Directed Electronics Plug & Play Remote Starter with T-Harness

pengenalan

This manual provides comprehensive instructions for the installation and operation of your Directed Electronics Plug & Play Remote Starter with T-Harness. This system is designed for select Ford vehicles manufactured between 2009 and 2016. It features a no-cut, no-splice T-harness for an OEM-like installation and is compatible with both manual transmission modes and gas/diesel engines. The module comes pre-loaded with Firmware 800.FORD6.

Nota Penting: Professional installation is recommended. Some vehicles may require additional parts not included in this package. Please confirm compatibility with your vehicle prior to installation.

Maklumat Keselamatan

• Ensure the vehicle is parked on a level surface with the parking brake engaged before beginning installation.
• Putuskan sambungan bateri kenderaan sebelum melakukan sebarang kerja elektrik untuk mengelakkan kejutan elektrik atau kerosakan pada sistem elektrik kenderaan.
• Sentiasa pakai peralatan perlindungan diri yang sesuai, seperti cermin mata keselamatan dan sarung tangan.
• Verify all connections are secure and correctly routed to prevent interference with vehicle operation.
• Do not attempt to start the vehicle with the remote starter if any warning lights are illuminated on the dashboard, or if there are any unusual noises or smells.
• Keep children and pets away from the vehicle during remote start operation.

Kandungan Pakej

Verify all items are present before beginning installation:

• Directed Electronics Remote Starter Module
• T-Harness (no cut, no splice)
• Installation Guide (physical or digital)

Image: The remote starter module, T-harness, and product packaging. The module is a black rectangular device, and the T-harness consists of various wires and connectors designed for plug-and-play installation.

Panduan Pemasangan

Follow these steps carefully for proper installation. Refer to the provided videos for visual guidance.

Step 1: Access the OBD-II Port and Steering Column

Locate the OBD-II port, typically found under the dashboard on the driver's side. You may need to remove trim panels around the steering column to access the necessary wiring harnesses.

Step 2: Connect the T-Harness

The T-harness is designed for plug-and-play installation. Disconnect the existing harness from the vehicle's OBD-II port or gateway module, then connect the T-harness in-line. Ensure all connections are firmly seated.

Step 3: Connect the Remote Starter Module

Connect the T-harness to the remote starter module. Ensure the module is securely connected to the harness.

Step 4: Module Programming

The module requires programming to synchronize with your vehicle. Follow the specific programming steps outlined in the detailed installation guide provided with your product. This typically involves pressing a button on the module while cycling the vehicle's ignition.

General Programming Sequence:

1. Press and hold the programming button on the module.
2. Connect the black connector to the module while holding the button.
3. Release the button when the blue LED is momentarily lit.
4. Connect the white connector to the module.
5. Insert the vehicle key into the ignition (do not start the engine).
6. Turn the ignition to the ON position. The module's LEDs will indicate programming status (e.g., blue LED turns off, red and yellow LEDs turn on).
7. Wait for the blue LED to flash, then turn the ignition OFF. All LEDs should turn off.
8. Turn the ignition ON again. The yellow LED should come on.
9. Wait 5 seconds, then turn the ignition OFF. All LEDs should go off.
10. Modul itu kini diprogramkan.

Arahan Operasi

Once installed and programmed, your remote starter can be operated using your vehicle's factory key fob.

Urutan Mula Jauh

To remote start your vehicle, press the LOCK button on your factory key fob three times in quick succession (LOCK, LOCK, LOCK). The vehicle's engine should start.

Remote Stop Sequence

To turn off the engine after a remote start, press the LOCK button on your factory key fob three times in quick succession (LOCK, LOCK, LOCK) again, or simply press the brake pedal inside the vehicle.

"No Honk" Programming (if applicable)

Some models allow for a "No Honk" remote start/stop feature. Refer to the video below for programming instructions specific to select KR-RS models.

Penyelenggaraan

The Directed Electronics Remote Starter is designed for maintenance-free operation. Ensure all connections remain secure and free from moisture or debris. Periodically check the wiring for any signs of wear or damage.

Menyelesaikan masalah

• Remote starter does not activate:
  • Ensure all doors, hood, and tailgate are closed.
  • Verify the vehicle's battery is charged.
  • Re-check all T-harness connections.
  • Confirm the module was programmed correctly. Repeat the programming steps if necessary.
• Vehicle starts but immediately shuts off:
  • This may indicate an issue with the module's programming or vehicle compatibility. Refer to the detailed installation guide or contact support.
• Tingkah laku yang tidak dijangka:
  • If the system exhibits unexpected behavior, disconnect the module and contact technical support.

Spesifikasi

Waranti dan Sokongan

For warranty information, technical support, or to confirm vehicle compatibility, please contact Directed Electronics customer service or refer to the official product website. It is recommended to reflash the firmware prior to installation for optimal performance.

Note: Some vehicles may require extra parts which are not included and sold separately.