maXpeedingrods T6 Series Coilover Suspension Kit Instruction Manual

1. Pengenalan

This manual provides detailed instructions for the installation, adjustment, maintenance, and troubleshooting of your maXpeedingrods T6 Series Coilover Suspension Kit. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Produk Lebihview & Ciri-ciri

The maXpeedingrods T6 Series Coilover Suspension Kit is designed to enhance vehicle handling and appearance. Key features include:

• Kelengkapan Kenderaan: Specifically designed for Honda Accord LX, SE, LX-P sedan CP2 CP3 (2008-2012), Honda Accord LX, SE, LX-P coupe CS1 CS2 (2008-2012), Honda Accord LX, SE, LX-P sedan CU1 CU2 CU3 (2008-2015), Honda Accord Tourer 5-door wagon CW1 (2008-2015), and Acura TSX (2009-2015).
• Street Performance T6 Series: Optimized for street performance driving, balancing comfort, speed, and safety. Features an upgraded damper knob for easier adjustment and high-quality dampminyak dalam.
• 24 Tahap Boleh Laras Damping: Allows precise control over ride comfort and handling. Levels 0-8 are suggested for street use, 9-16 for mountain roads, and 17-24 for race tracks.
• Tinggi boleh laras: Provides 1-3 inches of height adjustment for a more aggressive stance and improved steering response.
• Kadar Musim Bunga: Front: 10 kg/mm (560 lbs/in); Rear: 7 kg/mm (392 lbs/in). High tensile performance springs are stress-tested over 600,000 times with minimal distortion.
• Pembinaan Tahan Lama: Features upgraded full aluminum plates, 22mm front rod diameter for long-lasting rod lifetime, high rigid piston rod, 6061-T6 AL perch, anodized shock body with galvanized anti-corrosion coating, and matte finish lower mount.

3. Spesifikasi

4. Maklumat Keselamatan

Suspension installation requires specialized tools and knowledge. Improper installation can lead to serious injury or vehicle damage. It is highly recommended that installation be performed by a certified professional mechanic. Always wear appropriate personal protective equipment (PPE) during installation. Ensure the vehicle is securely supported on jack stands or a lift before beginning any work.

5. Panduan Pemasangan

This section outlines the general steps for installing the maXpeedingrods T6 Series Coilover Kit. Refer to the included installation instructions for your specific vehicle model for detailed torque specifications and procedures.

5.1. Pra-Pemasangan

1. Gather all necessary tools as listed in your product packaging.
2. Letakkan kenderaan pada permukaan yang rata dan gunakan brek letak kereta.
3. Loosen the lug nuts on the wheels to be removed.
4. Lift the vehicle using a hydraulic lift or jack stands, ensuring it is stable and secure.
5. Keluarkan roda.

5.2. Front Coilover Installation

1. Remove the brake hose mount and sensor clip from the old strut assembly.
2. Loosen and remove the knuckle bolts connecting the old strut to the knuckle.
3. Open the hood and secure it. Remove the access panel from the cowl to expose the upper strut mounts.
4. Remove the upper nuts securing the old strut to the vehicle chassis.
5. Tanggalkan pemasangan strut lama dari kenderaan dengan berhati-hati.
6. Install the new maXpeedingrods front coilover assembly. Hand-start the new hardware for the upper mount.
7. Tighten the top mount nuts to 60 Nm (45 ft-lb) of torque.
8. Lift the vehicle and insert the knuckle into the bottom of the new coilover.
9. Reuse the old hardware to secure the knuckle bolts and tighten to 130 Nm (95 ft-lb) of torque.
10. Secure the brake hose and sensor clip to the new coilover.
11. Reinstall the access panel and remount the weather seal.

