VEMER VE618500 CM100 Wall Thermostat User Manual

1. Pengenalan

The VEMER VE618500 CM100 is a battery-powered, daily programmable wall thermostat designed for controlling heating systems. Its intuitive mechanical interface allows for easy setting of daily heating schedules and desired temperatures. This manual provides detailed instructions for the proper installation, setup, operation, and maintenance of your thermostat.

2. Maklumat Keselamatan

• Keselamatan Elektrik: Installation should be performed by a qualified electrician or competent person in accordance with local wiring regulations. Always disconnect power to the heating system at the main circuit breaker before beginning any wiring work.
• Keselamatan Bateri: Use only the specified battery type (2 x 1.5V AA). Do not mix old and new batteries, or different types of batteries. Dispose of used batteries responsibly.
• penempatan: Install the thermostat away from direct sunlight, drafts, and heat sources (e.g., radiators, lamps) to ensure accurate temperature readings.
• Pembersihan: Do not use abrasive cleaners or solvents. Clean the thermostat with a soft, damp kain sahaja.

3. Kandungan Pakej

Sila pastikan semua item ada dalam pakej:

• VEMER VE618500 CM100 Wall Thermostat Unit
• Installation Kit (screws, wall plugs)
• Manual Pengguna

4. Produk Lebihview

Familiarize yourself with the main components and controls of your thermostat.

Rajah 1: Depan View of the Thermostat. This image displays the front of the VEMER VE618500 CM100 thermostat, showing the large central time dial with 15-minute riders, the temperature setting dial on the right, and the mode selector switch.

4.1 Kawalan Panel Hadapan

• Time Dial (Left): A 24-hour dial with 96 movable riders (pins). Each rider represents a 15-minute interval. Push riders outwards for 'ON' periods and inwards for 'OFF' periods. The current time is indicated by a pointer.
• Temperature Dial (Right): Used to set the desired room temperature, typically ranging from 5°C to 35°C.
• Suis Pemilih Mod: Located near the temperature dial, this switch allows you to select the operating mode.
• Butang TETAP SEMULA: A small button, usually recessed, to reset the thermostat.

Rajah 2: Sisi View with Mode Selector. This image shows a close-up of the side of the thermostat, highlighting the mode selector switch, which typically has positions for 'OFF', 'Programmed', and 'Continuous ON'.

4.2 Rear Panel (for Installation)

Rajah 3: Belakang View of the Thermostat. This image displays the back of the VEMER VE618500 CM100 thermostat, showing the mounting holes, wiring terminals (L, NO, NC), and the battery compartment cover. The model number and electrical ratings are also visible.

• Terminal Pendawaian: Connections for the heating system (typically Live, Normally Open, Normally Closed).
• Petak Bateri: Holds 2 x 1.5V AA batteries.
• Lubang Pemasangan: For securing the thermostat to the wall.

5. Pemasangan

Penting: Ensure power to the heating system is disconnected before proceeding.

5.1 Lokasi Pemasangan

Choose an interior wall location, approximately 1.5 meters (5 feet) from the floor, away from:

• Cahaya matahari langsung
• Drafts from windows or doors
• Heat sources (e.g., radiators, televisions, lamps)
• Areas with poor air circulation

5.2 Memasang Termostat

1. Carefully separate the front cover from the backplate of the thermostat.
2. Position the backplate on the chosen wall location and mark the drilling points.
3. Gerudi lubang dan masukkan palam dinding (jika perlu).
4. Lekatkan plat belakang ke dinding menggunakan skru yang disediakan.

5.3 Pendawaian

Refer to the wiring diagram on the back of the thermostat (see Rajah 3) and your heating system's manual for specific connections. Typically, the thermostat acts as a simple switch for your boiler. Connect the heating system's control wires to the appropriate terminals (L, NO, NC) on the thermostat's backplate.

Pastikan semua sambungan kukuh dan berpenebat dengan betul.

5.4 Memasukkan Bateri

1. Open the battery compartment cover on the rear of the thermostat.
2. Insert two 1.5V AA alkaline batteries, observing the correct polarity (+/-).
3. Tutup penutup petak bateri.

Once wiring and batteries are installed, reattach the front cover to the backplate. Restore power to the heating system.

6. Persediaan Awal

6.1 Menetapkan Masa Semasa

1. Gently rotate the central time dial clockwise until the current time aligns with the fixed pointer on the thermostat. The dial is a 24-hour clock.

6.2 Setting the Desired Temperature

1. Rotate the temperature dial on the right to your desired room temperature. This is the temperature the thermostat will maintain during 'ON' periods.

7. Operasi

7.1 Daily Programming

The VEMER VE618500 CM100 uses 96 movable riders around the time dial for daily programming. Each rider represents a 15-minute interval.

1. To set an 'ON' period (heating active): Push the corresponding riders outwards.
2. To set an 'OFF' period (heating inactive): Push the corresponding riders inwards.

The thermostat will activate the heating system when the current time falls within an 'ON' period (riders pushed outwards) and the room temperature is below the set temperature.

7.2 Pemilihan Mod

Use the mode selector switch (see Rajah 2) to choose the operating mode:

• Programmed Mode (Clock/Timer Symbol): The thermostat operates according to the daily program set by the riders on the time dial.
• Continuous ON Mode (Sun Symbol): The heating system will remain active continuously, attempting to maintain the set temperature, regardless of the program.
• OFF Mode (Moon Symbol / Snowflake Symbol): The heating system will remain off, regardless of the program or temperature. This is useful for extended absences or during warmer seasons.

8. Penyelenggaraan

8.1 Penggantian Bateri

When the batteries are low, the thermostat's performance may be affected. Replace the batteries as follows:

1. Tanggalkan penutup hadapan termostat dengan berhati-hati.
2. Buka petak bateri.
3. Keluarkan bateri lama dan buang dengan betul.
4. Insert two new 1.5V AA alkaline batteries, ensuring correct polarity.
5. Close the battery compartment and reattach the front cover.

After battery replacement, you may need to reset the current time.

8.2 Pembersihan

Clean the thermostat's exterior with a soft, dry, or slightly damp cloth. Do not use chemical cleaners, abrasives, or solvents, as these can damage the casing.

9. Penyelesaian masalah

10. Spesifikasi

Figure 4: Thermostat Dimensions. This image provides a visual representation of the VEMER VE618500 CM100 thermostat's dimensions, indicating a width of approximately 15.6 cm (6.1 inches) and a height of 9 cm (3.5 inches).

11. Waranti dan Sokongan

This VEMER product is covered by a manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or contact VEMER customer support. For technical assistance or inquiries, please visit the official VEMER webtapak atau hubungi pusat perkhidmatan mereka yang dibenarkan.