Irfora QDB-3A Ignition Coil Tester User Manual

1. Pengenalan

The Irfora QDB-3A Ignition Coil Tester is a versatile diagnostic instrument designed for automotive maintenance. It offers a range of functions to quickly identify component problems in various vehicle systems. This manual provides detailed instructions for the proper use and operation of the device.

Key functions include PWM drive output, stepper motor drive, PWM signal output, and voltage/resistance measurement.

2. Ciri-ciri Utama

• Versatile Testing Capabilities: Drives and tests ignition coils, fuel injectors, solenoid valves, fuel metering valves, idle stepping motors, instrument stepping motors, headlight follow-up steering stepping motors, and urea pump motors.
• High-Precision Simulation: Generates Hall signals with adjustable output frequency, amplitude, and duty ratio to simulate various duty cycle sensors (e.g., air conditioning pressure sensors, air flowmeters).
• Ciri Keselamatan yang Dipertingkatkan: Operates with a power supply voltage range of 12V to 24V, incorporating reverse connection and overcurrent protections for equipment safety.
• Wide Adjustment Ranges: Electromagnetic coil driving current from 0 to 3.5A, output frequency from 1Hz to 100KHz, duty cycle adjustment from 1% to 100%, and adjustable voltage dari 1.25V hingga 11.5V.
• Operasi Mesra Pengguna: Easy to operate with all parameters adjustable, making it accessible for users without extensive professional knowledge.

3. Kandungan Pakej

Selepas membongkar, sila sahkan bahawa semua item berikut disertakan:

• 1 x Irfora QDB-3A Ignition Coil Tester Unit
• 1 x Kabel Kuasa
• 3 x Test Connection Cables
• 3 x Single Plugs
• 1 x Idle Speed Stepper Motor Plug
• 1 x Stepper Motor Welding Cable

Figure 3.1: Irfora QDB-3A Ignition Coil Tester with its accessories.

4. Produk Lebihview dan Spesifikasi

4.1 Susun atur Peranti

The QDB-3A features a TFT color screen and clearly labeled controls for ease of use. Refer to the diagram below for an overview komponen dan kawalan peranti.

Figure 4.1: Front and bottom view of the QDB-3A tester with labeled controls and ports.

• TFT Color Screen: Displays operational parameters and measurement results.
• Increase/Reduce Frequency Buttons: Adjust the output frequency.
• Increase/Reduce Duty Buttons: Adjust the duty cycle.
• Step Motor Run Left/Right Buttons: Control the direction of stepper motor rotation.
• Suis Mod: Cycles through different operating modes.
• Regulate Output VoltagTombol e: Adjusts the VADJ output voltage.
• Voltage, Resistance Measurement Terminal: Input for multimeter functions.
• PWM Working Indicator: LED indicating PWM operation.
• Output Kuasa Boleh Laras: Pembolehubah voltagkeluaran e.
• PWM Signal Out: Output for PWM signals.
• Signal Out or DMM Measurement Ground: Common ground for signal output and multimeter.
• PWM Drive Negative Terminal: Negative terminal for PWM drive.
• Bekalan Kuasa Voltage Keluaran: Keluaran voltage equals the supply voltage.
• Stepper Motor Connector: Port for connecting stepper motors.
• DC Power In: Input untuk bekalan kuasa DC 9-26V.

4.2 Spesifikasi Teknikal

Figure 4.2: Specifications table and connection diagram for 3-wire signal drive mode.

5. Persediaan dan Operasi Asas

5.1 Sambungan Kuasa

1. Connect the provided power cable to the DC Power In port on the QDB-3A unit.
2. Connect the other end of the power cable to a 12V or 24V power source. Ensure the power source meets the device's requirements (9-26V / 100W).
3. The device will power on, and the TFT screen will display the main interface.

5.2 Mod Navigasi

Use the 'Mode Switch' button to cycle through the different operating modes available on the QDB-3A. The current mode will be displayed on the TFT screen.

6. Mod Operasi

6.1 PWM Drive Mode (2-wire Ignition Coil, Solenoid Valve, Injector, EGR)

This mode is used to drive and test 2-wire components such as ignition coils, solenoid valves, fuel injectors, and EGR valves.

1. Connect the component to be tested to the QDB-3A according to the diagram below. Ensure proper polarity.
2. Power the QDB-3A with a 12V or 24V supply.
3. Adjust the frequency of the PWM signal using the 'Increase/Reduce Frequency' buttons.
4. Adjust the duty cycle of the PWM signal using the 'Increase/Reduce Duty' buttons.
5. Check the screen to confirm that the set parameters are within the desired range.
6. Observe the working condition of the component to assess its quality.

