Hyundai HY6000 Gasoline Generator User Manual

3.1 Membongkar dan Pemeriksaan

Carefully remove the generator from its packaging. Inspect for any damage that may have occurred during shipping. If any damage is found, contact your dealer immediately.

3.2 Penempatan

Place the generator on a firm, level surface. Ensure there is adequate clearance around the unit for proper ventilation and to prevent heat buildup. Keep it at least 1 meter (3 feet) away from buildings or other equipment.

3.3 Menambah Minyak Enjin

The generator is shipped without engine oil. Before first use, add the recommended engine oil (e.g., SAE 10W-30) to the crankcase. Refer to the oil fill cap or dipstick for the correct level. Do not overfill.

Rajah 1: sebelah view of the generator engine. The oil fill cap is typically located on the side of the engine block, often yellow or black, and may have a dipstick attached for checking oil level.

3.4 Menambah Bahan Api

Use fresh, unleaded gasoline with an octane rating of 87 or higher. Fill the fuel tank carefully, avoiding spills. Do not fill above the red indicator or the bottom of the filler neck. Securely close the fuel cap after filling.

• Always refuel in a well-ventilated outdoor area.
• Ensure the engine is off and cool before refueling.
• Do not smoke or use open flames near the generator.

3.5 Membumikan Penjana

For safety, the generator must be properly grounded. Connect a heavy-gauge copper wire from the generator's grounding terminal to an earth ground rod or other approved grounding source. Consult local electrical codes for specific requirements.

4.1 Panel Kawalan Selesaiview

Rajah 2: Depan view of the control panel. Features include two 16A AC outlets, a digital LED display for voltage/frequency/hours, a circuit breaker, and a DC 12V output with thermal protection.

Panel kawalan termasuk:

• AC Outlets (2x 16A): For connecting 220V appliances. Equipped with overload protection.
• Paparan LED Digital: Pertunjukan voltage, kekerapan dan waktu operasi.
• Pemutus litar: Melindungi daripada lebihan beban.
• DC 12V Output (8.3A): For charging 12V batteries, with thermal protection.
• Terminal Pembumian: For connecting to an earth ground.
• Penunjuk LED: For overload or usage status.

4.2 Starting the Engine (Manual Start)

1. Pastikan penjana berada di atas permukaan yang rata dan dibumikan dengan betul.
2. Periksa tahap minyak enjin dan bahan api.
3. Putar injap bahan api ke kedudukan "ON".
4. Move the choke lever to the "CHOKE" position (if the engine is cold).
5. Putar suis enjin ke kedudukan "ON".
6. Grasp the recoil starter handle firmly and pull it slowly until resistance is felt, then pull quickly and smoothly to start the engine.
7. Sebaik sahaja enjin dihidupkan, perlahan-lahan gerakkan tuil cok ke kedudukan "RUN".
8. Biarkan enjin panas selama beberapa minit sebelum menyambungkan beban elektrik.

Rajah 3: sebelah view of the generator, highlighting the manual recoil pull start handle, typically yellow or black, located on the engine's flywheel cover.

4.3 Menyambungkan Beban Elektrik

After the engine has warmed up, you can connect your appliances. Ensure the total wattage of connected devices does not exceed the generator's rated output (4400W). Overloading the generator will trip the circuit breaker.

• Plug appliances directly into the AC outlets on the control panel.
• For 12V DC charging, connect the appropriate cables to the DC output.
• If the generator stops due to overload, reduce the load and reset the circuit breaker.

4.4 Menghentikan Enjin

1. Putuskan sambungan semua beban elektrik daripada penjana.
2. Putar suis enjin ke kedudukan "OFF".
3. Putar injap bahan api ke kedudukan "OFF".

5.1 Jadual Penyelenggaraan

5.2 Penukaran Minyak Enjin

Drain the old oil while the engine is warm. Remove the oil drain plug and allow all oil to drain into a suitable container. Replace the drain plug and refill with the recommended amount and type of new engine oil.

5.3 Pembersihan Penapis Udara

Remove the air filter cover and take out the foam filter element. Wash it in warm, soapy water, rinse thoroughly, and allow it to dry completely. Lightly oil the foam element with engine oil, squeeze out excess, and reinstall.

5.4 Pemeriksaan Palam Pencucuh

Remove the spark plug and inspect its condition. Clean any carbon deposits with a wire brush. Check the gap with a feeler gauge and adjust if necessary. Replace if the electrode is worn or damaged.

5.5 Penyimpanan

For long-term storage, drain the fuel tank and carburetor, or add a fuel stabilizer. Change the engine oil. Clean the generator thoroughly. Store in a clean, dry, well-ventilated area.