1. Produk Lebihview
The Ozito Air Spray Gun (Model: 4472350) is a versatile tool designed for efficient application of various coatings. Its suction-feed design and adjustable controls make it suitable for a wide range of painting tasks, from general-purpose spraying to applying specific finishes and sealants. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting.
Figure 1: Ozito Air Spray Gun with attached 1000 ml paint pot.
2. Maklumat Keselamatan
Sentiasa patuhi langkah berjaga-jaga keselamatan asas untuk mengurangkan risiko kebakaran, kejutan elektrik dan kecederaan diri apabila menggunakan produk ini.
- Baca Manual: Thoroughly read and understand all instructions before operating the spray gun.
- Alat Pelindung Diri (PPE): Always wear appropriate eye protection (safety glasses/goggles), respiratory protection (respirator mask), and protective gloves.
- Pengudaraan: Use the spray gun in a well-ventilated area to avoid inhalation of fumes and to prevent the buildup of flammable vapors.
- Bahan mudah terbakar: Do not spray flammable or combustible materials near open flames, pilot lights, or other ignition sources.
- Keselamatan Elektrik: Ensure your air compressor and any extension cords are properly grounded and rated for the power requirements.
- Jauhkan Kanak-kanak: Do not allow children or untrained persons to operate the spray gun.
- Sambungan Selamat: Ensure all air hose connections are secure before operation.
3. Komponen dan Bahagian
The Ozito Air Spray Gun comes with the following main components:
- Suction Spray Gun Body
- 1.5 mm Nozzle (pre-installed or included)
- 1000 ml Paint Pot (Suction Cup)
- Fluid Adjustment Dial
- Fan Adjustment Dials
- Penyambung Masuk Udara
Rajah 2: Sisi view of the Ozito Air Spray Gun, showing the handle and air inlet.
4. Persediaan
- Bongkar: Keluarkan semua komponen dari pembungkusan dengan berhati-hati. Periksa untuk sebarang kerosakan.
- Connect Air Compressor: Attach a suitable air hose (not included) from your air compressor to the air inlet connector on the spray gun. Ensure the compressor can provide a minimum flow rate of 85 liters per minute.
- Sediakan Bahan: Prepare your paint, topcoat, or sealant according to the manufacturer's instructions. Ensure it is properly thinned for spraying consistency.
- Fill Paint Pot: Unscrew the paint pot from the spray gun body. Fill the pot with your prepared material, ensuring not to overfill. Reattach the paint pot securely to the spray gun.
- Pelarasan Awal: Before spraying, make initial adjustments to the fluid and fan pattern dials. Start with a moderate setting.
5. Arahan Operasi
- Power On Compressor: Turn on your air compressor and allow it to build up sufficient pressure.
- Corak Semburan Ujian: Before spraying your actual workpiece, test the spray pattern on a piece of scrap material. Adjust the fluid adjustment dial to control the amount of material sprayed and the fan adjustment dials to change the spray pattern (e.g., from a round to a flat pattern).
- Teknik Penyemburan: Hold the spray gun perpendicular to the surface, maintaining a consistent distance (typically 6-10 inches). Use smooth, even strokes, overlapping each pass by about 50%. Release the trigger at the end of each stroke.
- Pengisian semula: If the paint pot runs low, turn off the air supply, unscrew the pot, refill, and reattach before resuming.
6. Penyelenggaraan
Pembersihan dan penyelenggaraan yang betul adalah penting untuk jangka hayat dan prestasi pistol semburan anda.
- Pembersihan Segera: Clean the spray gun immediately after each use. Do not allow material to dry inside the gun.
- Pembongkaran: Disassemble the paint pot, nozzle, and air cap.
- Komponen Pembersihan: Clean all components thoroughly with an appropriate cleaning solution (e.g., paint thinner for oil-based paints, water for water-based paints). Use a cleaning brush to remove any residue from the nozzle and internal passages.
- Pemasangan semula: Reassemble the spray gun once all parts are clean and dry.
- Storan: Store the spray gun in a clean, dry place, away from extreme temperatures and direct sunlight.
7. Penyelesaian masalah
| Masalah | Kemungkinan Punca | Penyelesaian |
|---|---|---|
| Tiada semburan atau semburan lemah | Clogged nozzle or air cap; insufficient air pressure; material too thick. | Clean nozzle and air cap; check compressor pressure; thin material. |
| Corak semburan tidak sekata | Dirty air cap; damaged nozzle; incorrect fan adjustment. | Clean air cap; replace nozzle if damaged; adjust fan dials. |
| Material spitting | Material too thick; air leak; low material in pot. | Thin material; check connections for leaks; refill paint pot. |
8. Spesifikasi
- Nama Model: ASG-SFEU; EX; UK
- Nombor Model Item: 4472350
- Jenama: Ozito
- Saiz muncung: 1.5 mm
- Paint Pot Capacity: 1000 ml
- Minimum Air Compressor Flow Rate: 85 liter seminit
- warna: Kelabu
- Komponen yang Disertakan: 1 suction spray gun
- Dimensi Pakej: 28.5 x 19 x 11 cm
- Berat Barang: 790 gram
- Pengeluar: Einhell
9. Waranti dan Sokongan
For information regarding warranty coverage, spare parts availability, or technical support, please refer to the official Ozito website or contact Ozito customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.
Sumber Dalam Talian: melawat www.ozito.com.au (or your regional Ozito website) for product registration, FAQs, and support contact details.
