SkyTech 1410T/LCD Timer Fireplace Remote Control User Manual

pengenalan

This manual provides instructions for the safe and efficient operation of your SkyTech 1410T/LCD Timer Fireplace Remote Control system. This system is designed to offer convenient remote control for gas heating appliances, featuring a timer function and an LCD display for room temperature.

Maklumat Keselamatan

• Read all instructions thoroughly before installation and use.
• Ensure all electrical wiring is performed by a qualified professional to prevent electrical shock or fire hazards.
• Do not expose the remote control or receiver to water or excessive moisture.
• Replace batteries promptly when the low battery indicator appears on the remote's display.
• Keep the remote control out of reach of children to prevent unintended operation of the fireplace.
• Always ensure the fireplace area is clear of flammable materials before operation.

Kandungan Pakej

Sahkan bahawa semua komponen terdapat dalam pakej anda:

• 1 x Remote Control Transmitter (4-button: On/Off/Timer/Set, with LCD display)
• 1 x Receiver Box (110V AC, with learn function and On/Remote/Off slider switch)
• 2 x AAA Alkaline Batteries (for transmitter)

Persediaan dan Pemasangan

1. Pemasangan Bateri (Pemancar)

Open the battery compartment located on the back of the remote control. Insert two AAA alkaline batteries, ensuring correct polarity (+/-). Close the compartment securely.

2. Receiver Placement and Wiring

The receiver box operates on 110-120 VAC and provides a "dry contact" output to your fireplace. It can be placed on the hearth or discreetly under the fireplace behind the control access panel.

Amaran: Installation should be performed by a qualified technician. Always ensure power to the fireplace is disconnected at the circuit breaker before performing any wiring.

Connect the receiver's wires to the appropriate terminals on your gas heating appliance. These terminals are typically where a wall switch or existing remote receiver would connect. The receiver includes male-female connectors for straightforward integration.

Image: The SkyTech 1410T/LCD remote control transmitter alongside its receiver unit. The receiver has a power cord and a slider switch for ON/REMOTE/OFF modes.

Imej: Depan view of the SkyTech 1410T/LCD remote control transmitter, showing the LCD display and four control buttons: ON, OFF, TIMER, and SET.

3. Pairing the Transmitter and Receiver (Learning Function)

1. Ensure the receiver is powered on and its slider switch is set to the "REMOTE" position.
2. Locate the "LEARN" button on the receiver box. Press and hold this button until you hear a beep or see an indicator light flash.
3. Within 20 seconds of pressing the "LEARN" button, press the "ON" button on the remote control transmitter.
4. A confirmation beep from the receiver indicates successful pairing. The system operates on one of 65,536 security codes programmed at the factory.

Arahan Operasi

Operasi Asas

• Butang HIDUP: Press to turn the fireplace ON. The LCD will display the current room temperature.
• Butang MATI: Press to turn the fireplace OFF.

Fungsi Pemasa

The remote features a convenient 3-hour countdown timer for automatic fireplace shutdown.

1. With the fireplace ON, press the "TIMER" button. The LCD will display "3:00" and begin counting down.
2. To adjust the timer duration, press the "SET" button while the timer is active. Each press will cycle through available timer durations (e.g., 1 hour, 2 hours, 3 hours).
3. The fireplace will automatically turn OFF when the timer reaches zero.
4. To cancel the timer at any point, press the "OFF" button.

Paparan Suhu

The LCD on the transmitter displays the current ambient room temperature in either Fahrenheit (°F) or Celsius (°C). It is important to note that this unit is not a thermostat and does not control the fireplace based on a set temperature. It only provides a reading of the room's temperature.

Childproof Feature

To activate the childproof feature, press and hold the "ON" and "OFF" buttons simultaneously for approximately 5 seconds until "CP" appears on the LCD. When active, the remote will not respond to button presses. To deactivate, repeat the process until "CP" disappears from the display.

Penyelenggaraan

Penggantian Bateri

When the low battery indicator appears on the LCD, replace the two AAA batteries in the transmitter promptly. Use only alkaline batteries for optimal performance and longevity.

Pembersihan

Wipe the remote control and receiver with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the units in liquids, as this can cause damage.

Menyelesaikan masalah

Spesifikasi

Waranti dan Sokongan

For warranty information or technical assistance, please contact SkyTech customer support. Refer to the product packaging or the manufacturer's official website for current contact details. It is recommended to keep your purchase receipt as proof of purchase for any warranty claims.