Manual Arahan Mandian Air Memmert WNE 7-230V 7L

1. Pengenalan

This manual provides essential information for the safe and efficient operation of your Memmert WNE 7-230V 7L Water Bath. Please read these instructions thoroughly before initial setup and operation to ensure proper use and to prevent damage to the unit or injury to personnel. The Memmert WNE series water baths are designed for precise temperature control in laboratory applications, offering excellent overtemperature protection and user-friendly features.

2. Arahan Keselamatan

Adherence to safety guidelines is crucial for preventing accidents and ensuring the longevity of the equipment.

• Keselamatan Elektrik: Ensure the unit is connected to a properly grounded power outlet with the correct voltage (230V). Do not operate with damaged power cords. Disconnect power before cleaning or servicing.
• Permukaan Panas: The water bath and its contents will become hot during operation. Use appropriate personal protective equipment (PPE) such as heat-resistant gloves when handling the unit or samples. Allow the unit to cool before moving or cleaning.
• Stim dan Air Panas: Be aware of steam escaping from the bath, especially when opening the lid. Avoid direct contact with hot water.
• Tumpahan cecair: Prevent water or other liquids from spilling onto electrical components. In case of a spill, immediately disconnect power and clean thoroughly.
• Pengudaraan: Ensure adequate ventilation around the unit to prevent heat buildup.
• Penggunaan yang Dimaksudkan: Use the water bath only for its intended purpose as a laboratory heating device. Do not use with flammable or corrosive liquids unless specifically designed for such applications.

3. Persediaan

Follow these steps for initial setup of your Memmert WNE 7-230V Water Bath.

1. Membongkar: Carefully remove the water bath from its packaging. Inspect for any signs of shipping damage. Retain packaging for future transport or storage.
2. penempatan: Place the unit on a stable, level, heat-resistant surface in a well-ventilated area. Ensure there is sufficient clearance around the unit for air circulation.
3. Sambungan Kuasa: Connect the power cord to the rear of the unit and then to a grounded 230V AC power outlet.
4. Mengisi Mandian: Fill the bath with distilled or deionized water up to the recommended fill line. Do not overfill. Ensure the heating elements are fully submerged.

Figure 3.1: Memmert WNE 7-230V Water Bath ready for operation. The image displays the stainless steel exterior, the open lid revealing the internal heating elements, and the digital control panel on the front.

4. Arahan Operasi

Operating your Memmert WNE 7-230V Water Bath is straightforward with its intuitive controls.

1. Hidupkan kuasa: Turn on the main power switch, usually located on the front or rear panel. The digital display will illuminate.
2. Menetapkan Suhu: Use the control knob and display interface to set the desired temperature. Refer to the specific instructions for your controller version for detailed navigation. The unit features a +/- 5K recalibration facility for precise temperature control.
3. Proses Pemanasan: The bath will begin heating to the setpoint. The display will show the current temperature. The unit is designed for excellent user friendliness, allowing programmable start of hold time only after reaching the temperature setpoint.
4. Perlindungan Terlebih Suhu: The Memmert WNE series includes excellent overtemperature protection and a digital level monitor. In case of an overtemperature condition or low water level, visual and audible alarm signals will activate to ensure secure long-term tests.
5. Pemantauan: Periodically monitor the water level and temperature during operation. Refill with distilled water if the level drops significantly due to evaporation.
6. Matikan: When testing is complete, turn off the main power switch. Allow the unit to cool down before emptying or cleaning.

5. Penyelenggaraan

Regular maintenance ensures optimal performance and extends the lifespan of your water bath.

• Pembersihan: Regularly clean the interior of the bath to prevent algae growth and mineral buildup. Use a mild detergent and a soft cloth. Rinse thoroughly with distilled water. Do not use abrasive cleaners or sharp objects.
• Penggantian Air: Replace the water in the bath regularly, especially if it appears cloudy or discolored. Always use distilled or deionized water to prevent mineral deposits on the heating elements and bath walls.
• Pembersihan Luaran: Lap permukaan luar dengan damp cloth. Avoid getting water into the control panel or ventilation openings.
• Penentukuran: The unit features a +/- 5K recalibration facility on the controller for quality assurance. Consult a qualified technician for periodic calibration checks to maintain accuracy.
• Storan: Jika menyimpan unit untuk tempoh yang lama, pastikan ia bersih, kering dan disimpan di tempat yang sejuk dan kering.

6. Penyelesaian masalah

Bahagian ini menangani isu biasa yang mungkin anda hadapi.

For issues not listed here or if troubleshooting steps do not resolve the problem, please contact Memmert technical support.

7. Spesifikasi

Key technical specifications for the Memmert WNE 7-230V Water Bath.

• model: WNE 7-230V
• kapasiti: 7 Liters (7L)
• Voltage: 230V
• Kawalan Suhu: Excellent temperature controller with +/- 5K recalibration facility
• Ciri-ciri Keselamatan: Excellent overtemperature protection, Digital level monitor with visual and audible alarm signals
• Pengeluar: Memmert
• Negara Asal: Jerman

8. Waranti dan Sokongan

For information regarding product warranty, technical support, or service, please refer to the warranty card included with your product or visit the official Memmert website. It is recommended to register your product to ensure access to full support services.