XOSS G3/G3+ GPS Bike Computer User Manual

pengenalan

The XOSS G3 and G3+ are advanced GPS bike computers designed for road and MTB cycling training. They provide comprehensive data tracking, GPS positioning, and connectivity with external sensors and a dedicated mobile application. This manual will guide you through the installation, operation, and maintenance of your device.

Ciri-ciri utama termasuk:

• Paparan HD 2.8 inci
• Penarafan kalis air IP67 untuk kegunaan semua cuaca
• Ultra-lightweight design: G3 weighs 57g, G3+ weighs 58.5g
• Hayat bateri sehingga 40 jam
• Antara muka pengecasan jenis-C
• Supports app connectivity for data synchronization and analysis
• Real-time gradient display for precise navigation
• Customizable watch faces and buttons (G3+ only)
• G3+ supports ANT+ for compatibility with various external sensors

Kandungan Pakej

Sila tandai kotak untuk item berikut:

Image: XOSS G Product Accessories Display

• XOSS G+ Bicycle Computer x 1
• Cycling Computer Mount x 1
• Kabel USB Jenis-C x 1
• Protection Rubber Pad x 1
• Gelang Getah x 2
• Manual Pengguna x 1

Persediaan

Pemasangan Peranti

1. Letakkan pad getah di belakang tempat duduk basikal.
2. Gunakan gelang getah untuk mengikat pendakap ke bar hendal atau batang.
3. Jajarkan tab di bahagian belakang peranti dengan alur pada dirian basikal, tekan sedikit ke bawah dan putar peranti 90 darjah sehingga ia terkunci pada tempatnya.

Image: Bike Computer Installation Diagram

Arahan Operasi

Kedudukan GPS

1. Tekan lama butang kanan untuk menghidupkan peranti.
2. Short press the left button to start searching for GPS. The GPS icon will appear and start to flash.
3. After startup, stay still for a few minutes to acquire a GPS signal. When the GPS icon stops flashing with a BEEP prompt, it indicates the device is ready.
4. Long press the left button to save the workout after ending the ride. The Bike Computer will then restore to its initial interface.

Nota: When searching for a GPS signal, please remain static and make sure your device is used in an open, barrier-free area. The device only supports outdoor recording.

Image: XOSS G3+ Display with GPS and Battery Indicators

Berhubung dengan XOSS APP

The XOSS app allows for data synchronization and device settings management.

1. Cari untuk "XOSS" in Google Play/App Store, or scan the QR code below to download the XOSS APP.
2. Turn on your XOSS G+ device and ensure Bluetooth is enabled on your phone.
3. Open the XOSS APP, then navigate to Devices > Bike Computers > G/G+.

After connecting your XOSS G+ to the XOSS APP, you can click on settings to change Backlight, Key Tone, Auto Pause, Speed Alert, Tire Circumference, Units, Time Zone, etc. Your workout data will be automatically synced to the XOSS APP.

Nota: Tekan lama butang kiri untuk menamatkan rakaman sebelum sambungan. Aplikasi ini direka bentuk untuk Bluetooth 4.0 atau versi yang lebih baharu.

Image: XOSS App Interface and QR Codes

Manage Workouts via XOSS APP

1. Connect your G+ device to the XOSS APP.
2. klik pada Storage > Workout.
3. klik Sunting in the upper right corner to select and manage (delete or resync) your workouts.

Image: XOSS App Workout Management Screen

Reka Letak Data Tersuai

Customize the data displayed on your device screen through the XOSS APP:

1. Sambungkan G+ ke APLIKASI XOSS.
2. klik Data Layout.

Keperluan: Firmware version 1.09 or later; XOSS app version Android 3.10.2 or later, iOS 3.11.0 or later.

