1. Pengenalan dan Lebihview
The M-Wave Bike Alarm ALL/234000 is a compact and effective security device designed to protect your bicycle from theft. It features a sensitive motion sensor that triggers a loud 120 dB alarm upon detecting unauthorized movement. The alarm includes adjustable sensitivity settings and a user-settable three-number encoding system for activation and deactivation. Its robust design and easy mounting bracket make it a practical addition to your bicycle security measures.
This manual provides detailed instructions for the proper setup, operation, and maintenance of your M-Wave Bike Alarm to ensure optimal performance and longevity.
2. Maklumat Keselamatan
- Penggera Kuat: The alarm produces a very loud sound (120 dB). Avoid direct exposure to the alarm sound at close range to prevent potential hearing discomfort.
- Keselamatan Bateri: Ensure batteries are inserted correctly according to polarity markings. Do not mix old and new batteries, or different types of batteries. Dispose of used batteries responsibly. Keep batteries out of reach of children.
- Tahan Air: While designed for outdoor use, avoid submerging the device in water or exposing it to heavy, prolonged rain.
- Pemasangan: Ensure the alarm is securely mounted to prevent it from falling off during cycling, which could cause damage or injury.
- Kanak-kanak: This product is not a toy. Keep it away from small children.
3. Kandungan Pakej
Sila sahkan bahawa semua item terdapat dalam pakej anda:
- M-Wave Bike Alarm Unit (Model ALL/234000)
- Mounting Bracket (for tubes 25-30 mm)
- Batteries (1 product-specific battery, included and often pre-installed)
Figure 1: Retail packaging of the M-Wave Bike Alarm, displaying the alarm unit and mounting bracket inside a clear plastic blister pack. Text on the packaging indicates 'BIKE ALARM LOCK' and '110 db' loudness.
4. Persediaan
4.1 Pemasangan Bateri
The M-Wave Bike Alarm comes with one product-specific battery included, which may be pre-installed. If not, or if replacement is needed:
- Locate the battery compartment cover on the back or bottom of the alarm unit.
- Use a small screwdriver (if required) to open the compartment.
- Insert the battery, ensuring correct polarity (+/-) as indicated inside the compartment.
- Tutup petak bateri dengan selamat.
4.2 Memasang Penggera
The alarm unit can be mounted on bicycle tubes with a diameter between 25 mm and 30 mm.
- Choose a suitable, discreet location on your bicycle frame or seat post where the alarm will not interfere with riding or other components.
- Attach the mounting bracket to the chosen tube using the provided screws or straps, ensuring it is firmly secured.
- Slide the M-Wave Bike Alarm unit onto the bracket until it clicks into place. Ensure it is securely fastened and does not wobble.
Rajah 2: Depan view of the M-Wave Bike Alarm, showing the main unit with 'ALARM' text, M-Wave logo, and three control buttons (red, green, blue) on top. The mounting bracket is visible on the right side.
4.3 Setting the 3-Digit Encoding
The alarm uses a 3-digit code for arming and disarming. You can set your personal code using the three colored buttons (Red, Green, Blue) on top of the unit.
- Masukkan Mod Persediaan: With the alarm disarmed, press and hold the merah button for approximately 5 seconds until you hear a short beep, indicating setup mode.
- Set First Digit: Press one of the three colored buttons (Red, Green, or Blue) to select your first digit. You will hear a confirmation beep.
- Set Second Digit: Press one of the three colored buttons again for your second digit. Confirmation beep.
- Set Third Digit: Press one of the three colored buttons for your third digit. Confirmation beep.
- Confirm Code: After entering the third digit, the alarm will emit a longer beep, confirming your new 3-digit code is set. Remember this sequence.
Note: If you forget your code, you may need to remove and reinsert the battery to reset the alarm to its factory default code (e.g., Red-Red-Red), then set a new code.
5. Arahan Operasi
5.1 Arming the Alarm
To arm the alarm and activate the motion sensor:
- Tekan ke hijau butang sekali.
- The alarm will emit a short beep to confirm it is armed.
- There will be a delay of approximately 5-10 seconds before the motion sensor becomes fully active, allowing you to move away from the bicycle without triggering the alarm.
5.2 Melumpuhkan Penggera
To disarm the alarm and deactivate the motion sensor:
- Enter your 3-digit code by pressing the corresponding colored buttons in sequence (e.g., Red-Green-Blue).
- A longer beep will confirm that the alarm has been successfully disarmed.
5.3 Melaraskan Kepekaan
The alarm's motion sensor sensitivity can be adjusted to suit your environment and preferences.
- With the alarm disarmed, press the Biru butang.
- Each press will cycle through different sensitivity levels (e.g., Low, Medium, High). The alarm may indicate the current level with a specific number of beeps (e.g., 1 beep for Low, 2 for Medium, 3 for High).
- Select the desired sensitivity level. Higher sensitivity will trigger the alarm with less movement, while lower sensitivity requires more significant disturbance.
5.4 Alarm Trigger
When the alarm is armed and motion is detected:
- The alarm will emit a series of loud warning beeps.
- If the motion continues or is detected again within a short period, the full 120 dB alarm will sound for a set duration (e.g., 15-20 seconds).
- The alarm will reset and re-arm itself after sounding, ready to detect further movement.
6. Penyelenggaraan
6.1 Penggantian Bateri
When the battery is low, the alarm may emit a specific low-battery warning sound (e.g., intermittent chirps) or its performance may degrade. Replace the battery as described in Section 4.1. Always use the specified battery type.
6.2 Pembersihan
Clean the alarm unit with a soft, damp cloth. Do not use abrasive cleaners, solvents, or immerse the unit in water. Ensure the unit is dry before use.
6.3 Penyimpanan
If storing the alarm for an extended period, it is recommended to remove the battery to prevent leakage and damage to the unit.
7. Penyelesaian masalah
| Masalah | Kemungkinan Punca | Penyelesaian |
|---|---|---|
| Alarm does not arm/disarm. | Low battery; Incorrect code entered. | Replace battery; Re-enter code carefully; Reset code if forgotten (Section 4.3). |
| Alarm triggers too easily (false alarms). | Sensitivity set too high; Loose mounting. | Adjust sensitivity to a lower level (Section 5.3); Ensure alarm is securely mounted. |
| Alarm does not trigger with movement. | Sensitivity set too low; Dead battery; Alarm not armed. | Adjust sensitivity to a higher level (Section 5.3); Replace battery; Arm the alarm (Section 5.1). |
| Alarm sound is weak or distorted. | Bateri lemah. | Gantikan bateri. |
8. Spesifikasi
- model: ALL/234000
- Jenama: M-Wave
- Dimensi: 10 x 3.5 x 0.6 cm (lebih kurang)
- Berat: 158 g (anggaran)
- Kekuatan Penggera: 120 dB
- Mounting Bracket Diameter: Suitable for tubes 25 - 30 mm
- Sumber Kuasa: 1 Produk Bateri khusus (termasuk)
- ciri-ciri: Motion sensor, adjustable sensitivity, 3-digit encoding
9. Waranti dan Sokongan
For warranty information and customer support, please refer to the documentation provided at the time of purchase or contact your retailer. M-Wave products are designed for reliability and performance. If you encounter any issues not covered in this manual, please reach out to M-Wave customer service or your authorized dealer for assistance.
