FLOWPAC FX701

FLOWPAC DC 12V 1500 GPH Utility Submersible Sump Pump with Switch Instruction Manual

Model: FX701

1. Pengenalan

This manual provides essential information for the safe and efficient operation of your FLOWPAC DC 12V 1500 GPH Utility Submersible Sump Pump. Please read these instructions carefully before installation and use, and retain them for future reference. This pump is designed for various water transfer applications, operating with a 12-volt DC power source.

2. Maklumat Keselamatan

3. Kandungan Pakej

Sahkan bahawa semua item ada dan tidak rosak semasa membuka bungkusan:

4. Spesifikasi

FLOWPAC FX701 Submersible Pump with specifications table

Image: The FLOWPAC FX701 pump shown alongside a table detailing its technical specifications.

CiriPerincian
ModelFX701
Voltage12V DC
Nilai Semasa13.5 A
Maks. Kadar aliran1500 GPH (Gelen Sejam)
Max. Head (Lifting Height)25 Kaki
Kelajuan Putar6000 r/m
Pengendalian Pepejal1/8 Inci
Pelepasan1-1/4" NPT, 3/4" Garden hose adapter included
Sumber KuasaDC (Battery not included)
bahanTermoplastik
Berat Barang7.48 paun
Wattage170 watt
Diagram of FLOWPAC FX701 pump with labeled components and dimensions

Image: A detailed diagram of the pump, highlighting components such as the discharge, handle, power clip, intake screen, and switch, along with key dimensions.

5. Persediaan

5.1. Penempatan Pam

Install the pump on a hard, level surface within the water. To prevent clogging and damage, avoid placing the pump directly in mud, sand, silt, or on rocky surfaces. If necessary, use bricks or patio blocks to elevate the pump off the bottom.

5.2. Sambungan Hos

Connect a discharge hose to the pump's outlet. You can use the provided 3/4" garden hose adapter or another suitable hose fitting (sold separately). For optimal performance and to minimize friction loss, ensure the hose diameter is 3/4" or larger.

5.3. Sambungan Bateri

Connect the battery alligator clips to a 12-volt DC battery (battery not included). Ensure correct polarity:

Diagram showing pump installation and battery connection steps

Image: A visual guide illustrating the steps for pump installation in water and connecting the battery clips to a 12V battery.

6. Operasi

  1. Once the pump is correctly placed and connected to the battery and discharge hose, turn on the pump power switch located on the cord.
  2. The pump will begin operating, effectively removing water down to approximately 1/8" to 1/4" from the surface.
  3. Penting: Do not allow the pump to run dry. The pump relies on water for cooling and internal lubrication. Continuous dry operation will lead to motor overheating and permanent damage.
  4. This pump features an anti-airlock hole. A small stream of water will be visible from this hole during operation. This is normal and indicates proper function. Periodically inspect and clean this hole to prevent airlock issues.
  5. When pumping is complete, turn off the power switch.
FLOWPAC pump operating in water, discharging water

Image: The FLOWPAC submersible pump actively pumping water from a container, showing the discharge stream.

6.1. Aplikasi Biasa

This versatile pump is suitable for a wide range of applications, including:

Diagram showing various applications for the submersible pump

Image: A graphic illustrating diverse uses for the pump, such as in homes, outdoors, basements, pools, flat roofs, and for camping/RV.

7. Penyelenggaraan

Penyelenggaraan yang kerap memastikan jangka hayat dan prestasi optimum pam anda.

8. Penyelesaian masalah

MasalahKemungkinan PuncaPenyelesaian
Pam tidak bermula atau berjalan sekejap-sekejap.
  • No power or low battery voltage.
  • Sambungan bateri longgar atau berkarat.
  • Suis kuasa dimatikan.
  • Masalah motor dalaman.
  • Periksa cas bateri dan voltage (must be 12V DC).
  • Clean and tighten battery alligator clips.
  • Pastikan suis kuasa berada dalam kedudukan "ON".
  • Jika masalah berterusan, hubungi sokongan pelanggan.
Pam berjalan tetapi tiada air yang dikeluarkan atau alirannya rendah.
  • Intake screen is clogged.
  • Discharge hose is kinked, blocked, or too small.
  • Anti-airlock hole is clogged.
  • Pump is running dry (not fully submerged).
  • Excessive discharge head (pumping too high).
  • Disconnect power and clean the intake screen.
  • Inspect and clear the discharge hose; ensure it's 3/4" or larger.
  • Clean the anti-airlock hole.
  • Pastikan pam terendam sepenuhnya di dalam air.
  • Reduce the vertical lift if possible.
Pam mengeluarkan bunyi yang luar biasa.
  • Debris in the pump impeller.
  • Pam kering.
  • Internal component wear.
  • Disconnect power and inspect for debris.
  • Pastikan pam terendam sepenuhnya.
  • Jika bunyi bising berterusan, hubungi sokongan pelanggan.

9. Waranti dan Sokongan

The FLOWPAC DC 12V 1500 GPH Utility Submersible Sump Pump comes with a one-year warranty from the date of purchase. This warranty covers manufacturing defects under normal use conditions.

Sila ambil perhatian: Defects or damages resulting from improper use, misuse, neglect, unauthorized modifications, or operation without water (dry running) are not covered under this warranty.

For technical assistance, warranty claims, or any questions regarding your product, please contact FLOWPAC customer support. Refer to your purchase documentation for specific contact details or visit the official FLOWPAC webtapak.

Dokumen Berkaitan - FX701

Praview Manual Pengguna dan Panduan Pemasangan Penerima Kaset JVC KS-FX701/KS-FX601/KS-F501
This document provides comprehensive instructions for the JVC KS-FX701, KS-FX601, and KS-F501 Cassette Receivers, covering basic operations, radio and tape functions, sound adjustments, remote control, CD changer integration, external component connection, maintenance, troubleshooting, and detailed installation procedures.