BINGFU BFN00932

Bingfu Vehicle Mobile Ham Radio Antenna User Manual

model: BFN00932 | Jenama: BINGFU

1. Pengenalan

This manual provides essential information for the proper installation, operation, and maintenance of your Bingfu Vehicle Mobile Ham Radio Antenna. This dual-band antenna is designed for VHF (136-174MHz) and UHF (400-470MHz) frequencies, featuring a strong magnetic base for vehicle mounting and a soft whip design. Please read this manual thoroughly before use to ensure optimal performance and safety.

2. Kandungan Pakej

Sahkan bahawa semua item yang disenaraikan di bawah terdapat dalam pakej anda:

Complete Bingfu Ham Radio Antenna Kit with all components

Rajah 2.1: Complete antenna kit including the whip antenna, magnetic base, cable, adapters, ground planes, and hex tool.

3. Ciri-ciri Produk

Diagram showing antenna dimensions, flexible whip, and low loss RG58 cable

Rajah 3.1: Antenna dimensions and cable type. The antenna whip is flexible, and the cable is a low-loss RG58 type.

Close-up of the magnetic base with silicone gasket and strong magnet

Rajah 3.2: Details of the magnetic base, highlighting its strong magnetic hold and the protective silicone rubber gasket.

4. Persediaan & Pemasangan

4.1. Ground Plane Assembly

  1. Identify the central connector for the ground planes.
  2. Select the appropriate ground plane rods based on your operating frequency:
    • Gunakan short ground planes (9.5cm/3.74inch) for optimal performance on UHF (400-470MHz).
    • Gunakan long ground planes (15cm/5.9inch) for optimal performance on VHF (136-174MHz).
  3. Carefully screw the three selected ground plane rods into the designated ports on the central connector. Ensure they are finger-tight.
Ground plane kit components and assembly

Rajah 4.1: Ground plane kit showing the central connector and both short and long ground plane rods.

Diagram showing lengths of short and long ground planes for UHF and VHF

Rajah 4.2: Comparison of short (UHF) and long (VHF) ground plane rod lengths.

4.2. Perhimpunan Antena

  1. Screw the assembled ground plane unit onto the base of the antenna whip.
  2. Attach the antenna whip assembly to the magnetic base. Ensure a secure connection.

4.3. Vehicle Mounting

  1. Choose a flat, metallic surface on your vehicle, such as the roof or trunk lid, that is free from obstructions and provides a clear line of sight.
  2. Clean the chosen surface thoroughly to ensure maximum magnetic adhesion and to prevent scratching.
  3. Place the magnetic base firmly onto the cleaned metallic surface. The strong magnet will secure the antenna. The silicone gasket on the base helps protect your vehicle's paint.
  4. Route the 5m (16.4ft) RG58/U coaxial cable carefully to your radio, avoiding sharp bends, pinching, or interference with doors or windows.
Red truck with antenna mounted on the roof, illustrating easy installation

Rajah 4.3: Example of antenna placement on a vehicle roof for optimal signal.

4.4. Connecting to Your Radio

  1. The antenna cable terminates with a UHF PL259 Male Connector.
  2. If your radio has a UHF SO239 Female port, connect the PL259 Male connector directly.
  3. If your radio requires an SMA Female connection (common on handheld radios), use the provided SO239 to SMA Female Adapter. First, connect the PL259 Male to the SO239 side of the adapter, then connect the SMA Female side to your radio.
  4. Ensure all connections are tight to prevent signal loss.
Diagram showing SMA Male and PL259 Male connectors and their female counterparts on a radio

Rajah 4.4: Connector types and adapters for connecting the antenna to various mobile ham radios.

5. Operasi

Once installed and connected, your Bingfu antenna is ready for use. Ensure your radio is set to the correct frequency band (VHF or UHF) corresponding to the ground planes you have installed for optimal performance.

Person speaking into a ham radio with the antenna mounted on a vehicle, indicating clear communication

Rajah 5.1: The antenna facilitates clear communication for mobile radio users.

6. Penyelenggaraan

7. Penyelesaian masalah

MasalahKemungkinan PuncaPenyelesaian
Weak signal reception or transmission.
  • Incorrect ground plane rods installed for the frequency band.
  • Sambungan longgar atau berkarat.
  • Antenna not properly grounded (e.g., mounted on non-metallic surface).
  • High SWR.
  • Halangan menyekat isyarat.
  • Ensure correct ground planes are used (short for UHF, long for VHF).
  • Check all cable connections for tightness and cleanliness.
  • Mount antenna on a large metallic surface (vehicle roof/trunk).
  • Check SWR with a meter and adjust if necessary.
  • Relocate antenna to a clearer area.
Antenna falls off vehicle.
  • Insufficient magnetic adhesion.
  • Vehicle surface is dirty or uneven.
  • Excessive speed or strong winds.
  • Bersihkan permukaan pelekap dengan teliti.
  • Ensure the magnetic base is fully in contact with a flat metallic surface.
  • Reduce speed in high wind conditions.
Cable damage or wear.
  • Cable pinched by door/window.
  • Exposure to sharp edges or excessive friction.
  • Reroute cable to avoid pinching points.
  • Inspect cable regularly and replace if damaged.

8. Spesifikasi

CiriPerincian
Nombor ModelBFN00932
Julat KekerapanVHF: 136-174MHz, UHF: 400-470MHz
Jenis AntenaDual Band Mobile Ham Radio Antenna with Ground Planes
Panjang AntenaApproximately 42cm (16.53 inches) whip, 48.5cm (19.1 inches) total with base
Diameter Tapak Magnetik9cm (3.55 inci)
Jenis KabelRG58/U Coaxial Cable
Panjang Kabel5m (16.4 kaki)
Jenis PenyambungUHF PL259 Male
Impedans50 Ohm
warnaHitam
Berat Barang1.76 paun
Dimensi Produk (L x W x H)16.93 x 5.12 x 2.56 inci (berbungkus)

9. Maklumat Keselamatan

10. Waranti dan Sokongan

For warranty information or technical support, please refer to the documentation provided with your purchase or contact Bingfu customer service directly. Keep your purchase receipt as proof of purchase.

Pengeluar: Bingfu

ASIN: B0CLKLHHNP

Dokumen Berkaitan - BFN00932

Praview Bingfu RF Connector Usage Guidelines
Concise guidelines for the proper installation and use of Bingfu RF connectors to ensure optimal performance and longevity.
Praview Budget DIY GPS/GNSS Base Station / Receiver Setup With ESP32 and UM980
Learn how to build a cost-effective DIY GPS/GNSS base station or receiver using the ESP32 microcontroller and Unicorecomm UM980 module. This guide covers hardware, firmware, and configuration for creating a custom high-precision location system.
Praview Produktliste und Preise für Elektronik und Zubehör
Umfassende Liste von Elektronikprodukten und Zubehör mit detaillierten Preisinformationen. Entdecken Sie eine breite Palette von Marken und Artikeln, von Kopfhörern und Lautsprechern bis hin zu Computern und Mobiletelefonzubehör.