TE Connectivity QC210AC Protective Label Covers Instruction Manual

1. Pengenalan

1.1 Produk Selesaiview

The TE Connectivity QC210AC is a protective label cover designed to shield and preserve labels in various environments. Constructed from durable, transparent vinyl, these covers ensure the legibility and longevity of underlying labels.

• Bahan: Vinyl
• Ketelusan: Transparent for clear visibility of labels
• Dimensi: Approximately 50.8mm width
• Fungsi: Provides a protective layer over existing labels

1.2 Tujuan Penggunaan

These protective label covers are intended for use in industrial, electrical, and general applications where labels require protection from abrasion, moisture, dirt, and other environmental factors. They are suitable for safeguarding identification labels, warning labels, and instructional labels.

2. Persediaan dan Persediaan

2.1 Bahan Yang Diperlukan

• TE Connectivity QC210AC Protective Label Covers
• Labels to be protected
• Kain bersih dan tidak berbulu
• Mild cleaning solution (e.g., isopropyl alcohol) if necessary

2.2 Penyediaan Permukaan

Before applying the protective cover, ensure the surface of the label and the surrounding area are clean, dry, and free from dust, oil, grease, or any other contaminants. Use a clean, lint-free cloth and a mild cleaning solution if needed, allowing the surface to dry completely before application.

3. Arahan Permohonan

Follow these steps for proper application of the QC210AC protective label cover:

1. Prepare the Label: Ensure the label you intend to cover is securely affixed and the surface is clean and dry as per Section 2.2.
2. Peel Backing: Carefully peel a small section of the release liner from one end of the QC210AC protective cover, exposing the adhesive side. Avoid touching the adhesive.
3. Selaraskan dan Gunakan: Align the exposed adhesive edge of the protective cover precisely over one edge of the label. Once aligned, slowly and steadily press the cover down, gradually peeling off the remaining release liner while smoothing the cover over the label.
4. Lancar Keluar: Use your fingers or a soft, flat tool (e.g., a squeegee) to gently smooth out any air bubbles from the center outwards. Ensure firm contact across the entire surface of the label for optimal adhesion and protection.

Rajah 1: Illustration demonstrating the application of the protective label cover over an existing label. The image shows a transparent rectangular cover with one corner slightly lifted, revealing the instruction 'APPLY OVER LABEL' printed on its surface, indicating its intended use.

4. Penjagaan dan Penyelenggaraan

The QC210AC protective label covers are designed for durability. To maintain their clarity and protective qualities:

• Pembersihan: If the cover becomes dirty, gently wipe it with a clean, soft, damp cloth. A mild soap solution can be used for stubborn dirt, followed by wiping with a clean, damp kain untuk mengeluarkan sebarang sisa.
• Elakkan Bahan Kimia Keras: Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the vinyl material and affect its transparency or adhesive properties.
• Pemeriksaan: Periodically inspect the covers for any signs of damage or peeling. Replace damaged covers to ensure continued protection of the underlying label.

5. Penyelesaian masalah

This section addresses common issues that may arise during or after application.

• Issue: Air Bubbles Under the Cover
  Penyelesaian: During application, ensure you smooth the cover from one end to the other, gradually removing the release liner. If bubbles appear, gently lift the edge of the cover closest to the bubble and re-apply, smoothing it down firmly. A soft squeegee can help.
• Issue: Poor Adhesion
  Penyelesaian: Ensure the label surface was thoroughly cleaned and dried before application. Contaminants like dust, oil, or moisture can prevent proper adhesion. Re-clean the surface if possible, or use a new cover if the adhesive has been compromised.
• Issue: Cover Peeling at Edges
  Penyelesaian: This can occur if the edges were not pressed down firmly during application or if the surface was not clean. Ensure all edges are pressed down securely. In environments with high traffic or abrasion, consider applying additional pressure to the edges during initial application.

6. Spesifikasi

7. Waranti dan Sokongan

For specific warranty information or technical support regarding the TE Connectivity QC210AC Protective Label Covers, please contact TE Connectivity directly through their official website or customer service channels. Ensure you have your product model number (QC210AC) available when seeking support.