Perintah 17068

Manual Arahan

Command 3M 17068 Wire Hooks With Strips

Model: 17068 | Brand: Command

Produk Selesaiview

The Command 3M 17068 Wire Hooks with Strips offer a damage-free solution for hanging items in your home or office. Designed to hold strongly on various surfaces, these hooks can be removed cleanly without leaving holes, marks, or sticky residue. Each pack contains two medium wire hooks and four medium adhesive strips, capable of holding up to 3 pounds (1.36 kg) per hook.

Command 3M 17068 Wire Hooks packaging showing two white hooks and adhesive strips.

Imej 1: Depan view of the Command 3M 17068 Wire Hooks packaging. It displays two white wire hooks and the included adhesive strips, highlighting key features like strong hold and clean removal. The 3M logo is visible at the top right.

Persediaan dan Pemasangan

Proper installation ensures maximum holding power and clean removal. Follow these steps carefully:

  1. Bersihkan Permukaan: Select a smooth, clean surface. Wipe the area with rubbing alcohol (isopropyl alcohol). Do not use household cleaners as they may leave a residue. Allow the surface to dry completely.
  2. Prepare the Strip: Separate the Command Adhesive Strips. Remove the red liner from one side of the strip.
  3. Apply to Hook: Press the adhesive strip firmly onto the back of the hook. Ensure the tab of the strip extends slightly below the hook for easy removal later.
  4. Sapukan pada Dinding: Remove the black liner from the other side of the strip. Position the hook on the desired surface. Press the hook firmly against the wall for 30 seconds.
  5. Tunggu: For maximum adhesion, wait 1 hour before hanging anything on the hook. This allows the adhesive to build strength.
Command 3M 17068 Wire Hooks packaging showing installation instructions.

Imej 2: Packaging of Command Wire Hooks, illustrating the "Damage-Free Hanging" feature. The image shows the two hooks and highlights the 1 kg (3 lb) weight capacity. The reverse side of the packaging often contains visual installation instructions.

Operasi dan Penggunaan

Once installed, your Command Wire Hooks are ready for use. They are designed for indoor use and can hold items up to 3 pounds (1.36 kg). Ensure the weight of the item you intend to hang does not exceed this limit.

  • Jangan gantung barang berharga atau tidak boleh ditukar ganti.
  • Jangan menggantung di atas katil.
  • Do not use on wallpaper, vinyl surfaces, or other delicate surfaces.
  • Ensure the hook is securely attached before hanging any item.

Penyelenggaraan dan Penyingkiran

Command Hooks require minimal maintenance. If you need to move or remove a hook, follow these steps for clean removal:

  1. Alih Keluar Item: Take off any item hanging on the hook.
  2. Hold Hook: Gently hold the top of the hook. Do not press the hook against the wall.
  3. Stretch Strip: Slowly stretch the adhesive strip straight down along the wall, keeping your hand against the wall. Stretch the strip at least 6 inches (15 cm) until the hook releases from the wall. Do not pull the strip outwards or upwards.
  4. Permohonan semula: If you wish to re-use the hook, you will need a new Command Medium Adhesive Strip.

To clean the hooks, simply wipe them with a damp kain. Jangan gunakan pembersih yang kasar.

Menyelesaikan masalah

  • Hook fell off:
    • Ensure the surface was cleaned with rubbing alcohol and allowed to dry completely before application.
    • Verify that the strip was pressed firmly against the hook and the wall for 30 seconds each.
    • Confirm that the 1-hour waiting period was observed before hanging items.
    • Check if the weight of the item exceeded the 3-pound limit.
  • Residue left on wall after removal:
    • The strip might not have been stretched straight down or stretched enough (at least 6 inches).
    • Ensure the strip was not pulled outwards or upwards during removal.
  • Hook not sticking to surface:
    • The surface might be textured, porous, or painted with a low-VOC paint, which can affect adhesion. Command hooks work best on smooth, solid surfaces.
    • Ensure the surface is not wallpaper or vinyl, as these are not recommended.

Spesifikasi

JenamaPerintah
Nombor Model17068
warnaputih
bahanplastik
Jenis PemasanganLekap di dinding
Had berat3 paun (1.36 kg)
Penggunaan yang DisyorkanDalaman
Dimensi Item (L x W x H)6.7 x 3.6 x 2 inci (17.02 x 9.14 x 5.08 cm)
Berat Barang1.6 auns (45.36 gram)
Bilangan Cangkuk2 setiap pek
UPC051131921276
Tarikh Mula-mula Tersedia18 September 2009

Waranti dan Sokongan

Specific warranty information for the Command 3M 17068 Wire Hooks is typically provided on the product packaging or through the manufacturer's official website. For detailed warranty terms, product support, or to purchase replacement strips, please visit the official Command brand weblaman web atau hubungi khidmat pelanggan 3M.

You can often find more information and support resources by visiting the Command Store on Amazon.

Dokumen Berkaitan - 17068

Praview Command 17006CLR-ES Clear Mini Hooks: Panduan Aplikasi dan Pembuangan
Arahan langkah demi langkah untuk menggunakan dan mengeluarkan Command Clear Mini Hooks (model 17006CLR-ES) menggunakan jalur pelekat yang jelas. Termasuk petua penggunaan dan maklumat waranti.
Praview Command Hooks: Easy On and Off Installation Guide
Step-by-step instructions for applying and removing Command Hooks, ensuring a secure hold and damage-free removal. Includes guides for both installation and removal.
Praview Arahan Pemasangan dan Penyingkiran Cangkuk Perintah
Panduan langkah demi langkah untuk memasang dan menanggalkan cangkuk Command, termasuk maklumat produk dan butiran waranti untuk model 17003ES.
Praview Dynojet Power Commander 6 Installation Guide for Kawasaki Z125 (PC6-17068)
Detailed installation guide for the Dynojet Power Commander 6 (PC6-17068) on 2017-2020 Kawasaki Z125 motorcycles. Covers parts list, optional accessory inputs, wiring connections, and step-by-step installation procedures.