Hilti DX 351 Powder-Actuated Tool Instruction Manual

1. Pengenalan

This instruction manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of the Hilti DX 351 powder-actuated fastening tool. It is crucial to read and understand all instructions and safety warnings before using the tool. Keep this manual accessible for future reference.

2. Arahan Keselamatan

Always adhere to general safety regulations and local accident prevention rules. Failure to follow these instructions may result in serious injury or property damage.

• Alat Pelindung Diri (PPE): Always wear eye protection, hearing protection, and safety gloves when operating the tool.
• Kakitangan yang diberi kuasa: Only trained and authorized personnel should operate this tool.
• Kawasan Kerja: Pastikan kawasan kerja bebas daripada orang ramai dan bebas daripada bahan mudah terbakar.
• Keadaan alat: Inspect the tool for any damage before each use. Do not use a damaged tool.
• Fastener and Cartridge Compatibility: Use only Hilti-approved fasteners and cartridges that are compatible with the DX 351.
• Jangan sekali-kali menghalakan alat kepada diri sendiri atau orang lain.
• Storan: Store the tool, fasteners, and cartridges securely and out of reach of unauthorized persons.

3. Komponen Selesaiview

The Hilti DX 351 kit includes the following main components:

• DX 351 Basic Unit: The main body of the powder-actuated tool.
• X-P8S-351 Piston: An essential internal component for driving fasteners.
• Nail Magazine X-MX32 Assy: Attaches to the tool for sequential fastening of nails.
• DX 351 Cleaning Kit: Contains tools and brushes for routine maintenance.
• Case DX 351: For safe storage and transport of the tool and accessories.
• Concrete Nails X-P 22 MX (5000x): Fasteners designed for concrete applications.
• Cartridges 6.8/11 M.27 Cal Yellow (5000x): Powder loads used to power the tool.

4. Persediaan

Before operating the Hilti DX 351, ensure proper setup:

1. Attach Magazine: Securely attach the X-MX32 nail magazine to the tool body. Refer to the tool's markings for correct alignment and locking mechanism.
2. Load Cartridges: Insert the 6.8/11 M.27 cal yellow cartridges into the cartridge strip. Ensure the cartridges are fully seated and the strip is correctly loaded into the tool's cartridge chamber.
3. Load Fasteners: Insert the X-P 22 MX concrete nails into the magazine. Ensure they are properly aligned and feed smoothly.
4. Peraturan Kuasa: Adjust the power regulation dial (typically located at the rear of the tool) to the appropriate setting for the application and base material. Start with a lower setting and increase if necessary.
5. Semakan Fungsi: Perform a quick function check to ensure all components are securely attached and operating freely.

5. Arahan Operasi

Ikuti langkah-langkah ini untuk operasi yang selamat dan berkesan:

1. Pakai PPE: Always wear appropriate personal protective equipment, including eye and hearing protection.
2. Alat Kedudukan: Place the tool firmly and perpendicularly against the base material where the fastener is to be driven. Ensure the contact element is fully depressed.
3. Initiate Fastening: While maintaining firm pressure against the base material, pull the trigger to fire the cartridge and drive the fastener.
4. Tekanan Lepasan: After firing, release pressure from the tool and lift it from the work surface.
5. Check Fastening: Inspect the driven fastener to ensure it is properly seated. Adjust power settings if necessary for subsequent fastenings.
6. Clearing Misfires: In case of a misfire, keep the tool pressed against the work surface for at least 5 seconds. Then, carefully remove the cartridge strip and dispose of the misfired cartridge according to local regulations. Never attempt to re-fire a misfired cartridge.

6. Penyelenggaraan

Regular maintenance ensures the longevity and safe operation of your Hilti DX 351 tool.

• Pembersihan Harian: After each use, or at least daily, clean the tool using the provided DX 351 Cleaning Kit. Pay special attention to the piston, barrel, and magazine areas to remove powder residue and debris.
• Pemeriksaan: Regularly inspect the piston, buffer, and other wear parts for signs of damage or excessive wear. Replace worn components immediately with genuine Hilti parts.
• Pelinciran: Apply a thin layer of Hilti lubricant to moving parts as indicated in the detailed service instructions (not provided here, but implied).
• Storan: Store the clean and dry tool in its case, away from moisture and extreme temperatures. Remove all cartridges and fasteners before storage.
• Servis profesional: For complex repairs or comprehensive servicing, contact an authorized Hilti service center.

7. Penyelesaian masalah

This section addresses common issues you might encounter with the Hilti DX 351.

If problems persist after attempting these solutions, contact Hilti customer service or an authorized service center.

8. Spesifikasi

• model: Hilti DX 351
• Nombor Bahagian: 3553035
• Komponen yang Disertakan: DX351 Basic unit, X-P8S-351 Piston, Nail magazine X-MX32 assy, DX 351 Cleaning Kit, Case DX 351, 5000x Concrete nail X-P 22 MX, 5000x Cartridge 6.8/11 M.27 cal yellow
• Jenis Pengikat: X-P 22 MX Concrete Nails
• Jenis Kartrij: 6.8/11 M.27 Cal Yellow
• Pengeluar: Hilti
• gaya: moden
• Bateri Diperlukan: Tidak

9. Waranti dan Sokongan

Hilti products are designed for durability and reliability. For information regarding product warranty, service, or technical support, please refer to the official Hilti website or contact your local Hilti representative. Keep your purchase receipt for warranty claims.

Untuk bantuan lanjut, sila layari laman web rasmi Hilti webtapak: www.hilti.com