pengenalan
This manual provides essential instructions for the proper setup, operation, and maintenance of your Intermec SR30 Linear Imager RS232 Barcode Scanner. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Intermec SR30 is a high-performance linear imager designed for reliable barcode scanning in various environments, connecting via an RS232 interface.
Maklumat Keselamatan
- Jangan dedahkan pengimbas kepada suhu, kelembapan atau cahaya matahari langsung yang melampau.
- Elakkan daripada menjatuhkan pengimbas atau menyebabkannya terkena hentaman yang teruk.
- Do not attempt to open or modify the scanner. Refer all servicing to qualified personnel.
- Use only the power supply and cables provided or approved by Intermec.
- Keep the scanning window clean to ensure accurate barcode reading.
Kandungan Pakej
Sahkan bahawa pakej anda mengandungi item berikut:
- Intermec SR30 Linear Imager Barcode Scanner
- RS232 Interface Cable
- Unit Bekalan Kuasa
- Dokumentasi (manual ini atau yang serupa)
Jika terdapat sebarang barang yang hilang atau rosak, sila hubungi pembekal anda dengan segera.
Persediaan
1. Menyambungkan Pengimbas
- Connect the RS232 Cable: Plug the RS232 connector of the interface cable into the corresponding serial port on your host computer or POS system.
- Sambungkan ke Pengimbas: Plug the other end of the interface cable into the port at the base of the SR30 scanner. Ensure a secure connection.
- Sambungkan Bekalan Kuasa: Connect the power supply unit to the power port on the interface cable or directly to the scanner base, as applicable for your specific cable configuration. Plug the power supply into a standard electrical outlet.
2. Kuasa Awal Hidup
Once connected, the scanner should power on automatically. Observe the indicator lights (typically an LED) for initial status. The scanner may emit a short beep to indicate it is ready for operation.
3. Basic Configuration (if required)
The SR30 scanner may require configuration for specific RS232 communication parameters (e.g., baud rate, data bits, parity) to match your host system. Refer to the detailed programming guide (often a separate document with programming barcodes) for advanced configuration. For basic operation, the default settings are often sufficient.
Mengendalikan Pengimbas
1. Mengimbas Kod Bar
- Matlamat: Point the scanning window of the SR30 at the barcode you wish to read. Ensure the entire barcode is within the scanner's field of view.
- Imbas: Press and hold the trigger button (if applicable) or present the barcode to the scanner's window for automatic scanning.
- Pengesahan: A successful scan is typically indicated by an audible beep and/or a change in the LED indicator light (e.g., green light). The barcode data will be transmitted to your host system.
2. Memahami Petunjuk
- LED hijau: Indicates a successful barcode read.
- Red/Amber LED: May indicate an error, scanner busy, or awaiting input. Consult the full programming guide for specific error codes or patterns.
- Beep Sounds: Different beep patterns can indicate successful reads, errors, or configuration changes.
Penyelenggaraan
Membersihkan Pengimbas
- Regularly clean the scanning window with a soft, lint-free cloth dampdisapu dengan air atau pembersih yang lembut dan tidak melelas.
- Do not use harsh chemicals, solvents, or abrasive materials, as these can damage the scanner's surface.
- Pastikan pengimbas dimatikan sebelum membersihkan.
Penyimpanan
Apabila tidak digunakan, simpan pengimbas di persekitaran yang bersih dan kering, jauh daripada cahaya matahari langsung dan suhu yang melampau.
Menyelesaikan masalah
| Masalah | Kemungkinan Punca | Penyelesaian |
|---|---|---|
| Pengimbas tidak dihidupkan. | Power cable not connected; power outlet faulty; power supply unit failure. | Check all cable connections. Try a different power outlet. Ensure the power supply is functioning. |
| Pengimbas tidak membaca kod bar. | Barcode damaged or poorly printed; scanning window dirty; incorrect symbology enabled; scanner not configured for host. | Ensure barcode is clear. Clean scanning window. Verify scanner configuration matches host system requirements. Try scanning a known good barcode. |
| Barcode data not appearing on host. | RS232 cable loose or faulty; incorrect RS232 communication settings (baud rate, parity); host application not ready. | Check RS232 cable connection. Verify RS232 settings on both scanner and host. Ensure host application is active and ready to receive input. |
Spesifikasi
- model: SR30
- Nombor Bahagian: 225-727-003 (Kit)
- Jenis Pengimbas: Pengimej Linear
- Antara muka: RS232
- Pengeluar: Intermec
- Berat Barang: 0.01 ounces (approximate, scanner only)
- Jabatan: Kod bar
- ASIN: B003T0WF3S
Waranti dan Sokongan
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Intermec webtapak. Simpan resit pembelian anda sebagai bukti pembelian untuk tuntutan waranti.
Contact your reseller or Intermec customer service for assistance with issues not covered in this manual.
