Manual Pengguna ESC ZTW Mantis G2 Siri 85A

1. Pengenalan

The ZTW Mantis G2 Series 85A Electronic Speed Controller (ESC) is an advanced 32-bit brushless speed controller designed for high-performance RC airplanes and fixed-wing aircraft. This ESC integrates a powerful 8A adjustable Switching BEC (SBEC) to provide stable power to your receiver and servos. It supports a wide range of battery configurations (3-8S LiPo/LiHV) and offers precise control and reliable operation for your aircraft's propulsion system.

Please read this manual thoroughly before installation and operation to ensure correct usage and maximize the performance and lifespan of your ESC.

2. Langkah-langkah Keselamatan

Improper use of the ESC can lead to personal injury and damage to the product or associated equipment. Always observe the following safety guidelines:

• Sambungan Bateri: Always connect the battery with correct polarity. Reverse polarity will cause immediate and irreversible damage to the ESC.
• Penebat: Pastikan semua sambungan ditebat dengan betul untuk mengelakkan litar pintas.
• Keselamatan Kipas: Always remove the propeller from the motor before performing any setup, testing, or maintenance to prevent accidental injury.
• haba: The ESC can generate significant heat during operation. Ensure adequate airflow for cooling and avoid touching it immediately after use.
• Air dan Kelembapan: Keep the ESC away from water, moisture, and conductive contaminants.
• Voltage Julat: Jangan melebihi vol input yang ditentukantage range (3-8S LiPo/LiHV).
• Kanak-kanak: This product is not a toy and is not suitable for children under 18 years of age without adult supervision.

3. Ciri-ciri Produk

• Advanced 32-bit microprocessor for precise control and rapid response.
• High-current capability: 85A continuous, 95A burst (10 seconds).
• Isi lebar voltage range: Supports 3-8S LiPo/LiHV batteries.
• Integrated 8A adjustable SBEC with selectable output voltages: 6V, 7.4V, or 8.4V.
• Designed specifically for RC airplane and fixed-wing applications.
• Multiple protection features including low-voltage cut-off, overheat protection, and throttle signal loss protection.
• Programmable via ZTW LCD Program Card G2 or dedicated Android/iOS mobile application.

4. Spesifikasi

5. Persediaan dan Pemasangan

Proper installation is crucial for the safe and efficient operation of your ESC. Follow these steps carefully:

1. Sambungan Motor: Connect the three motor wires (typically labeled A, B, C or U, V, W) from the ESC to the corresponding wires on your brushless motor. The order may affect motor rotation direction; this can be adjusted later if needed.
2. Sambungan Bateri: Connect the main power wires (red for positive, black for negative) from the ESC to your LiPo/LiHV battery. Ensure the connector type matches and polarity is correct.
3. Sambungan Penerima: Plug the throttle signal cable (usually a three-wire servo connector) from the ESC into the throttle channel (typically channel 3) of your RC receiver.
4. SBEC Jldtage Pemilihan: The Mantis G2 85A ESC features an adjustable SBEC. Refer to the programming section or the dedicated program card/app to set the desired output voltage (6V, 7.4V, or 8.4V) for your receiver and servos. Ensure the selected voltage is compatible with your receiver and servos.
5. Pemasangan: Securely mount the ESC in your aircraft, ensuring good airflow for cooling. Avoid mounting it in enclosed spaces without ventilation.

6. Arahan Operasi

Before first flight, it is essential to perform a throttle range calibration to ensure the ESC correctly interprets your transmitter's throttle stick positions.

6.1. Throttle Range Calibration

1. Turn on your transmitter and set the throttle stick to its maximum (full throttle) position.
2. Sambungkan bateri ke ESC. ESC akan mengeluarkan satu siri bunyi bip.
3. After the initial beeps, the ESC will detect the full throttle signal and emit a confirmation tone.
4. Move the throttle stick to its minimum (zero throttle) position. The ESC will emit another series of beeps, indicating the throttle range has been successfully calibrated.
5. The ESC is now ready for normal operation.

6.2. Operasi Biasa

After calibration, connect the battery with the throttle stick at minimum. The ESC will arm, indicated by a specific tone. You can then slowly advance the throttle to control the motor speed. Always ensure the propeller is clear before applying throttle.

7. Programming the ESC

The ZTW Mantis G2 85A ESC offers various programmable parameters to fine-tune its performance to your specific aircraft and preferences. Programming can be done using either the ZTW LCD Program Card G2 or the dedicated Android/iOS mobile application.

7.1. Programmable Parameters (Exampitu)

• Jenis Brek: Off, Soft, Medium, Hard.
• Masa: Low, Medium, High (adjusts motor efficiency and temperature).
• Potongan Voltage: Menetapkan voltage at which the ESC reduces or cuts power to protect the battery.
• Mod Permulaan: Normal, Soft, Super Soft.
• SBEC Jldtage: 6V, 7.4V, 8.4V.
• Putaran Motor: Normal, Reverse.

Refer to the specific instructions provided with the ZTW LCD Program Card G2 or within the mobile application for detailed steps on how to connect and adjust these parameters.

8. Penyelenggaraan

Regular inspection and basic maintenance will help ensure the longevity and reliable performance of your ESC:

• Pembersihan: Keep the ESC free from dust, dirt, and debris. Use a soft brush or compressed air to clean the heat sink fins.
• Semakan Sambungan: Periodically inspect all wire connections (motor, battery, receiver) for signs of wear, corrosion, or loose contacts.
• Kerosakan Fizikal: Check the ESC casing and wires for any physical damage after each flight.
• Storan: Store the ESC in a dry, cool environment away from direct sunlight and extreme temperatures.

9. Penyelesaian masalah

If you encounter issues with your ZTW Mantis G2 85A ESC, refer to the following common problems and solutions:

• Motor Tidak Berputar:
  • Periksa sambungan bateri dan tahap pengecasan.
  • Verify throttle signal cable is securely connected to the receiver.
  • Perform throttle range calibration again.
  • Ensure motor wires are correctly connected and not shorted.
• Motor Runs in Wrong Direction:
  • Swap any two of the three motor wires between the ESC and motor.
  • Alternatively, reverse motor direction using the programming options.
• ESC Overheats:
  • Ensure adequate airflow around the ESC.
  • Check if the propeller is too large or motor timing is too aggressive (adjust via programming).
  • Sahkan vol. bateritage and current draw are within specifications.
• Intermittent Power/Loss of Control:
  • Periksa semua sambungan untuk kelonggaran atau kakisan.
  • Inspect for damaged wires or solder joints.
  • Ensure receiver and transmitter are functioning correctly and within range.

10. Waranti dan Sokongan

For warranty information and technical support regarding your ZTW Mantis G2 Series 85A ESC, please contact the retailer or the manufacturer, ZTW, directly. For purchases made through Buddy RC, please reach out to Buddy RC customer service for assistance.

Simpan resit pembelian anda sebagai bukti pembelian untuk sebarang tuntutan waranti.