Manual Pengguna Pam Permintaan Remco 5.3 GPM

1. Pengenalan

The Remco 5500 series 5.3 GPM Demand Pump (Model: 5517-1E1-82B) is a professional-grade solution designed for performance and efficiency in various applications, particularly agricultural spray applications. This pump features a 60 PSI pressure setting and a sealed 12-volt electric motor, engineered to operate reliably even in harsh environments.

Constructed with durable components, the 5500 Series pump is built to withstand long and continuous duty cycles. Its materials are compatible with common agricultural chemicals, including herbicides, fertilizers, and insecticides. This manual provides essential information for the safe and effective setup, operation, and maintenance of your Remco pump.

Ciri-ciri Utama:

• Professional Grade Quality
• 5.3 GPM (20.06 LPM) flow rate, 60 PSI (4.1 Bar) on Demand
• Made In the U.S.A.
• 6" length 14 AWG wire leads with SAE 2 pin connector
• Highest flow rate and lowest operating temperature at spray pressures
• Chemically compatible with common Agricultural chemicals
• 100% Factory Tested
• Completely Sealed Motor
• Low Heat and Power Consumption
• Superior Vertical Priming

Figure 1: Remco 5.3 GPM Demand Pump (Model 5517-1E1-82B)

2. Maklumat Keselamatan

Always read and understand all instructions before operating the pump. Failure to follow safety guidelines can result in injury or damage to the equipment.

• Ensure the power source is disconnected before performing any maintenance or installation.
• Wear appropriate personal protective equipment (PPE) when handling chemicals or operating the pump.
• Do not exceed the maximum liquid temperature of 140°F (60°C).
• For optimal performance and motor life, ensure the motor surface temperature does not exceed 150°F (66°C). The motor is not equipped with thermal protection.
• Verify chemical compatibility before use to prevent damage to the pump components.
• Keep the pump away from flammable materials and open flames.
• Pastikan pengudaraan yang betul semasa operasi.

3. Persediaan dan Pemasangan

Proper installation is crucial for the optimal performance and longevity of your Remco pump. Follow these steps carefully:

3.1 Memasang Pam

• Mount the pump in a secure, dry location, protected from direct weather exposure.
• Ensure adequate space around the pump for ventilation and access for maintenance.
• The pump can self-prime up to 14 feet (4.0 m) vertically. Position it as close as possible to the fluid source for best results.

3.2 Sambungan Elektrik

• The pump operates on 12 VDC. Connect the 14 AWG wire leads (6" or 12" 2-Pin Mold / Custom Connection) to a suitable 12-volt power source.
• Ensure correct polarity: Red wire is positive (+), Black wire is negative (-).
• Use appropriate fusing for the electrical circuit to protect the pump and power supply.

Figure 2: SAE 2-pin connector on the pump's wire leads

3.3 Fluid Connections

• The pump features 3/4" Quick Attach Ports for fluid connections.
• Connect the inlet port to your fluid supply and the outlet port to your application system.
• Pastikan semua sambungan selamat dan bebas bocor.

Figure 3: Pump dimensions for installation planning

4. Arahan Operasi

The Remco 5.3 GPM Demand Pump operates in a demand mode, meaning it will run when there is a demand for fluid and shut off when the demand ceases or pressure is reached.

4.1 Permulaan Permulaan

1. Ensure all fluid connections are tight and the pump is securely mounted.
2. Verify the fluid source is open and available to the pump.
3. Connect the pump to the 12 VDC power supply. The pump may run briefly to prime itself.
4. Open the discharge valve or nozzle to allow fluid to flow. The pump will start automatically.
5. Once the system is primed and air is purged, the pump will operate smoothly.

4.2 Chemical Application

This pump is designed for use with various agricultural chemicals, including herbicides, fertilizers, and insecticides. Always ensure the chemicals used are compatible with Viton valves and Santoprene diaphragms to prevent damage.

• Refer to the chemical manufacturer's guidelines for proper mixing ratios and application rates.
• Avoid running the pump dry for extended periods, as this can cause damage. The pump has dry run capability for short durations.

5. Penyelenggaraan

Regular maintenance will extend the life and ensure the reliable operation of your Remco pump.

5.1 Post-Use Cleaning

• After every use, especially when pumping chemicals, it is highly recommended to rinse the pump thoroughly with clean water.
• Run clean water through the pump for several minutes to flush out any residual chemicals.

5.2 Pengurusan Suhu

• The maximum liquid temperature is 140°F (60°C).
• The maximum motor temperature is 180°F (82°C). However, for user safety, optimal performance, and maximum motor life, the motor surface temperature should not exceed 150°F (66°C).
• Monitor the pump's temperature during prolonged operation. If it becomes excessively hot, allow it to cool down.

5.3 Penyimpanan

• If storing the pump for an extended period, ensure it is thoroughly cleaned and drained of all liquids.
• Store in a dry, frost-free environment.

6. Penyelesaian masalah

This section provides solutions to common issues you might encounter with your Remco pump. If the problem persists, contact customer support.

7. Spesifikasi Teknikal

8. Waranti dan Sokongan

For warranty information, technical support, or replacement parts, please contact Remco customer service. Keep your purchase receipt and model number handy when contacting support.

For more information, visit the official Remco webtapak atau hubungi talian sokongan pelanggan mereka.