HUBBELL 7051-G Receptacle Instruction Manual

pengenalan

This manual provides essential instructions for the safe installation, operation, and maintenance of the Hubbell 7051-G 15A, 125V-AC, 2-Pole, 3-Wire Receptacle. Please read this manual thoroughly before installation and retain it for future reference. Proper installation by a qualified electrician is recommended.

Maklumat Keselamatan

AMARAN: Risk of electric shock or fire. Improper installation can result in serious injury or death. Always turn off power at the circuit breaker or fuse box before installing or servicing this device. Use only copper wire with this device. Do not use with aluminum wire unless specifically rated for it. Ensure all connections are tight and secure.

• Sentiasa putuskan sambungan kuasa sebelum bekerja pada litar elektrik.
• Rujuk juruelektrik yang berkelayakan jika anda tidak pasti tentang mana-mana bahagian proses pemasangan.
• Ikuti semua kod elektrik tempatan dan nasional.
• Jangan melebihi penarafan elektrik peranti yang ditentukan.

Produk Selesaiview

The Hubbell 7051-G is a 15 Amp, 125 Volt, 2-pole, 3-wire grounding duplex receptacle designed for general-purpose electrical applications. It features a durable nylon construction and is suitable for various residential and commercial installations.

Imej: Depan view of the Hubbell 7051-G duplex receptacle, showing two outlets with grounding slots.

Persediaan dan Pemasangan

Alat yang Diperlukan: Screwdriver (Phillips and/or flathead), Wire Strippers, Voltage Penguji.

1. Matikan Kuasa: Locate the circuit breaker or fuse that controls the outlet you are working on and turn it off. Verify power is off using a voltage penguji.
2. Keluarkan Bekas Lama (jika berkenaan): Unscrew the wall plate and then the mounting screws holding the old receptacle in the electrical box. Carefully pull the receptacle out and disconnect the wires.
3. Sediakan Wayar: Strip approximately 1/2 inch of insulation from the ends of the circuit wires. Ensure the wire ends are clean and straight.


Imej: Sisi view of the Hubbell 7051-G receptacle, showing the strip gauge for proper wire preparation.

4. Sambung wayar:
   • Green or Bare Copper Wire (Ground): Connect to the green grounding screw.
   • White Wire (Neutral): Connect to the silver screw.
   • Black or Red Wire (Hot/Live): Connect to the brass screw.
   Ensure wires are securely wrapped around the screws in a clockwise direction and tightened firmly.

Imej: Belakang view of the Hubbell 7051-G receptacle, illustrating the screw terminals for wiring connections (brass for hot, silver for neutral, green for ground).


Image: Close-up of the rear of the Hubbell 7051-G receptacle, detailing the wire strip gauge and voltage ratings (15A, 125V and 10A, 250V).

5. Bekas Gunung: Tolak bekas berwayar kembali ke dalam kotak elektrik dengan berhati-hati. Selamatkannya dengan skru pelekap yang disediakan.
6. Pasang Plat Dinding: Attach the decorative wall plate over the receptacle.
7. Pulihkan Kuasa: Turn the power back on at the circuit breaker or fuse box. Test the receptacle with a known working device.

Arahan Operasi

To operate the Hubbell 7051-G receptacle, simply insert the plug of your electrical device into one of the two available outlets. Ensure the plug is fully inserted. The receptacle is designed for standard 2-prong or 3-prong grounded plugs.

Imej: Depan view of the Hubbell 7051-G receptacle, ready for device plugs.

Penyelenggaraan

The Hubbell 7051-G receptacle requires minimal maintenance. Periodically inspect the receptacle and wall plate for any signs of damage, cracks, or discoloration. If any damage is observed, turn off power at the circuit breaker and replace the receptacle immediately. Clean the surface with a soft, dry cloth. Do not use abrasive cleaners or solvents.

Menyelesaikan masalah

• No Power at Receptacle:
  • Check the circuit breaker or fuse for the circuit. Reset the breaker or replace the fuse if tripped/blown.
  • Ensure all wire connections are secure. Turn off power before checking connections.
  • Uji bekas dengan voltage tester to confirm power presence.
• Loose Plug Connection:
  • If plugs do not stay firmly in the receptacle, the internal contacts may be worn. The receptacle should be replaced by a qualified electrician.
• Terlalu panas:
  • If the receptacle feels warm to the touch, immediately disconnect all devices and turn off power. This could indicate an overload or a faulty connection. Consult a qualified electrician.

Spesifikasi

Image: The Hubbell 7051-G receptacle shown in its original product box.

Image: Barcode label for the Hubbell 7051-G 2P 3W 15A 125V-AC Receptacle, showing product identification details including UPC 0129190665219.

Waranti dan Sokongan

Specific warranty information for the Hubbell 7051-G Receptacle is not provided within this manual. For warranty details or technical support, please contact Hubbell customer service directly or visit their official webtapak. Simpan resit pembelian anda sebagai bukti pembelian.

Pengeluar: HUBBELL

Webtapak: www.hubbell.com (Cthamppautan le, pautan sebenar mungkin berbeza-beza)