HP Smart Array P600 RAID Controller User Manual

1. Pengenalan

The HP Smart Array P600 serial attached SCSI (SAS) controller is designed to enhance performance and reliability for HP servers. This advanced RAID controller supports the latest SCSI technology and offers robust RAID capabilities. As a new generation SAS Smart Array controller, the SA-P600 significantly improves data transfer rates, providing twice the bandwidth of a 4-channel U320 array controller. This manual provides essential information for the installation, operation, maintenance, and troubleshooting of your HP Smart Array P600 controller.

2. Persediaan dan Pemasangan

Proper installation is crucial for the optimal performance of your HP Smart Array P600 controller. Follow these steps carefully:

1. Langkah Keselamatan: Before beginning, ensure the server is powered off and disconnected from all power sources. Wear an anti-static wrist strap to prevent electrostatic discharge (ESD) damage to components.
2. Locate PCI-X Slot: Identify an available PCI-X slot on your server's motherboard. The HP Smart Array P600 is designed for PCI-X interfaces.
3. Insert Controller Card: Carefully align the controller card with the PCI-X slot. Apply even pressure to both ends of the card until it is fully seated in the slot. Secure the card with the retaining clip or screw provided by your server chassis.
4. Connect SAS Cables: Connect the appropriate SAS data cables from your SAS hard drives or SAS backplane to the SAS ports (PORT-1, PORT-2) on the HP Smart Array P600 controller. Ensure connections are secure.
5. Connect Battery Backup Unit (BBU): If your model includes a Battery Backup Unit (BBU) for cache protection, ensure it is properly connected to the controller. The 3.6V Ni-MH Battery Pack (HP Spares# 307132-001, HP Part# 274779-001) is typically pre-attached or requires a simple connection.
6. Close Server Chassis: Once all connections are secure, close the server chassis cover.
7. Power On and Configure: Reconnect power to the server and power it on. During the server's boot process, access the Smart Array controller's BIOS or utility to configure RAID arrays and logical drives. Refer to your server's documentation for specific instructions on accessing the controller utility.

3. Operasi dan Konfigurasi

Operating the HP Smart Array P600 involves configuring and managing your storage arrays. This is typically done through the controller's firmware utility or a software management application.

• Accessing the Controller Utility: During server boot-up, a prompt usually appears (e.g., "Press F8 to enter Option ROM Configuration for Arrays"). Follow the on-screen instructions to enter the utility.
• Creating Logical Drives:
  • Select the physical drives you wish to include in your array.
  • Choose the desired RAID level (e.g., RAID 0, RAID 1, RAID 5, RAID 10). The P600 supports various RAID levels for performance and data redundancy.
  • Define the logical drive size and other parameters as needed.
• Managing Arrays: The utility allows you to perform tasks such as:
  • Expanding existing logical drives.
  • Adding spare drives.
  • Monitoring drive status and array health.
  • Performing consistency checks.
• Pemasangan Pemandu: After configuring the arrays, install the appropriate operating system drivers for the HP Smart Array P600 controller. These drivers are typically available on the HP support website or included with your server's driver disc.

4. Penyelenggaraan

Regular maintenance helps ensure the longevity and reliability of your HP Smart Array P600 controller and the data it manages.

• Kemas kini Firmware: Semak secara berkala Sokongan HP webtapak for the latest firmware updates for your P600 controller. Firmware updates can provide performance improvements, bug fixes, and enhanced compatibility.
• Kemas Kini Pemandu: Keep your operating system drivers for the controller up-to-date.
• Battery Backup Unit (BBU) Monitoring: The 3.6V Ni-MH Battery Pack provides cache protection. Monitor its status through the controller utility. If the battery shows signs of degradation or failure, it should be replaced promptly to ensure data integrity during power outages. The part number for the battery is HP Part# 274779-001 or HP Spares# 307132-001.
• Pemeriksaan Fizikal: During server maintenance, visually inspect the controller card for any signs of dust buildup, loose connections, or physical damage. Ensure proper airflow around the card.
• Sandaran Data: While RAID provides data redundancy, it is not a substitute for regular data backups. Always maintain a comprehensive backup strategy for critical data.

5. Penyelesaian masalah

This section provides solutions to common issues you might encounter with your HP Smart Array P600 controller.

6. Spesifikasi

The following are key specifications for the HP Smart Array P600 controller:

• Jenama: Hewlett Packard
• Nombor Model: 337972-B21
• Antara muka perkakasan: PCI-X, SAS
• Dimensi Produk: 18.5 x 7.5 x 3 inci
• Berat Barang: 2 paun
• Peranti Serasi: Desktop (Servers)
• Nombor Stok Kebangsaan: 7025-01-549-2913
• Tarikh Mula-mula Tersedia: 15 Februari 2006
• Pengeluar: Hewlett Packard (Consumables)
• Bahasa: Inggeris
• Bateri tambahan: 3.6V Ni-MH Battery Pack (HP Spares# 307132-001, HP Part# 274779-001)
• Cache Memory: SDRAM 256MB

7. Sokongan dan Jaminan

For technical assistance, driver downloads, firmware updates, and additional product information, please visit the official HP support website. While specific warranty details for this product may vary based on purchase date and region, HP typically provides support resources for its enterprise hardware.

• HP Official Store: For product information and related accessories, visit the HP Store on Amazon.
• General HP Support: For comprehensive support resources, including documentation and troubleshooting guides, please refer to the main HP support portal (search for "HP Support" online).
• Polisi Pemulangan: The buybox winner indicates a 30-day refund/replacement return policy. Please verify with your seller for specific return terms.