ANEX IQ Basic Stroller
IQ ALL-IN-ONE
Lipatan bingkai
KERANGKA IQ
Pembukaan bingkai
Memasang roda hadapan
Mengunci roda pusing hadapan
Memasang roda belakang
Brek
Penyerapan kejutan
Mengendalikan peraturan
Memutuskan/menyambung bakul beli-belah
Membawa pemegang
Pelarasan lebar bingkai
Membongkar beg pengangkut
Lipatan kot
Pembukaan tempat tidur bayi
Lampiran pada bingkai
Pengudaraan
Pelarasan tudung Carrycot
Lampiran penutup Carrycot
Pembersihan Carrycot
Lampiran pada bingkai
UNIT SEAT IQ
Lipatan bingkai dengan tempat duduk
Pelarasan hud unit tempat duduk
Pelarasan sandaran unit tempat duduk
Pengudaraan sandaran unit tempat duduk
Pelarasan tapak kaki
Penghalang keselamatan unit tempat duduk
Gancu tali pinggang keselamatan
Pelarasan tali pinggang keselamatan
Pembersihan unit tempat duduk
Perhimpunan barangan lembut
Pelarasan tudung Buggy
Pengudaraan sandaran kereta buggy
Pelarasan sandaran Buggy 
Pelarasan tapak kaki
Gancu tali pinggang keselamatan
Pelarasan tali pinggang keselamatan
Lipatan bingkai dengan buggy
Sarung hujan untuk katil bawa/ unit tempat duduk
Semak manual terkini pada kami webtapak: anexbaby.com
Maklumat Tertakluk kepada perubahan tanpa notis. Anex tidak akan bertanggungjawab untuk kesilapan teknikal atau ketinggalan yang terkandung dalam manual ini. Produk yang dibeli mungkin berbeza daripada produk seperti yang diterangkan dalam manual ini.
AVALEX PTE. LTD.,
8 Jalan Eu Tong Sen #17-88, Tengah
Menara pejabat 2, Singapura, 059818
+65 62215096
office@anexbaby.com
Dokumen / Sumber
 | IQ Basic Stroller |
Rujukan
- Manual Penggunamanual.tools
Dear Anex Team,
We are experiencing an issue with our Anex IQ stroller and would appreciate your assistance.
We have these height adapters that were previously attached to the frame, and we used them with the bassinet without any problems. After removing the bassinet, we installed the seat unit (stroller seat) without the adapters.
However, the height adapters are now stuck in the seat unit, and we are unable to remove them. We have tried pulling them out, but they do not come off.
Could you please advise how to safely remove these adapters? If possible, we would appreciate it if you could send us instructions or a guide.
We have attached photos for your reference.
Thank you in advance for your help.
salam hormat,
Yuliya Tolkishevskaya
We are experiencing an issue with our Anex IQ stroller and would appreciate your assistance.
We have these height adapters that were previously attached to the frame, and we used them with the bassinet without any problems. After removing the bassinet, we installed the seat unit (stroller seat) without the adapters.
However, the height adapters are now stuck in the seat unit, and we are unable to remove them. We have tried pulling them out, but they do not come off.
Could you please advise how to safely remove these adapters? If possible, we would appreciate it if you could send us instructions or a guide.
We have attached photos for your reference.
Thank you in advance for your help.
salam hormat,
Yuliya Tolkishevskaya
How do I remove the height adapters from the Anex IQ seat unit if they are stuck?
Removing height adapters from the Anex IQ seat unit typically requires engaging the release mechanism located on the adapters themselves or the seat unit's attachment points. If they are stuck, please try the following steps:
Awas: Do not use excessive force or tools like pliers, as this may damage the plastic locking tabs. If the adapters remain stuck, it is recommended to contact Anex customer support directly at office@anexbaby.com or visit an authorized service center, as there may be a mechanical obstruction or a need for professional lubrication of the locking pins.
Read the full Q&A page