Figure 6.1: Connection diagram for 2-wire power drive mode.

6.2 3-wire Signal Drive Mode

This mode is suitable for testing 3-wire components such as 3-wire ignition coils, 3-wire pump motors, and electronic fans.

1. Connect the component to be tested to the QDB-3A as shown in Figure 4.2.
2. Power the QDB-3A with a 12V or 24V supply.
3. Adjust the VPP (peak-to-peak voltage) of the PWM signal, which can be set between 5V and 12V for different components.
4. Adjust the frequency of the PWM signal.
5. Adjust the duty cycle of the PWM signal.
6. Verify the settings on the screen.
7. Observe the component's operation to determine its quality.

6.3 Step Motor Testing (Idle Motor, Instrument Motor, Headlight Motor)

Use this mode to test various stepper motors found in vehicles.

1. Connect the stepper motor to the QDB-3A using the stepper motor connector and appropriate cables, following the diagram below.
2. Power the QDB-3A with a 12V or 24V supply.
3. Click or long-press the 'Step Motor Run Left' or 'Step Motor Run Right' buttons to control the motor's rotation.
4. Observe the working condition of the stepper motor to judge its quality and functionality.

Figure 6.2: Connection diagram for step motor testing.

6.4 Signal Output Simulation

The QDB-3A can simulate Hall signals for various duty cycle sensors, including air conditioning pressure sensors, rail pressure sensors, and flow sensors. This function allows for testing ECU responses to sensor inputs.

• Connect the QDB-3A's PWM Signal Out to the ECU input for the sensor you wish to simulate.
• Adjust the frequency, amplitude, and duty ratio of the Hall signal using the corresponding controls on the device.
• Monitor the ECU's response to the simulated signal to diagnose sensor-related issues.

6.5 Multimeter Function (Resistance and Voltage Pengukuran)

The device includes a basic multimeter function for measuring resistance and voltage.

1. Power the QDB-3A with a 12V or 24V supply.
2. Connect the measuring probes to the Voltage, Resistance Measurement Terminal and the Signal Out/DMM Measurement Ground.
3. Connect the probes to the component or circuit you wish to measure. Ensure the voltage is not connected in reverse polarity.
4. Read the measurement value from the screen and interpret the results.

Figure 6.3: Connection diagram for resistance and voltage pengukuran.

7. Maklumat Keselamatan

To ensure safe operation and prevent damage to the device or connected components, please observe the following safety guidelines:

• Sentiasa pastikan volum bekalan kuasatage berada dalam julat 9-26V yang ditetapkan.
• The device is equipped with reverse connection protection. However, always double-check polarity before connecting to avoid potential issues.
• Overcurrent protection is integrated. If an overcurrent condition occurs, disconnect the device immediately and investigate the cause.
• Do not expose the device to extreme temperatures, moisture, or corrosive environments.
• Only use the provided cables and accessories or compatible replacements.
• Jauhkan peranti daripada kanak-kanak.

8. Penyelenggaraan

The Irfora QDB-3A Ignition Coil Tester requires minimal maintenance to ensure long-term performance:

• Pembersihan: Lap peranti dengan kain lembut dan kering. Jangan gunakan pembersih atau pelarut yang melelas.
• Storan: Simpan peranti di tempat yang sejuk dan kering jauh dari cahaya matahari langsung dan suhu yang melampau apabila tidak digunakan.
• Pemeriksaan Kabel: Periodically inspect all cables for signs of wear, damage, or fraying. Replace damaged cables immediately.

9. Penyelesaian masalah

If you encounter issues with your QDB-3A tester, consider the following basic troubleshooting steps:

• Peranti Tidak Dihidupkan: Pastikan kabel kuasa disambungkan dengan kukuh dan sumber kuasa membekalkan volum yang betultage (9-26V). Check the power source itself.
• Tiada Isyarat Output: Verify that the correct operating mode is selected and all parameters (frequency, duty cycle, voltage) are set appropriately for the component being tested. Check all connections.
• Pengukuran yang salah: For multimeter functions, ensure probes are correctly connected and making good contact. Verify the component being measured is functioning correctly.
• Component Not Responding: Double-check all connections to the component. Ensure the component itself is not faulty. Verify the QDB-3A's output parameters match the component's requirements.

If problems persist, consult the manufacturer's support resources or a qualified technician.

10. Waranti dan Sokongan

For information regarding product warranty, technical support, or service, please refer to the documentation provided with your purchase or contact Irfora customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.