Manual Pengguna Balast Elektronik Philips HF-R 258 ​​TL-D EII

1. Pengenalan

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Philips HF-R 258 TL-D EII Electronic Ballast. This electronic ballast is designed for use with 58 Watt TL-D fluorescent lamps, operating on 220-240V, 50/60Hz electrical systems.

Sila baca manual ini dengan teliti sebelum pemasangan dan simpan untuk rujukan masa hadapan.

2. Maklumat Keselamatan

Sentiasa patuhi langkah keselamatan berikut:

• Bahaya Elektrik: Installation and maintenance should only be performed by a qualified electrician. Ensure power is disconnected at the circuit breaker before any installation or servicing.
• Voltage Keserasian: Sahkan bahawa bekalan voltage (220-240V, 50/60Hz) matches the ballast's requirements.
• Pembumian yang betul: Ensure the ballast is properly grounded to prevent electrical shock.
• Lamp Keserasian: Use only with compatible 58 Watt TL-D fluorescent lamps.
• Keadaan Persekitaran: Do not expose the ballast to excessive moisture or extreme temperatures.

3. Pemasangan dan Persediaan

The Philips HF-R 258 TL-D EII electronic ballast is designed for easy integration into lighting fixtures. Follow the steps below for proper installation.

3.1. Diagram Pendawaian

Refer to the following diagram for correct electrical connections. Ensure all connections are secure and comply with local electrical codes.

Rajah 3.1: Wiring diagram for the Philips HF-R 258 TL-D EII electronic ballast. This diagram illustrates the connections for the DC input (terminals 13, 14), AC input (terminals 8, 9), ground (terminal 10), and the lamp connections (terminals 1-7) for two TL-D lamps.

3.2. MCB Compatibility

The number of ballasts that can be connected to a Miniature Circuit Breaker (MCB) depends on the MCB type and rating. Consult the table below for guidance.

Rajah 3.2: MCB compatibility table. This table provides information on the maximum number of ballasts relative to different MCB types (B, C, L, I, G, U, II, K, III) and their respective ratings (10A, 16A).

4. Arahan Operasi

Once properly installed, the Philips HF-R 258 TL-D EII electronic ballast operates automatically to power compatible fluorescent lamps.

• Hidupkan kuasa: Apply power to the circuit. The ballast will initiate the lamps.
• Fungsi Peredupan: This ballast supports 1-10V dimming. Connect a compatible 1-10V dimmer to the designated dimming terminals (DC input terminals 13 and 14 as shown in the wiring diagram) to control the light output.
• Permulaan Segera: Electronic ballasts provide instant, flicker-free starting for fluorescent lamps.

5. Penyelenggaraan

The Philips HF-R 258 TL-D EII electronic ballast is designed for long-term, maintenance-free operation. However, general care and proper disposal are important.

• Pembersihan: If cleaning is necessary, disconnect power and wipe the ballast with a dry, soft cloth. Do not use abrasive cleaners or solvents.
• Lamp Penggantian: Semasa menggantikan lamps, ensure power is off. Replace with compatible 58 Watt TL-D fluorescent lamps.
• Kitar semula: Electronic ballasts and fluorescent lamps contain materials that should be recycled responsibly. Consult local regulations for proper disposal and recycling procedures.

For more information on recycling and cleaning, please refer to the manufacturer's guidelines or local waste management services.

6. Penyelesaian masalah

If you experience issues with your Philips HF-R 258 TL-D EII electronic ballast, consider the following common problems and solutions:

• Lamps Not Lighting:
  • Check the power supply to the ballast.
  • Sahkan bahawa lamps are correctly installed and are not faulty.
  • Inspect all wiring connections for looseness or damage.
• Berkelip-kelip Lamps:
  • Pastikan lamps are fully seated in their sockets.
  • Semak voltage bekalan.
  • Lamps may be at the end of their lifespan and require replacement.
• Fungsi Peredupan Tidak Berfungsi:
  • Verify the 1-10V dimmer is compatible and correctly wired to the ballast's dimming terminals.
  • Check the dimmer's power supply and functionality.

If problems persist, contact a qualified electrician or Philips Lighting customer support.

7. Spesifikasi

Key technical specifications for the Philips HF-R 258 TL-D EII Electronic Ballast:

Note: Some specifications in the source data, such as "Puissance: 90 Watts" and conflicting bulb base types (GX5.3, E27), appear to be generic or refer to other products. This ballast is specifically designed for 58 Watt TL-D lamps.

8. Waranti dan Sokongan

Warranty information for your Philips HF-R 258 TL-D EII electronic ballast is typically provided at the point of purchase or with the product packaging. Please retain your proof of purchase for warranty claims.

For technical support, service, or further inquiries, please contact Philips Lighting customer service or visit their official website. Contact details can usually be found on the product packaging or the manufacturer's webtapak.