Manual Arahan Sistem Kilang Air 3M FM-1500 05-61002

1. Pengenalan

This manual provides comprehensive instructions for the installation, operation, and maintenance of the 3M Water Factory System FM-1500 05-61002 Drinking Water System. Please read this manual thoroughly before attempting to install or operate the system. Retain this manual for future reference.

The 3M Water Factory System FM-1500 is designed to provide cleaner, better-tasting water by reducing lead, sediment, asbestos, cysts, and chlorine. It features a sanitary quick-change design for ease of use.

2. Maklumat Keselamatan

AMARAN: Produk ini mengandungi bahan kimia yang diketahui oleh Negeri California boleh menyebabkan kanser dan kecacatan kelahiran atau kemudaratan pembiakan yang lain. Untuk maklumat lanjut, sila layari www.P65Warnings.ca.gov.

• Always follow local plumbing codes and regulations during installation.
• Jangan gunakan dengan air yang tidak selamat secara mikrobiologi atau kualiti yang tidak diketahui tanpa pembasmian kuman yang mencukupi sebelum atau selepas sistem.
• Pastikan semua sambungan selamat untuk mengelakkan kebocoran.
• Do not expose the system to freezing temperatures.
• Use only genuine 3M replacement filters to ensure proper performance and to avoid voiding the warranty.

3. Persediaan dan Pemasangan

The 3M Water Factory System FM-1500 is an under-sink drinking water system. Professional installation is recommended. Ensure adequate space is available under the sink for the unit, which measures approximately 18.25 x 3.5 x 3.5 inches.

3.1 Komponen Termasuk

• DRINKING WATER FILTRATION SYSTEM (main unit)
• Installation hardware (may vary, refer to packaging)

3.2 Langkah Pemasangan (Garis Panduan Am)

1. Matikan bekalan air: Cari dan matikan injap bekalan air sejuk di bawah sink.
2. Install faucet (if applicable): If a dedicated faucet is included, install it according to its specific instructions.
3. Mount the filter head: Securely mount the filter head assembly to the cabinet wall under the sink using appropriate fasteners.
4. Sambungkan saluran air: Connect the cold water supply line to the inlet of the filter head and the filtered water line to the faucet. Ensure all connections are tight.
5. Insert filter cartridge: Align the filter cartridge with the filter head and twist until it locks into place. The sanitary quick-change design allows for easy, mess-free replacement.
6. Siram sistem: Slowly turn on the cold water supply. Open the filtered water faucet and allow water to run for several minutes (e.g., 5-10 minutes) to flush out air and carbon fines.
7. Semak kebocoran: Periksa semua sambungan untuk sebarang tanda kebocoran.

4. Arahan Operasi

Once installed and flushed, the 3M Water Factory System FM-1500 operates automatically when the filtered water faucet is opened. For optimal performance, adhere to the following guidelines:

• Penggunaan Awal: After installation or filter replacement, run water through the system for 5-10 minutes to ensure proper flushing.
• Penggunaan Harian: Use the dedicated filtered water faucet for drinking and cooking.
• Kadar Aliran: The system is designed for a flow rate of 1.5 gallons per minute (GPM).
• Tekanan: Operate within a pressure range of 25-125 PSI (172-862 kPa).
• Suhu: The maximum operating temperature is 100°F (38°C). Do not use with hot water.

5. Penyelenggaraan

Regular maintenance ensures the continued performance and longevity of your 3M Water Factory System FM-1500.

5.1 Penggantian Kartrij Penapis

The filter cartridge has a capacity of 1,500 gallons (5,678 liters) or should be replaced every 6 months, whichever comes first. Replacement is crucial for maintaining water quality.

1. Matikan bekalan air: Turn off the cold water supply to the system.
2. Melegakan tekanan: Open the filtered water faucet to relieve pressure.
3. Remove old cartridge: Twist the old filter cartridge counter-clockwise to unlock and remove it. The sanitary quick-change design minimizes contact with used filter media.
4. Install new cartridge: Remove protective covers from the new 3M replacement cartridge. Align the new cartridge with the filter head and twist clockwise until it locks securely into place.
5. Restore water supply: Slowly turn on the cold water supply.
6. Siram sistem: Open the filtered water faucet and run water for 5-10 minutes to flush the new filter.
7. Semak kebocoran: Inspect for any leaks around the new cartridge.

5.2 Pembersihan

Periodically wipe down the exterior of the system with a clean, damp kain. Jangan gunakan pembersih atau pelarut yang melelas.

6. Penyelesaian masalah

This section addresses common issues you might encounter with your drinking water system.

• Aliran Air Rendah:
  • Check if the cold water supply valve is fully open.
  • The filter cartridge may be clogged or at the end of its service life. Replace the filter.
  • Ensure there are no kinks in the water lines.
• Rasa atau Bau yang Luar Biasa:
  • The filter cartridge may need replacement.
  • Ensure the system was properly flushed after installation or filter change.
• Kebocoran:
  • Matikan bekalan air dengan segera.
  • Periksa semua sambungan untuk sesak.
  • Ensure the filter cartridge is correctly seated and locked into the filter head.

If problems persist after following these steps, contact 3M customer support.

7. Spesifikasi

8. Waranti dan Sokongan

For warranty information and customer support, please refer to the documentation included with your product or visit the official 3M webtapak. Anda juga boleh melawat Kedai 3M di Amazon untuk sumber tambahan.