5.3. Rear Coilover Installation

1. Loosen the lug nuts on the rear wheels and lift the vehicle. Remove the rear wheels.
2. Open the trunk. Remove the trunk mat, foam pad, and side carpet liner clips to access the upper shock absorber hardware.
3. Remove the upper shock absorber hardware.
4. Keluarkan perkakasan kejutan bawah.
5. Remove the old shock absorber and rear spring.
6. Install the new maXpeedingrods rear coilover spring with the adjuster plate.
7. When installing the new rear shock, remove the damping adjustment cap using the provided small hex key. Remove the new hardware and reuse the original upper bushing.
8. Install the new shock absorber and secure the lower bolt. Tighten to 80 Nm (60 ft-lb) of torque.
9. Lower the vehicle to attach the upper shock from inside the trunk. Place the original bushing over the shock mount, then the washer and the nut.
10. Tighten the upper nut with a 17mm socket.
11. Pasang semula damping adjustment topper.
12. Reassemble the trunk interior: carpet liner, foam parts, and plastic loading guard.

5.4. Selepas Pemasangan

1. Reinstall the wheels. Hand-start lug nuts, then use a 17mm socket to secure them. Torque lug nuts to 130 Nm (95 ft-lb) of torque.
2. Turunkan kenderaan sepenuhnya.
3. Perform a test drive to check for any unusual noises or handling characteristics.
4. It is highly recommended to get a professional wheel alignment after installing new suspension components.

5.5. Assembly and Overview Video

6. Adjustment Guide

6.1. Damping Adjustment (24 Levels)

Coilovers mempunyai 24 tahap damping force adjustment, allowing you to fine-tune your ride for various conditions. The adjustment knob is located at the top of the coilover.

• Tahap 0-8: Recommended for comfortable street driving.
• Tahap 9-16: Suitable for mountain roads or more spirited driving.
• Tahap 17-24: Designed for track use, offering maximum stiffness and control.

6.2. Pelarasan Ketinggian

The coilovers allow for 1-3 inches of ride height adjustment. This is achieved by rotating the lower mount on the threaded shock body. Use the provided spanner wrenches to loosen the locking collars, adjust the height, and then re-tighten the collars securely.

7. Penyelenggaraan

Penyelenggaraan tetap memastikan jangka hayat dan prestasi optimum coilovers anda.

• Pemeriksaan Berkala: Periodically inspect the coilovers for any signs of damage, leaks, or loose components. Check for wear on bushings and mounts.
• Pembersihan: Keep the coilovers clean from dirt, salt, and debris, especially the threaded sections. Use mild soap and water, then rinse thoroughly.
• Pelinciran: Apply a thin layer of anti-seize lubricant to the threads of the coilover body and locking collars to prevent seizing and facilitate future adjustments.
• But Habuk: Ensure the full-length dust boots are intact and properly seated to protect the piston rod from contaminants.

8. Penyelesaian masalah

Jika anda mengalami masalah dengan gegelung anda, pertimbangkan masalah dan penyelesaian biasa berikut:

• Bunyi Luar Biasa (Clunking/Decit):
  • Periksa semua bolt pemasangan untuk tork yang betul.
  • Inspect bushings for wear or damage.
  • Ensure spring seats and locking collars are tight.
• Kualiti Tunggangan yang Buruk (Terlalu Kaku/Terlalu Lembut):
  • Laraskan damping settings according to Section 6.1.
  • Verify spring preload is set correctly.
• Ketinggian Tunggangan Tidak Sekata:
  • Re-measure and adjust ride height on all four corners as per Section 6.2.
  • Ensure locking collars are securely tightened after adjustment.
• Penyerap Hentakan Bocor:
  • A small amount of oil residue is normal. Excessive oil leakage indicates a seal failure. Contact customer support for assistance.

9. Waranti dan Sokongan

For warranty information, technical support, or any questions regarding your maXpeedingrods T6 Series Coilover Suspension Kit, please refer to the warranty card included in your product packaging or visit the official maXpeedingrods website. Always provide your model number (KJ699) and purchase details when contacting support.