Tetapan Zon Waktu dalam APLIKASI XOSS

To synchronize the device's time zone with your phone:

1. Sambungkan G+ ke APLIKASI XOSS.
2. klik Tetapan> Pro Penggunafile > Time Zone.

Recordable Data Types

The device can record up to 50 types of data, including but not limited to:

• Speed (Current, Avg, Max, Lap Avg, Lap Max)
• Heart Rate (Current, Avg, Max, Lap Avg, Lap Max)
• Power (Current, Avg, 3S Avg, 10S Avg, 30S Avg, Max, Lap Avg, Lap Max, W/KG)
• Cadence (Current, Avg, Max, Lap Avg, Lap Max)
• Time (Current, Paused, Total, Lap, Lap Paused, Lap Total)
• Distance (Current, Lap, Odometer)
• Elevation (Current, Gain, Grad, Loss, Max, VAM, Lap Gain, Lap Loss, Lap Max, Lap VAM)
• Calories, Lap Calories, Clock, Temperature, Laps
• Headlight Control, Taillight Control

ANT+ Sensor Connection (G3+ only)

The G3+ supports connection with various ANT+ sensors.

1. Bring the device within 3 meters of your sensors and keep it at least 10 meters away from other riders' sensors.
2. Press both buttons simultaneously on the XOSS G+ until the ANT+ icon starts flashing, indicating it's searching for active sensors.
3. If pairing succeeds, the icon will remain static. Press the right button again to enter the "Tire Circumference" setting interface.

Image: ANT+ Sensor Connection Process

Device Settings (Circumference, Metric/Imperial, Time Zone)

These settings can be adjusted directly on the device:

• Tire Circumference Setting (mm): Use the left button to set numbers, the right button to switch position, and long press the right button to proceed to the next step.
• Metric/Imperial Unit Setting: Use the left button to switch units, and long press the right button to proceed to the next step.
• Tetapan Zon Waktu: Use the left button to switch numbers, the right button to switch position, and long press the right button to end the setting.

Customizable Function Button (G3+ only)

The middle button on the G3+ cycling computer is customizable. It can be configured via the XOSS app to:

• Start lap counting.
• Control headlight and taillight switches.
• Toggle between different light modes.

Lap Counting (G3+ only)

The G3+ supports four types of lap counting:

• Berasaskan Masa: Automatically counts a lap when a set time interval is reached.
• Distance-Based: Automatically counts a lap when a set distance is reached.
• Location-Based: Tekan butang tengah untuk menandakan lokasi. Komputer akan mengira pusingan secara automatik setiap kali ia sampai ke lokasi yang ditanda.
• Manual: Press the middle button once to complete a lap and start the next.

*All four lap counting modes require successful GPS positioning to start. Long press the left button to end laps.

Penyelenggaraan

Peningkatan Perisian Tegar

When new firmware is available, the XOSS APP will prompt you to update it. It is recommended to keep the firmware updated for optimal performance and new features.

• If you encounter issues (e.g., stuck in dFu mode) during a firmware upgrade, try toggling Bluetooth off and back on in your phone's settings, then reconnect the XOSS APP to attempt the upgrade again.

Menyelesaikan masalah

• Isu Pemerolehan Isyarat GPS: Ensure you are in an open, barrier-free area and remain static during initial GPS search.
• Masalah Sambungan Apl: Verify Bluetooth is enabled on both the device and your phone. Ensure the XOSS app is updated to the latest version (Bluetooth 4.0 or later required).
• Kegagalan Kemas Kini Perisian Tegar: If the device gets stuck during an update, try restarting Bluetooth on your phone and reconnecting to the app.
• Sensor Connectivity (G3+): Ensure ANT+ sensors are within 3 meters of the device and not interfered with by other nearby sensors.

Spesifikasi

Below are the detailed specifications for the XOSS G3 and G3+ models:

Image: Product Parameters Comparison (G vs G+)

Waranti dan Sokongan

Perkhidmatan & Waranti selepas jualan

The device comes with a one-year free warranty from the date of purchase. Please contact your original dealer for warranty service.

Syarat berikut tidak dilindungi oleh jaminan:

1. Normal aging loss of the battery.
2. Kerosakan dan kehilangan produk akibat pemasangan yang tidak betul.
3. Kerosakan yang disebabkan oleh penggunaan yang tidak normal, seperti suhu tinggi dan kerosakan air.
4. Damage caused by dismantling the device yourself or by unauthorized maintenance personnel.

Sokongan

For more product information and support, please access the official XOSS webtapak:

• https://www.xoss.co
• https://help.xoss.co

You can also refer to the original user manual PDF for additional details: Manual Pengguna (PDF)