1. Pengenalan
This manual provides instructions for the Arvin QCC5181/QCC3084 Bluetooth 5.4 Receive Amplifier Decoding Board. This versatile board functions as a high-fidelity audio receiver and digital-to-analog converter, supporting advanced Bluetooth codecs and offering multiple input/output options for integration into various audio systems.
Figure 1: Arvin QCC5181/QCC3084 Bluetooth 5.4 Receive Amplifier Decoding Board
2. Spesifikasi
| Ciri | Perincian |
|---|---|
| Versi Bluetooth | 5.4 (backward compatible with 5.3/5.1/4.2) |
| Kodek Bluetooth Disokong | SBC, AAC, aptX, aptX LL, aptX HD, LDAC, aptX Adaptive, LHDC (QCC5181 supports LDAC) |
| Bluetooth Max SampKadar ling | 24-bit/192kHz (LDAC) |
| USB Max SampKadar ling | 24-bit / 96kHz |
| Keluaran | IIS (I2S), SPDIF (Coaxial) - simultaneous output with custom firmware |
| Input | Bluetooth, USB Audio, CD IIS, SPDIF In |
| Input Kuasa | DC 5-20V (no distinction between positive and negative) |
| Dimensi (WxHxD) | 57.1mm x 32.7mm (lebih kurang 2.25" x 1.29") |
| Berat badan | 50g |
| Peralatan yang serasi | Amplifiers, Digital-to-Analog Converters (DACs) |
Figure 2: Board dimensions (57.1mm x 32.7mm)
3. Persediaan dan Sambungan
Carefully follow the instructions below for proper installation and connection of the decoding board. Ensure all power is disconnected before making any connections.
3.1 Pengenalan Komponen
Figure 3: Board Component Layout
- M3 screw holes
- Remote control reception (optional)
- Antena Bluetooth
- Bluetooth module (QCC5125/QCC5171 - Note: Product uses QCC3084/QCC5181)
- Key control line (up and down, play, pause)
- Input kad bunyi USB
- IIS Input
- Output IIS
- Keluaran sepaksi
- Input sepaksi
- Bluetooth connection light (flashing when not connected, always on when connected)
- Power supply 5-12V (no distinction between positive and negative)
3.2 Gambarajah Pendawaian
Refer to the detailed wiring diagram for all electrical connections. Pay close attention to polarity where indicated, although the main power input is non-polar.
Figure 4: Detailed Wiring Diagram
- Input Kuasa (DC IN): Connect 5-20V DC power. The board supports non-polarized input.
- Bluetooth Antenna (BT ANT 2.4G): Connect the included 2.4G Bluetooth antenna for optimal signal reception.
- Key Control (KEY VOL-, KEY VOL+, KEY PLAY): Connect external buttons for volume control and playback functions.
- Audio USB: Connect to a computer via USB for audio decoding.
- IIS Output (MCK OUT, BCK OUT, LRCK OUT, DATA OUT, GND): Standard 4-wire IIS output. If your decoding chip does not require MCK, it can be left unconnected.
- SPDIF Output (SPDIF OUT, GND): Connect to a coaxial digital input on your amppenguat atau DAC.
- SPDIF Input (SPDIF IN, GND): Connect external coaxial digital audio sources.
- Indicator Light (LED+, LED-): Connect an external LED for status indication.
Important Note on Input Switching:
The board supports switching between coaxial and IIS inputs using jump caps. However, any change to the jump cap configuration requires the board to be re-powered for the new setting to take effect.
4. Operasi
4.1 Sambungan Bluetooth
- Ensure the board is powered on. The Bluetooth connection light (11 in Figure 3) will flash, indicating it is ready for pairing.
- On your source device (smartphone, tablet, etc.), search for Bluetooth devices. The Bluetooth name will be "QCC3084" or "QCC5181".
- Select the appropriate Bluetooth name to pair. Once successfully connected, the Bluetooth connection light will remain steadily on.
4.2 Input Priority and Automatic Switching
The board prioritizes Bluetooth input. If a Bluetooth connection is active, it will play audio from the Bluetooth source.
- If Bluetooth is not connected, the board can decode audio from the computer's USB input.
- If the Bluetooth connection is disconnected, the board will automatically switch to other available inputs, such as the sound card IIS or coaxial input.
4.3 Key Control
If external key control lines are connected (5 in Figure 3), you can use them to:
- Adjust volume (KEY VOL+, KEY VOL-)
- Control playback (KEY PLAY for play/pause)
5. Penyelenggaraan
To ensure the longevity and optimal performance of your decoding board, follow these maintenance guidelines:
- Keringkan: Avoid exposing the board to moisture or liquids.
- Bersihkan Perlahan-lahan: Use a soft, dry cloth to clean the board. Do not use harsh chemicals or abrasive materials.
- Kendalikan dengan Berhati-hati: Electronic components are sensitive. Avoid dropping the board or subjecting it to physical shock.
- Elektrik Statik: When handling the board, especially during installation, take precautions against static discharge (e.g., use an anti-static wrist strap).
- Pengudaraan: Ensure adequate airflow around the board if enclosed in a case to prevent overheating.
6. Penyelesaian masalah
| Masalah | Kemungkinan Punca | Penyelesaian |
|---|---|---|
| No power/Board not turning on | Bekalan kuasa tidak betul voltage or connection. | Verify power input is within 5-20V DC. Check power cable connections. |
| Bluetooth not pairing/connecting | Bluetooth antenna not connected; board not in pairing mode; interference; already connected to another device. | Ensure Bluetooth antenna is securely connected. Check if the LED is flashing (pairing mode). Disconnect from other devices. Reduce distance to source. |
| Tiada output audio | Incorrect output connection (IIS/SPDIF); wrong input selected; volume too low; connected device issues. | Check IIS/SPDIF wiring to your amplifier/DAC. Ensure the correct input is active (Bluetooth priority). Increase volume on source and receiving device. Test with different audio sources. |
| Input switching not working | Jump caps changed without re-powering. | After adjusting jump caps for coaxial/IIS input selection, power cycle the board. |
| Keluaran SPDIF voltagtahap e | Uncertainty about signal specifications. | The SPDIF output adheres to standard digital audio specifications, typically 0.5Vp-p into a 75-ohm impedance. Ensure your receiving device is compatible with this standard. |
7. Petua Pengguna
- For the best audio quality, especially with high-resolution codecs like LDAC, ensure your source device also supports these codecs.
- When using the USB audio input, ensure your computer's audio settings are configured to output to the decoding board.
- Experiment with different power supplies within the 5-20V range to find the one that provides the most stable performance for your setup.
- If experiencing intermittent Bluetooth connection, try relocating the antenna or the board to a less obstructed area.
8. Waranti dan Sokongan
For warranty information, technical support, or any inquiries regarding your Arvin QCC5181/QCC3084 Bluetooth Decoding Board, please contact the seller directly. Keep your purchase records for reference.
Penjual: BEAYEAU Store