pengenalan
This manual provides comprehensive instructions for the installation, operation, programming, and maintenance of your Braeburn 5-2 Day Programmable Thermostat. Please read this manual thoroughly before attempting to install or operate your new thermostat.
Rajah 1: Depan view of the Braeburn 5-2 Day Programmable Thermostat, showing the large blue backlit display, system mode switch, fan mode switch, and programming buttons.
Ciri-ciri
- 5-2 Day Programmability
- Besar 2 Sq. Dalam. Paparan dengan Lampu Latar Biru Terang
- Had Suhu Boleh Laras
- Hardwire or Battery Powered (24V AC)
- Memori Kekal Mengekalkan Tetapan
- Monitor Semak Penapis
- Perbezaan Suhu Boleh Laras
- Adaptive Recovery Mode (ARM)
- Litar Elektronik Pengawal ESD
- Perlindungan Kitaran Pendek Pemampat
- Pembatalan Program Sementara
- Mod Tahan Lanjutan Boleh Aturcara
- Butang Tetapan Semula Akses Depan
- Suis F° / C°
Pemasangan dan Persediaan
Langkah-langkah Keselamatan
- AMARAN: Disconnect power to the heating and cooling system before installing or servicing the thermostat.
- Pemasangan hendaklah dilakukan oleh juruteknik bertauliah.
- Ensure wiring complies with local electrical codes.
Lokasi Pemasangan
Install the thermostat on an inside wall, approximately 5 feet (1.5m) above the floor. Avoid locations near heat sources (lamps, sunlight, fireplaces), drafts (windows, doors), or unconditioned spaces (unheated hallways, outside walls).
Arahan Pendawaian
This thermostat is designed for single-stage (1 Heat/1 Cool) systems. It can be powered by 24V AC hardwire or batteries.
Typical Terminations: Rc, Rh, O, B, Y1, W1, G, C
- Matikan kuasa pada sistem HVAC di pemutus litar.
- Remove the old thermostat from the wall plate.
- Label each wire with the terminal designation from your old thermostat.
- Mount the new thermostat base plate to the wall.
- Connect the labeled wires to the corresponding terminals on the new thermostat. Refer to the wiring diagram provided with your thermostat for specific connections.
- Insert 2 AA alkaline batteries (not included) into the battery compartment if using battery power or as a backup.
- Attach the thermostat body to the base plate.
- Kembalikan kuasa ke sistem HVAC.
Mengendalikan Termostat Anda
Suis Mod Sistem
Located on the front of the thermostat, this switch controls the overall operation mode:
- KEREN: The thermostat will operate your cooling system.
- MATI: Sistem pemanasan dan penyejukan dimatikan.
- HABA: The thermostat will operate your heating system.
Fan Mode Switch
Located on the front of the thermostat, this switch controls the fan operation:
- AUTO: Kipas hanya berfungsi apabila sistem pemanasan atau penyejukan aktif.
- ON: Kipas berjalan secara berterusan, tanpa mengira panggilan pemanasan atau penyejukan.
Menetapkan Suhu
Gunakan UP dan TURUN arrow buttons on the right side of the display to adjust the desired temperature (setpoint). The display will show both the current room temperature and the setpoint.
Programming (5-2 Day)
The 5-2 day programming allows you to set different schedules for weekdays (Monday-Friday) and weekends (Saturday-Sunday). Each day can have up to 4 program periods: Morning, Day, Evening, and Night.
Menetapkan Masa dan Hari
- Tekan ke PROG button once. The display will show the current time flashing.
- Gunakan UP or TURUN anak panah untuk melaraskan masa.
- Tekan PROG again to advance to the day setting. The day will flash.
- Gunakan UP or TURUN arrows to adjust the day.
- Tekan PROG or wait 15 seconds to exit.
Setting Program Schedule
- Tekan ke PROG button until "MON-FRI" appears and the time for the first period (Morning) flashes.
- Gunakan UP or TURUN arrows to set the desired time for the Morning period.
- Tekan PROG. The temperature for the Morning period will flash.
- Gunakan UP or TURUN anak panah untuk menetapkan suhu yang dikehendaki.
- Repeat steps 2-4 for the Day, Evening, and Night periods for "MON-FRI".
- After setting the "MON-FRI" schedule, press PROG to advance to "SAT-SUN" and repeat the process for weekend programming.
- Tekan KEMBALI or wait 15 seconds to exit programming mode.
Pembatalan Program Sementara
To temporarily change the temperature without affecting the program, simply use the UP or TURUN arrows. The thermostat will hold this temperature until the next program period begins.
Pegangan Kekal
Tekan ke TAHAN button. The thermostat will maintain the current temperature indefinitely. To cancel, press TAHAN sekali lagi atau tekan PROG to resume the schedule.
Penyelenggaraan
Penggantian Bateri
When the battery indicator appears on the display, replace the 2 AA alkaline batteries immediately to ensure proper operation and prevent loss of settings. The thermostat has permanent memory, so settings will be retained during battery replacement.
- Tarik badan termostat perlahan-lahan keluar dari plat dinding.
- Keluarkan bateri lama.
- Insert new AA alkaline batteries, observing polarity (+/-).
- Pasangkan semula badan termostat pada plat dinding.
Pembersihan
Bersihkan termostat dengan lembut, damp kain. Jangan gunakan pembersih atau pelarut yang melelas.
Monitor Semak Penapis
The thermostat may feature a filter check monitor that reminds you to change your air filter. Consult your HVAC system manual for recommended filter replacement intervals.
Menyelesaikan masalah
| Masalah | Kemungkinan Punca | Penyelesaian |
|---|---|---|
| Tiada paparan atau skrin kosong | No power, dead batteries, loose wiring. | Check circuit breaker, replace batteries, check wiring connections. |
| System not responding (no heat/cool) | System switch in OFF position, wrong mode selected, blown fuse in HVAC system, wiring issue. | Set system switch to HEAT or COOL, verify mode, check HVAC fuse, inspect wiring. |
| Temperature inaccurate | Thermostat located near heat source/draft, sensor issue. | Relocate thermostat if possible, ensure proper airflow around unit. |
| Kipas berjalan secara berterusan dalam mod AUTO | Suis kipas ditetapkan kepada HIDUP. | Set fan switch to AUTO. |
| Pengaturcaraan tidak berfungsi | Temporary override active, HOLD mode active, programming error. | Cancel temporary override, press HOLD to deactivate, re-enter program schedule carefully. |
If problems persist, contact a qualified HVAC technician or Braeburn customer support.
Spesifikasi
| Nombor Model | 2020NC, BRA1220NC |
| Permohonan | Bujang Stage (1 Heat / 1 Cool) |
| Kebolehprograman | 5-2 Day Programmable |
| Kaedah Kuasa | 24V AC Hardwire or Battery Powered (2 AA Alkaline) |
| Voltage | 24 Volt |
| Jenis Paparan | LED with Blue Backlight |
| Antara Muka Pengguna | Butang Tekan |
| Jenis Pemasangan | Wall Mount (Horizontal) |
| Dimensi (H x D) | 3.62" x 1.38" (anggaran) |
| UPC | 384929207680 |
Waranti dan Sokongan
For warranty information and technical support, please refer to the documentation included with your product or visit the official Braeburn webtapak. Simpan resit pembelian anda sebagai bukti pembelian.
Pengeluar: Braeburn
