pengenalan
This manual provides essential instructions for the installation, operation, and maintenance of your Texas Instruments 3.7L1200SP rechargeable battery. This battery is designed for compatibility with specific Texas Instruments calculators, including the TI Nspire, TI Nspire CAS, TI Nspire CX, TI Nspire CX CAS (V1.0 with wire), and TI 84 Plus C SE (with wire).
Please read this manual thoroughly before installing and using the battery to ensure proper function and longevity.
Persediaan dan Pemasangan
Follow these steps to replace or install the rechargeable battery in your compatible Texas Instruments calculator.
- Matikan: Ensure your calculator is completely powered off before beginning the installation process.
- Cari Petak Bateri: Identify the battery compartment on the back of your calculator.
- Keluarkan Skru: Use a small Phillips head screwdriver to remove the two screws securing the battery compartment cover. Carefully set the screws aside to avoid losing them.
- Buka Penutup: Tanggalkan penutup petak bateri perlahan-lahan.
- Disconnect Old Battery (if applicable): If replacing an old battery, carefully unplug its connector from the calculator's circuit board. Do not pull on the wires; grasp the connector itself.
- Masukkan Bateri Baharu: Position the new 3.7L1200SP battery into the compartment. Ensure it fits snugly.
- Sambungkan Bateri Baharu: Carefully plug the new battery's connector into the corresponding port on the calculator's circuit board. Ensure the connection is secure.
- Replace Cover and Screws: Place the battery compartment cover back into position and secure it with the two Phillips head screws. Do not overtighten.
Image: The Texas Instruments 3.7L1200SP rechargeable battery. This image shows the battery unit, which is installed into the calculator's battery compartment.
After installation, it is recommended to fully charge the battery before initial use.
Mengendalikan dan Mengecas
The 3.7L1200SP battery is designed for rechargeable use. Follow these guidelines for optimal performance.
Caj Permulaan
Upon first installation or after extended storage, fully charge the battery. A complete charge may take approximately one day (24 hours) to reach 100% capacity, especially if the battery is completely depleted.
Pengecasan Biasa
Connect your calculator to a power source using the appropriate charging cable (typically a USB cable provided with your calculator). The calculator's display will usually indicate the charging status. It is advisable to charge the battery when the charge level is low to maintain battery health.
Petunjuk Hayat Bateri
Your calculator's operating system will provide an indication of the battery charge level. This typically shows increments such as 0%, 25%, 50%, 75%, and 100%.
Penyelenggaraan dan Penjagaan
Proper care can extend the life of your rechargeable battery.
- Elakkan Pelepasan Dalam: Do not allow the battery to completely discharge for prolonged periods. Recharge it when the charge level is low.
- Storan: If storing the calculator for an extended period, ensure the battery has a partial charge (around 50%) and store it in a cool, dry place. Avoid extreme temperatures.
- Pembersihan: Keep the battery compartment clean and free of dust or debris.
- Suhu: Operate and charge the battery within recommended temperature ranges (typically room temperature) to prevent damage.
Menyelesaikan masalah
Jika anda menghadapi masalah dengan bateri anda, pertimbangkan penyelesaian biasa berikut:
- Bateri Tidak Dicas:
- Ensure the charging cable is securely connected to both the calculator and the power source.
- Sahkan sumber kuasa aktif.
- Cuba kabel pengecasan atau penyesuai kuasa yang berbeza.
- Confirm the battery connector inside the calculator is properly seated.
- Hayat Bateri Pendek:
- Ensure the battery has been fully charged. Initial charges can take longer.
- Check for excessive background processes or high screen brightness on your calculator, which can drain the battery faster.
- If the battery is several years old, its capacity may naturally degrade over time.
- Calculator Not Powering On:
- Pastikan bateri dipasang dengan betul dan dicas sepenuhnya.
- Connect the calculator to a power source and attempt to power it on while connected.
- If the issue persists, it may not be battery-related. Consult your calculator's specific user manual or Texas Instruments support.
Spesifikasi
| Nombor Model | 3.7L1200SP |
| Voltage | 3.7V |
| Kapasiti | 1200mAh |
| Nombor Bahagian | P11P35-09-N01 (1ICP5/43/50) |
| Jenis Bateri | Litium Ion |
| Keserasian | TI Nspire, TI Nspire CAS, TI Nspire CX, TI Nspire CX CAS (V1.0 with wire), TI 84 Plus C SE (with wire) |
| Berat Barang | 1.13 auns |
| Dimensi Pakej | 2.68 x 2.68 x 0.59 inci |
Waranti dan Sokongan
For warranty information or technical support regarding your Texas Instruments battery or calculator, please refer to the official Texas Instruments webtapak atau hubungi perkhidmatan pelanggan mereka secara langsung. Simpan resit pembelian anda sebagai bukti pembelian.
Texas Instruments Official Webtapak: education.ti.com
