TURCK NI6U-EG08-AP6X-H1341 Proximity Sensor User Manual

1. Pengenalan

This manual provides essential information for the safe and efficient installation, operation, and maintenance of the TURCK NI6U-EG08-AP6X-H1341 Proximity Sensor. Please read all instructions carefully before proceeding with installation or operation to ensure proper function and prevent damage.

2. Arahan Keselamatan

• Always disconnect power to the circuit before installing, wiring, or servicing the sensor.
• Pemasangan dan penyelenggaraan hendaklah hanya dilakukan oleh kakitangan yang berkelayakan yang biasa dengan sistem elektrik dan prosedur keselamatan.
• Observe all local, national, and international electrical codes and regulations.
• Jangan melebihi vol operasi yang ditetapkantage atau penilaian semasa.
• Protect the sensor from mechanical damage, excessive vibration, and extreme temperatures outside its specified operating range.

3. Produk Lebihview

The TURCK NI6U-EG08-AP6X-H1341 is an UPROX M8x1 barrel-type inductive proximity sensor. It is designed for non-contact detection of metallic objects within its sensing range. This sensor features an extended 6mm sensing range, a 3-wire DC PNP output configuration, and operates on a 10-30VDC power supply. Electrical connection is made via an M12 male connector.

Image 1: TURCK NI6U-EG08-AP6X-H1341 Proximity Sensor. This image shows the M8x1 barrel-shaped sensor with its M12 male connector.

4. Persediaan

4.1. Pemasangan

1. Select a mounting location where the sensor's sensing face can reliably detect the target object without obstruction.
2. Ensure the sensor is securely fastened using appropriate mounting hardware for M8x1 barrel sensors.
3. Maintain sufficient clearance around the sensor body, especially if it is a non-flush mount type, to prevent interference from surrounding metal. For flush-mountable sensors, ensure the sensing face is flush with the mounting surface.

4.2. Pendawaian

Connect the sensor to the control system according to the following wiring diagram for a 3-wire DC PNP sensor with an M12 connector:

• Pin 1 (Brown wire): +10-30 VDC (Power Supply Positive)
• Pin 3 (Blue wire): 0 VDC (Power Supply Negative / Ground)
• Pin 4 (Black wire): PNP Output (Switching signal to load)

Ensure all connections are tight and properly insulated. Verify the power supply voltage is within the specified 10-30VDC range.

5. Arahan Operasi

Once properly installed and wired, the TURCK NI6U-EG08-AP6X-H1341 sensor operates automatically. When a metallic object enters the sensor's 6mm sensing field, the PNP output (black wire) will switch from its OFF state to its ON state (supplying positive voltage to the load). When the metallic object leaves the sensing field, the output will return to its OFF state. The UPROX technology ensures consistent sensing performance across various metal types without requiring correction factors.

6. Penyelenggaraan

The TURCK NI6U-EG08-AP6X-H1341 proximity sensor is designed for long-term, maintenance-free operation. However, periodic checks can help ensure optimal performance:

• Keep the sensing face clean and free from excessive dirt, dust, or metallic debris.
• Inspect the M12 connector and wiring for any signs of damage, corrosion, or loose connections.
• Ensure the sensor remains securely mounted and its position has not shifted.

There are no user-serviceable parts inside the sensor. Do not attempt to open or repair the device.

7. Penyelesaian masalah

8. Spesifikasi

• model: NI6U-EG08-AP6X-H1341
• Jenis Sensor: Inductive Proximity Sensor, UPROX
• Housing Style: M8x1 Barrel
• Julat Sensing: 6 mm
• Jenis Output: 3-wire DC PNP, Normally Open (NO)
• Vol Operasitage: 10-30 VDC
• Sambungan: Penyambung Lelaki M12
• Penilaian Perlindungan: Typically IP67 (Dust tight and protected against immersion up to 1m)
• Suhu Operasi: -25°C to +70°C (Typical industrial range)

9. Waranti dan Sokongan

For detailed warranty information, technical support, or service inquiries regarding your TURCK NI6U-EG08-AP6X-H1341 Proximity Sensor, please refer to the official TURCK website or contact their authorized customer support channels. Keep your purchase documentation for warranty claims.

TURCK Official Webtapak: www.turck.com