Manual+

Linear MCT-3 DNT00089

Linear MCT-3 Megacode 3-Channel Remote Control User Manual

Model: MCT-3 DNT00089

1. Pengenalan

This manual provides instructions for the Linear MCT-3 Megacode 3-Channel Remote Control, model DNT00089. This remote is designed for use with Linear's Mega Code series of receivers, commonly found in garage door openers and automatic gate systems. It allows for the control of up to three separate devices.

The Linear MCT-3 remote transmits a unique code for each of its three buttons. This enables control of multiple devices, such as a garage door opener, an access gate, and an additional garage door operator, all from a single remote.

Comparison of Linear DNT00093 and DNT00089 remote controls

Imej 1.1: Comparison showing the Linear DNT00093 (left) and DNT00089 (right) remote controls. The DNT00093 is a replacement for the DNT00089, indicating functional equivalence.

2. Ciri-ciri Produk

  • Three-Channel Operation: Controls up to three separate Linear Mega Code compatible devices.
  • Mega Code Technology: Utilizes secure, encrypted radio frequency transmission.
  • Visor Clip Design: Easily attaches to a vehicle's sun visor for convenient access.
  • Padat dan Tahan Lama: Designed for everyday use.
  • Pengaturcaraan Mudah: Simple "Learn" button programming with compatible receivers.
Linear MCT-3 Megacode 3-Channel Remote Control

Imej 2.1: Depan view of the Linear MCT-3 Megacode 3-Channel Remote Control, showing its three distinct buttons.

3. Persediaan dan Pengaturcaraan

To program your Linear MCT-3 remote control, follow these steps. Ensure you are near your garage door opener or gate receiver during this process.

  1. Locate the Receiver's Learn Button: On your garage door opener or gate receiver, find the "Learn" button. The location of this button varies by model, but it is typically on the motor unit itself. Refer to your opener's manual if you cannot locate it.
  2. Aktifkan Mod Pembelajaran: Press and release the "Learn" button on your receiver. The indicator light on the receiver will typically illuminate or flash, indicating it is in programming mode. You usually have about 30 seconds to complete the next step.
  3. Programkan Alat Kawalan Jauh: While the receiver is in learn mode, press and hold the desired button on your Linear MCT-3 remote control that you wish to use for this device.
  4. Sahkan Pengaturcaraan: Release the remote button once the receiver's indicator light changes (e.g., turns off, flashes rapidly, or the garage door/gate moves slightly). This confirms successful programming.
  5. Operasi Ujian: Press the programmed button on your remote control to ensure it activates the garage door or gate.

Nota: If you wish to program additional buttons on the remote for other devices, repeat steps 2-5 for each device, selecting a different button on the remote each time.

4. Operasi

Once programmed, operating your Linear MCT-3 remote control is straightforward:

  • Aktifkan Peranti: Press the corresponding button on the remote control that has been programmed to your garage door opener or gate.
  • Julat: For optimal performance, ensure you are within a reasonable operating range of your receiver. Environmental factors can affect signal range.

5. Penyelenggaraan: Penggantian Bateri

The Linear MCT-3 remote control requires one 9V battery. If the remote's indicator light does not illuminate when a button is pressed, or if the range significantly decreases, the battery may need replacement.

  1. Buka Alat Kawalan Jauh Casing: Locate the battery compartment cover on the back of the remote. This may require a small screwdriver or prying tool to open carefully.
  2. Keluarkan Bateri Lama: Carefully remove the old 9V battery from its terminals.
  3. Masukkan Bateri Baharu: Insert a new 9V alkaline battery, ensuring the positive (+) and negative (-) terminals are correctly aligned.
  4. Tutup Casing: Pasang semula penutup petak bateri, pastikan ia dipasang dengan kukuh.
  5. Ujian: Test the remote's operation with your programmed device.

Pelupusan: Please dispose of old batteries responsibly according to local regulations.

6. Penyelesaian masalah

MasalahKemungkinan PuncaPenyelesaian
Remote does not activate device.
  • Bateri mati atau lemah.
  • Remote not programmed correctly.
  • Luar kawasan.
  • Kerosakan penerima.
  • Replace the 9V battery (refer to Section 5).
  • Re-program the remote (refer to Section 3).
  • Bergerak lebih dekat kepada penerima.
  • Check the receiver's power and functionality.
Mengurangkan julat operasi.
  • Bateri lemah.
  • Interference from other radio frequency devices.
  • Halangan antara alat kawalan jauh dan penerima.
  • Ganti bateri 9V.
  • Identify and mitigate sources of interference.
  • Ensure a clear line of sight if possible.
Lampu penunjuk pada alat kawalan jauh tidak menyala.
  • Bateri mati atau tidak dipasang dengan betul.
  • Check and replace the 9V battery.

7. Spesifikasi

CiriPerincian
Nombor ModelMCT-3 DNT00089 (Replaced by DNT00093)
JenamaLinear
Bilangan Saluran3
Teknologi KetersambunganRadio Frequency (Mega Code)
Peranti SerasiLinear Mega Code Receivers
Sumber KuasaBateri 1 x 9V
Dimensi ProdukKira-kira 2 x 1 x 1 inci
Berat BarangKira-kira 0.141 auns

8. Waranti dan Sokongan

For specific warranty information and technical support regarding your Linear MCT-3 Megacode 3-Channel Remote Control, please refer to the documentation provided with your purchase or contact Linear directly through their official webtapak. Simpan bukti pembelian anda untuk tuntutan waranti.

Untuk bantuan lanjut, anda boleh melawati Linear webtapak (cthamppautan le, pautan sebenar mungkin berbeza-beza).