ERKUL 5.2" Running Boards for Subaru Forester 2014-2018

1. Pengenalan

This manual provides comprehensive instructions for the installation, maintenance, and general use of your ERKUL 5.2" Running Boards. These running boards are designed to fit Subaru Forester models from 2014 to 2018, offering enhanced vehicle access and protection. Please read all instructions carefully before beginning installation.

Image 1: Erkul 5.2" Running Boards installed on a white Subaru Forester.

2. Maklumat Keselamatan

• Always wear appropriate personal protective equipment, such as safety glasses and gloves, during installation.
• Ensure the vehicle is securely supported on a level surface using jack stands or a car lift before working underneath.
• Do not overtighten bolts, as this may damage components. Refer to vehicle manufacturer specifications for torque values if available.
• Jauhkan kanak-kanak dan haiwan peliharaan dari kawasan kerja.
• If you are unsure about any step of the installation process, seek professional assistance.

3. Kandungan Pakej

Sahkan bahawa semua komponen yang disenaraikan di bawah ada dan tidak rosak sebelum memulakan pemasangan:

• Pair of Running Boards (Left and Right)
• Pair of Brackets (Vehicle-specific, typically Front and Rear for each side)
• All Necessary Mounting Hardware (Bolts, Washers, Nuts)

Image 2: Key features of the Erkul Running Boards.

4. Arahan Pemasangan

Nota: While these running boards are designed for no-drill installation, professional installation is recommended, especially if your vehicle is lower to the ground or if you are unfamiliar with vehicle modifications.

4.1. Alatan Diperlukan

• Set Kunci Soket
• Screwdriver (Flathead or Phillips, depending on vehicle trim clips)
• Pry Tool (Plastic, to avoid scratching)
• Measuring Tape (Optional, for alignment)

4.2. Panduan Pemasangan Langkah demi Langkah

The following video demonstrates a general installation process for ERKUL running boards. While the vehicle shown in the video is a Jeep Renegade, the fundamental steps for bracket attachment and running board mounting are similar for the Subaru Forester. Please refer to your specific vehicle's undercarriage for exact mounting points.

1. Penyediaan Kenderaan: Raise the vehicle using a car lift or secure jack stands to provide adequate working space underneath.
2. Cari Titik Pemasangan: Identify the factory mounting points on the vehicle's chassis. These are typically pre-drilled holes or existing bolts along the rocker panel. You may need to remove plastic covers or plugs to access these points.
3. Install Front Bracket: Secure the front bracket to the designated front mounting points on the vehicle's frame using the provided hardware. Hand-tighten bolts initially to allow for adjustment.
4. Install Rear Bracket: Secure the rear bracket to the designated rear mounting points. Again, hand-tighten bolts.
5. Prepare Running Board: Insert the T-bolts into the channels on the underside of the running board. Position them to align with the bracket mounting holes.
6. Mount Running Board: Carefully lift the running board and align the T-bolts with the holes on the installed brackets. Secure with washers and nuts, hand-tightening only.
7. Adjust and Final Tighten: Adjust the running board for proper alignment and desired position. Once satisfied, fully tighten all bolts on the brackets and the running board using a socket wrench. Ensure all connections are secure.
8. Ulangi untuk Bahagian Lain: Follow the same steps for installing the running board on the opposite side of the vehicle.

Imej 3: Sisi view of running boards installed on a vehicle.

5. Penyelenggaraan

• Pembersihan tetap: Clean the running boards regularly with mild soap and water to remove dirt, road grime, and salt. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
• Periksa Pengikat: Periodically check all mounting bolts and nuts to ensure they remain tight. Re-tighten if necessary to prevent loosening due to vehicle vibration.
• Semak Kerosakan: Inspect the running boards and brackets for any signs of damage, corrosion, or wear. Replace any damaged components immediately to maintain safety and structural integrity.

6. Penyelesaian masalah

• Loose Running Board: If the running board feels loose or wobbly, re-check all mounting bolts and nuts for proper tightness. Ensure brackets are correctly seated.
• Bunyi Luar Biasa: Squeaking or rattling sounds may indicate loose fasteners or improper installation. Inspect all contact points and tighten as needed.
• Kesukaran Menjajarkan: Ensure the correct brackets are used for the front and rear positions, and that the running board is oriented correctly. Slight adjustments may be needed before final tightening.

7. Spesifikasi

8. Waranti dan Sokongan

ERKUL products are manufactured with quality and durability in mind. For specific warranty details, please refer to the product packaging or contact ERKUL customer service directly. For any installation questions or support, ERKUL offers dedicated after-sales support.

Image 4: ERKUL After-Sales Support.