FERM TDM1026 Pillar Drill Instruction Manual

1. Pengenalan

This manual provides essential information for the safe and effective operation, setup, and maintenance of your FERM TDM1026 Pillar Drill. Please read these instructions carefully before using the machine to ensure proper function and to prevent injury or damage.

Image 1: The FERM TDM1026 Pillar Drill, showcasing its robust construction and key components.

2. Arahan Keselamatan

Sentiasa patuhi langkah berjaga-jaga keselamatan asas untuk mengurangkan risiko kebakaran, kejutan elektrik dan kecederaan diri. Simpan manual ini untuk rujukan masa hadapan.

• Keselamatan Kawasan Kerja: Pastikan kawasan kerja bersih dan terang. Kawasan bersepah atau gelap mengundang kemalangan. Jangan kendalikan alatan kuasa dalam atmosfera yang mudah meletup, seperti di hadapan cecair mudah terbakar, gas atau habuk.
• Keselamatan Elektrik: Palam alat kuasa mesti sepadan dengan alur keluar. Jangan sekali-kali mengubah suai palam dalam apa jua cara. Elakkan sentuhan badan dengan permukaan yang dibumikan atau dibumikan, seperti paip, radiator, julat dan peti sejuk.
• Keselamatan Diri: Always wear eye protection. Use hearing protection when operating the drill for extended periods. Do not overreach. Maintain proper footing and balance at all times.
• Penggunaan dan Penjagaan Alat: Jangan paksa alat kuasa. Gunakan alat kuasa yang betul untuk aplikasi anda. Putuskan sambungan palam daripada sumber kuasa sebelum membuat sebarang pelarasan, menukar aksesori atau menyimpan alatan kuasa.
• Hentian kecemasan: The machine is equipped with a red emergency stop button for immediate shutdown.
• Pengawal Keselamatan: A transparent safety guard is provided over the chuck area to protect against flying debris. Ensure it is always in place during operation.

3. Persediaan

3.1 Membongkar dan Memasang

Carefully remove all components from the packaging. Ensure all parts listed in the packing contents are present. Assemble the pillar drill according to the provided assembly diagram (not included in this document, refer to separate assembly sheet if applicable).

3.2 Mounting the Drill

The drill press features pre-drilled holes in its base for secure mounting to a workbench. This is highly recommended to ensure stability and safety during operation.

3.3 Adjusting the Work Table

The 160x160mm work table can be adjusted in height and tilted from -45° to 45°. Loosen the locking mechanism to adjust the table to the desired height and angle, then securely tighten it before drilling.

Image 2: Close-up of the adjustable work table and its angle indicator.

3.4 Installing the Drill Bit

The drill is equipped with a keyed chuck for securing various types of drill bits up to 13mm in diameter. Insert the drill bit into the chuck and tighten it firmly using the provided chuck key. Ensure the bit is centered and secure.

Image 3: The chuck key being used to tighten a drill bit in the chuck.

4. Arahan Operasi

4.1 Menghidupkan/Mematikan

The drill press features a main power switch. Press the green button to turn the machine on and the red button to turn it off. In case of emergency, press the large red emergency stop button.

Image 4: The main power switch with green 'on' and red 'off' buttons.

4.2 Melaraskan Tetapan Kelajuan

The FERM TDM1026 offers 5 different speed settings (500, 890, 1400, 1900, 2500 RPM). To change the speed, open the metal belt housing on top of the drill. Adjust the V-belt position on the pulleys to achieve the desired speed. Refer to the diagram inside the housing for correct belt placement. Ensure the machine is unplugged before adjusting the belt.

Image 5: The belt drive system for adjusting drilling speeds.

4.3 Menetapkan Kedalaman Penggerudian

Utilize the drilling depth stop to precisely control the depth of your drill hole, up to a maximum of 52mm. Adjust the depth stop mechanism to the required depth before starting the drilling operation.

Image 6: Close-up of the depth stop mechanism with measurement scale.

4.4 Operasi Menggerudi

Lekatkan bahan kerja dengan kuat pada meja kerja menggunakan clamps if necessary. Lower the drill bit slowly into the material using the feed handles. Apply steady, even pressure. The transparent safety guard provides visibility while protecting against debris.

Image 7: The pillar drill in use, demonstrating a drilling operation on a wooden workpiece.

Image 8: The transparent safety guard covering the drill chuck area.

5. Penyelenggaraan

Regular maintenance ensures the longevity and safe operation of your pillar drill. Always disconnect the power supply before performing any maintenance.

• Pembersihan: Keep the machine clean, especially the work table and column, to prevent accumulation of dust and debris. Use a dry cloth or soft brush.
• Pelinciran: Berkala pelincir bahagian bergerak seperti yang ditunjukkan dalam manual servis terperinci (jika berkenaan).
• Pemeriksaan Tali Pinggang: Regularly check the V-belt for wear and proper tension. Adjust or replace if necessary.
• Penyelenggaraan Chuck: Pastikan rahang chuck bersih dan bebas daripada serpihan untuk memastikan cengkaman mata gerudi yang betul.

6. Penyelesaian masalah

This section addresses common issues you might encounter with your pillar drill.

• Mesin tidak dimulakan:
  • Periksa sama ada kord kuasa dipasang dengan kukuh ke soket yang berfungsi.
  • Ensure the main power switch is in the 'on' position.
  • Verify that the belt housing cover is fully closed, as a safety interlock prevents operation when open.
  • Check if the emergency stop button is engaged; twist to release if pressed.
• Excessive vibration during operation:
  • Ensure the drill bit is properly installed and tightened in the chuck.
  • Check the V-belt tension and condition. A loose or worn belt can cause vibration.
  • Verify that the machine is securely mounted to the workbench.
• Drill bit not cutting effectively:
  • Ensure the drill bit is sharp and appropriate for the material being drilled.
  • Check that the correct speed setting is selected for the material and drill bit size.
  • Apply adequate, but not excessive, downward pressure.

7. Spesifikasi

8. Waranti dan Sokongan

For warranty information, technical support, or spare parts availability, please refer to the documentation provided with your purchase or contact FERM customer service directly. Specific details regarding warranty periods and service procedures are not included in this general instruction manual.