Manual Pengguna Gergaji Rantai Pemegang Belakang Gas Komersial ECHO CS-3510

Produk Selesaiview

The ECHO CS-3510 is a commercial-grade gas-powered rear handle chain saw designed for various cutting tasks. Its 34.4cc engine provides substantial power, making it suitable for storm clean-up, light firewood cutting, limb trimming, and felling trees up to 28 inches in diameter. The design prioritizes user comfort and productivity with its lighter weight and efficient power delivery.

Image: The ECHO CS-3510 Chain Saw, showcasing its orange and black design with a 16-inch bar.

Ciri-ciri Utama:

• 34.4cc commercial grade gas engine for reliable power.
• Optimized weight for reduced operator fatigue and increased productivity.
• i-30 starter system designed to reduce starting effort by 30%.
• 3-point spring vibration reduction system for enhanced operator comfort during extended use.
• Air injection air cleaner system for improved air filtration and reduced maintenance requirements.

Panduan Persediaan

1. Membongkar dan Pemeriksaan Awal

Carefully remove all components from the packaging. Inspect the chain saw for any signs of damage that may have occurred during shipping. Ensure all parts listed in the packing list are present.

2. Fuel and Oil Mixture Preparation

The ECHO CS-3510 requires a specific fuel mixture. Use fresh, unleaded gasoline with an octane rating of 89 or higher, mixed with a high-quality 2-stroke engine oil at a ratio specified in the separate engine manual (typically 50:1). Always mix fuel in a clean, approved fuel container.

3. Pemasangan Bar dan Rantai

1. Letakkan gergaji rantai di atas permukaan yang rata dan stabil.
2. Remove the chain cover by loosening the two nuts.
3. Carefully position the chain around the clutch drum and guide bar, ensuring the cutting edges of the chain are facing the correct direction (refer to directional arrows on the chain).
4. Slide the guide bar onto the studs, aligning the chain with the groove in the bar.
5. Replace the chain cover and hand-tighten the nuts.
6. Adjust chain tension using the tensioning screw. The chain should be snug against the bar but still able to be pulled freely by hand.
7. Fully tighten the chain cover nuts.

Imej: Sebelah view of the ECHO CS-3510 Chain Saw, illustrating the guide bar and chain assembly.

4. Filling Fuel and Chain Oil Tanks

Fill the fuel tank with the prepared fuel mixture. Fill the chain oil tank with high-quality bar and chain lubricant. Do not overfill. Ensure caps are securely tightened.

Arahan Operasi

1. Pemeriksaan Pra Operasi

• Sahkan ketegangan rantai adalah betul.
• Periksa paras bahan api dan minyak rantai.
• Inspect the chain for sharpness and damage.
• Pastikan semua nat dan bolt ketat.
• Confirm the chain brake is disengaged before starting.

2. Menghidupkan Enjin (Permulaan Sejuk)

1. Place the chain saw on a firm, flat surface.
2. Pasang brek rantai.
3. Gerakkan tuil tercekik ke kedudukan TERCIK PENUH.
4. Press the primer bulb 5-7 times until fuel is visible.
5. Pull the starter handle firmly and smoothly until the engine "pops" or attempts to start.
6. Move the choke lever to the HALF CHOKE or RUN position.
7. Pull the starter handle again until the engine starts.
8. Allow the engine to warm up for a few moments before disengaging the chain brake and beginning operation.

3. Starting the Engine (Warm Start)

For a warm engine, move the choke lever directly to the RUN position and pull the starter handle until the engine starts.

4. Basic Cutting Techniques

• Always maintain a firm grip with both hands on the handles.
• Stand with your feet shoulder-width apart for stability.
• Elakkan memotong dengan hujung bar panduan untuk mengelakkan sogokan.
• Plan your cuts to ensure the wood falls safely and away from you.
• Be aware of pinching hazards when cutting through logs under tension.

5. Menghentikan Enjin

To stop the engine, move the ignition switch to the "OFF" position. Engage the chain brake for safety when not actively cutting.

Jadual Penyelenggaraan

Regular maintenance is crucial for the longevity and safe operation of your ECHO CS-3510 chain saw.

Daily Maintenance (Before Each Use):

• Periksa ketajaman dan ketegangan rantai.
• Inspect guide bar for wear and burrs.
• Verify chain oiler is functioning.
• Clean debris from air filter and cooling fins.
• Periksa semua pengikat sama ada ketat.

Weekly Maintenance (or Every 10 Operating Hours):

• Bersihkan atau ganti penapis udara.
• Clean spark plug and check gap. Replace if necessary.
• Clean clutch area and chain brake mechanism.
• Inspect fuel filter.
• Rotate guide bar to ensure even wear.

Mengasah rantai:

Rantai yang tajam adalah penting untuk pemotongan yang selamat dan cekap. Asah rantai secara berkala menggunakan mata gerudi bulat file of the correct diameter (refer to your chain's specifications) and a flat file for depth gauges. Alternatively, have the chain professionally sharpened.

Pembersihan Penapis Udara:

Remove the air filter cover and carefully remove the air filter. Clean it with warm, soapy water, rinse thoroughly, and allow it to air dry completely before reinstallation. For heavily soiled filters, replacement may be necessary.

Menyelesaikan masalah

Spesifikasi Teknikal

Waranti dan Sokongan

ECHO products are manufactured to high standards and are backed by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official ECHO webtapak.

For technical assistance, parts, or service, please contact an authorized ECHO service dealer. You can find a dealer near you by visiting the ECHO website or contacting their customer support line.

Penting: Always provide your product model number (CS-3510-16) and serial number when seeking support.