• 2Ω Stable Circuitry for reliable high-power output
• Bridgeable Channel Configuration for flexible system setups
• Variable High & Low Pass Crossover to fine-tune your audio
• Rear Channel Bass Boost for enhanced low-end response
• Integrated Cooling Fan for consistent thermal control
• Built-in Protection Circuitry against thermal overload, short circuits, and excessive current

Amplifier Layout:

Pemasangan dan Persediaan

Pemasangan yang betul adalah penting untuk prestasi dan keselamatan yang optimum. Jika anda tidak pasti tentang sebarang langkah, rujuk pemasang profesional.

1. Lokasi Pemasangan:

• Choose a location that is dry, well-ventilated, and protected from direct sunlight and excessive heat.
• Pastikan ruang yang mencukupi di sekeliling amplifier for airflow, especially around the cooling fan.
• Elakkan memasang amplifier where it could be exposed to moisture or excessive vibration.
• Pasang dengan selamat amplifier using the provided mounting brackets and screws to prevent movement.

2. Sambungan Pendawaian:

Sebelum membuat sebarang sambungan, cabut terminal negatif bateri kenderaan.

• Kuasa (+12V): Connect a heavy-gauge power cable directly from the positive terminal of the vehicle's battery to the +12V terminal on the amplifier. Install an in-line fuse holder (not supplied) within 18 inches (45 cm) of the battery.
• Tanah (GND): Connect a heavy-gauge ground cable from the GND terminal on the amplifier to a clean, unpainted metal surface of the vehicle's chassis. Ensure a solid, low-resistance connection.
• Alat Kawalan Jauh (REM): Sambungkan wayar hidup jauh dari output jauh unit kepala anda ke terminal REM pada amppengalir. Wayar ini memusingkan amphidupkan dan matikan lampu dengan unit kepala anda.
• Input RCA: Sambungkan kabel RCA daripada pra-unit kepala andaamp output kepada amplifier's RCA input jacks (Front L/R, Rear L/R).
• Output pembesar suara: Connect your speakers to the appropriate speaker output terminals. Observe correct polarity (+ to + and - to -).
• Mod Jambatan: For higher power output to a single speaker (e.g., a subwoofer), you can bridge two channels. Refer to the "Operating Instructions" section for details on bridging.

Caution: Ensure all connections are secure and properly insulated to prevent short circuits.

Arahan Operasi

1. Initial Power-Up and Basic Settings:

1. After all connections are made, reconnect the vehicle's negative battery terminal.
2. Hidupkan unit kepala anda. amplifier should power on (indicated by a power LED).
3. Start with all gain controls on the amplifier set to minimum.
4. Set your head unit's volume to about 75% of its maximum.
5. Slowly increase the gain controls on the amplifier until you hear distortion, then back off slightly. This sets the maximum clean output level.

2. Tetapan Crossover:

The BSA15.4 features variable high-pass (HPF) and low-pass (LPF) crossovers to optimize sound for different speakers.

• HPF (Penapis Lulus Tinggi): Allows frequencies di atas the set point to pass through. Use for full-range speakers or tweeters to protect them from low bass frequencies.
• LPF (Penapis Lulus Rendah): Allows frequencies di bawah the set point to pass through. Use for subwoofers to ensure they only reproduce bass.
• PENUH: Disables the crossover, allowing the full frequency range to pass.
• Adjust the HPF/LPF knobs according to your speaker types and desired sound. Typical settings:
  • Full-range speakers: HPF set between 80Hz - 120Hz.
  • Subwoofers (when bridged): LPF set between 80Hz - 120Hz.

3. Peningkatan Bass:

The rear channels feature a variable Bass Boost control to enhance low-end response.

• Adjust the Bass Boost knob to your preference. Use sparingly to avoid distortion and speaker damage.

4. Bridged Channel Configuration:

The BSA15.4 allows bridging of two channels to create a single, higher-power output for a subwoofer.

• To bridge channels, connect the positive (+) terminal of the subwoofer to the positive (+) terminal of one channel (e.g., R+ of Rear) and the negative (-) terminal of the subwoofer to the negative (-) terminal of the adjacent channel (e.g., L- of Rear). Refer to the amplifier's rear panel diagram for specific bridging connections.
• When bridging, ensure the subwoofer's impedance is within the amplifier's stable operating range (e.g., 4Ω bridged).
• Set the crossover for the bridged channels to LPF for subwoofer operation.

Penyelenggaraan

• Pembersihan: Lap secara berkala ampLap bahagian luar penapis dengan kain yang lembut dan kering. Jangan gunakan bahan kimia yang keras atau pembersih yang kasar.
• Pengudaraan: Ensure the cooling fan and heatsink fins remain free of dust and debris to maintain proper airflow and prevent overheating.
• Sambungan: Occasionally check all wiring connections for tightness and corrosion. Loose connections can cause performance issues or damage.
• Sekering: If a fuse blows, replace it only with a fuse of the same type and rating. Using an incorrect fuse can lead to damage or fire.

Menyelesaikan masalah

Spesifikasi

Waranti dan Sokongan

The BlackSpider BSA15.4 amplifier comes with a manufacturer's warranty of 1 Tahun dari tarikh pembelian. Waranti ini melindungi kecacatan pada bahan dan mutu kerja di bawah penggunaan biasa.

Waranti tidak melindungi kerosakan yang disebabkan oleh:

• Pemasangan atau pendawaian yang tidak betul.
• Kemalangan, penyalahgunaan atau penyalahgunaan.
• Exposure to moisture or extreme temperatures.
• Pembaikan atau pengubahsuaian tanpa kebenaran.

For warranty claims or technical support, please contact your authorized BlackSpider dealer or visit the official BlackSpider website for contact information. Please have your proof of purchase and product model number (BSA15.4) ready when contacting support.