Manual Pengguna Lampu Strob Amaran Maxxima M20384WYCL Putih/Amber Ultra Nipis 4 LED

1. Produk Lebihview

The Maxxima M20384WYCL is an ultra-thin profile 4 LED warning light designed for surface mounting. This model features 2 white LEDs and 2 amber LEDs with a clear lens, providing strong light output for emergency, warning, and safety applications. Its low-profile design allows for easier mounting and a slimmer appearance.

Imej 1.1: Depan view of the Maxxima M20384WYCL White/Amber Ultra Thin 4 LED Warning Strobe Light.

2. Apa yang ada di dalam Kotak

Sahkan bahawa semua komponen hadir sebelum memulakan pemasangan.

• Maxxima M20384WYCL Warning Strobe Light
• Gasket
• Snap-On Black Bezel
• Skru Pemasangan

3. Persediaan dan Pemasangan

This warning light is designed for surface mount installation. Ensure the mounting surface is clean, flat, and provides adequate space for the light and wiring.

3.1 Pemasangan

1. Select a suitable mounting location on your vehicle. The light's dimensions are approximately 4.4 inches (L) x 0.9 inches (D) x 1.5 inches (H).
2. Position the light with the included gasket and black bezel. Mark the drilling points for the mounting screws.
3. Gerudi lubang perintis di lokasi yang ditanda.
4. Secure the light to the surface using the provided mounting screws. Ensure a tight fit to prevent moisture ingress.

Optional mounting accessories are available and sold separately, including Maxxima Part# M50144 for grommet mounting, M50138 for a chrome bezel, or M50115 for a stainless steel bracket.

Imej 3.1: Pro sampinganfile of the warning light, highlighting its ultra-thin design.

Imej 3.2: Cthample installation of the warning light on a vehicle grille.

3.2 Pendawaian

The M20384WYCL light features 4 blunt cut leads for electrical connection. Ensure all connections are secure and properly insulated to prevent short circuits and corrosion.

Imej 3.3: Belakang view of the light with wiring leads.

Typical Wiring Configuration:

• Kawat Merah: Positive (+) power input (12.8 VDC). Connect to a fused power source.
• Kawat Hitam: Negative (-) ground. Connect to a chassis ground.
• Kawat kuning: Pattern selection. Momentarily touch this wire to the black (ground) wire to cycle through the 22 available flash patterns.
• Kawat Putih: Synchronization. Connect the white wires of multiple lights together for synchronized or alternating flashing. Refer to the specific wiring diagram for your desired synchronization mode (not provided in general product data).

Always disconnect power before making any electrical connections.

4. Arahan Operasi

The Maxxima M20384WYCL warning light offers 22 selectable flash patterns and is capable of both synchronized and alternating flashing.

4.1 Menghidupkan/Mematikan

Once properly wired, the light will activate when power is supplied to the red wire. To turn the light off, remove power from the red wire.

4.2 Changing Flash Patterns

With the light powered on, momentarily touch the yellow wire to the black (ground) wire. Each momentary touch will advance the light to the next flash pattern in its sequence. Cycle through the patterns until the desired one is selected.

4.3 Penyegerakan

For synchronized or alternating flashing with multiple M20384WYCL lights, connect the white wires of all lights together. The specific synchronization behavior (e.g., all flash together, or alternate) is typically determined by the selected flash pattern and the wiring configuration (refer to a detailed wiring diagram if available from the manufacturer for specific synchronization modes).

Image 4.1: Key features of the warning light.

5. Penyelenggaraan

The Maxxima M20384WYCL warning light is designed for durability and minimal maintenance.

• Pembersihan: Clean the lens periodically with a soft cloth and mild soap and water. Avoid abrasive cleaners or solvents that could damage the polycarbonate lens.
• Pemeriksaan: Regularly inspect the wiring for any signs of wear, damage, or corrosion. Ensure mounting screws remain tight.
• Ketahanan: The unit features a polycarbonate lens and housing, and completely resin-sealed electronics, providing protection against environmental elements.

6. Penyelesaian masalah

If you encounter issues with your Maxxima M20384WYCL warning light, consider the following:

• Light does not illuminate:
  • Check all electrical connections (red wire to positive, black wire to ground).
  • Verify that the power source is active and providing 12.8 VDC.
  • Check for any blown fuses in the power circuit.
• Light flashes erratically or not as expected:
  • Ensure the yellow pattern selection wire is not continuously grounded, which could interfere with pattern selection.
  • If multiple lights are synchronized, check the white wire connections for continuity and proper isolation from ground.
• Moisture inside the lens: While the unit is resin-sealed, extreme conditions or improper installation can sometimes lead to condensation. If persistent, contact Maxxima support.

If troubleshooting steps do not resolve the issue, refer to the warranty information for further assistance.

7. Spesifikasi

Imej 7.1: Perwakilan visual spesifikasi produk.

8. Maklumat Waranti

The Maxxima M20384WYCL Warning Strobe Light is backed by a 5 Year Maxxima Warranty. This warranty covers defects in materials and workmanship under normal use. For warranty claims or detailed terms and conditions, please contact Maxxima customer support.

9. Sokongan

For technical assistance, product inquiries, or warranty support, please visit the official Maxxima webtapak atau hubungi bahagian perkhidmatan pelanggan mereka. Anda juga boleh melawat Kedai Maxxima di Amazon untuk maklumat dan sumber produk tambahan.