Manual Arahan

1. Pengenalan

This manual provides detailed instructions for the installation, setup, and operation of your Scimagic-RC Tuya WiFi 433MHZ Receiver, 1527 Remote Control, and Wireless Numeric Keypad. This system is designed to provide secure and convenient access control for automatic garage doors, swing gates, and sliding gate openers, integrating with smart home platforms like Tuya, Smart Life, Google Assistant, and Amazon Alexa.

2. Maklumat Keselamatan

• Ensure all power is disconnected before performing any wiring or installation procedures.
• Installation should be performed by qualified personnel if you are unsure about electrical connections.
• Jauhkan peranti daripada air dan suhu yang melampau.
• Do not attempt to repair the device yourself; contact support for assistance.
• This device is intended for use with automatic door/gate systems only.

3. Kandungan Pakej

Bergantung pada pembelian anda, pakej anda mungkin termasuk:

• Pad Kekunci Berangka Tanpa Wayar
• 433MHZ Receiver
• 433MHZ Remote Control (may be sold separately or in combinations)
• Perkakasan pemasangan (skru, sauh dinding)

4. Spesifikasi

4.1. Wireless Numeric Keypad

kuasa	6V DC (2x CR2032 Li battery)
Hayat Bateri	Approx. 2 years (based on 4 operations/day)
Kekerapan	433.92MHz +/- 75KHz
Kuasa Pemancar	1mW
Format Data	Standard
Suhu Operasi	-20°C hingga +55°C
Password Number	0-8 digit
Tahap Kalis Air	IP54
Dimensi	85 x 75 x 35 mm
Berat badan	150g

4.2. 433MHZ Receiver

Bekalan Kuasa	12V-24V DC
Kekerapan	433.92Mhz
Kod	Fixed/Learning/Rolling codes compatible
Saluran	2 Saluran
Suhu Operasi	-40°C hingga +80°C
Julat Penerimaan	10-50m (Built-in Aerial antenna)

4.3. 433MHZ Remote Control

bahan	Plastik + Logam
Kekerapan Operasi	433.92MHz
Penggunaan	For 433Mhz RF receiver 1527 decode
Keserasian	Supports learning code (1527) receivers only. Not a clone remote.

5. Persediaan

5.1. Keypad Battery Installation

The keypad requires two CR2032 Li batteries. To install or replace them:

1. Locate the battery compartment on the rear of the keypad.
2. Open the battery rear cover.
3. Masukkan dua bateri CR2032, pastikan kekutuban yang betul.
4. Close the battery rear cover securely.

5.2. Pendawaian Penerima

Connect the receiver to your automatic door/gate opener system according to the following terminal definitions:

• SEMUT: penerima Antenna
• CH1: Output Geganti 1
• CH2: Output Geganti 2
• V+: Voltage + (12V-24V DC power supply)
• GND: tanah

5.3. Pairing Remote Control with Receiver

To program a new remote control to operate your garage door or gate:

1. Press and release the yellow round button on the opener (or the 'LEARN' button on the receiver board). The learn indicator light (blue LED) will glow steadily for approximately 30 seconds.
2. Within these 30 seconds, press and hold the desired button on the hand-held remote that you wish to use to operate your garage door/gate.
3. Release the button on the remote when the opener light blinks once, or the blue LED on the receiver goes out. The new remote is now programmed.

5.4. Pairing Keypad with Receiver

To program the wireless numeric keypad with the receiver:

1. Long press the 'LEARN' button on the receiver board until the blue LED lights up.
2. On the keypad, enter the original password (e.g., '11' for left channel or '22' for right channel, as indicated in the video demonstration).
3. The blue LED on the receiver will go out, indicating a successful match.

Note: Refer to the video demonstration for a visual guide on the pairing process.

6. Arahan Operasi

6.1. Menggunakan Alat Kawalan Jauh

Once paired, press the programmed button on your remote control to activate the connected garage door or gate opener.

6.2. Using the Wireless Numeric Keypad

To operate the connected device using the keypad:

1. Enter your programmed password on the keypad.
2. Press the appropriate channel button (e.g., 'left arrow' or 'right arrow' depending on the channel programmed) to activate the opener.

The keypad is a dual-channel transmitter, meaning it can control two separate devices or functions with different combinations.

7. Penyelenggaraan

7.1. Keypad Battery Replacement

If the keypad's performance degrades or it stops responding, the CR2032 batteries may need replacement. Follow the steps in Section 5.1 for battery installation.

7.2. Pembersihan

Lap peranti dengan kain lembut dan kering. Jangan gunakan pembersih atau pelarut yang melelas.

8. Penyelesaian masalah

• Peranti tidak bertindak balas: Check battery levels in the keypad/remote. Ensure the receiver is powered correctly. Re-attempt the pairing process.
• Julat terhad: Ensure the receiver's antenna is unobstructed. Check for sources of interference (e.g., other wireless devices, metal structures).
• Kegagalan berpasangan: Ensure you are following the pairing steps precisely. The timing for pressing buttons during the learning phase is crucial.

9. Petua Pengguna

• For optimal performance, ensure the keypad is mounted in a location with good line-of-sight to the receiver, especially for outdoor installations.
• The keypad is suitable for 95% of garage door openers worldwide.
• The keypad's estimated transmission range is 200m in open space and 35m indoors.
• The system is compatible with various smart home platforms, including Tuya, Smart Life, Google Assistant, and Amazon Alexa, allowing for integrated control.
• The keypad is designed for utmost security, with transmitted codes changing at each session.
• This system is compatible with Nice OXI poa1 portals.

10. Waranti dan Sokongan

All products come with a 1-year warranty from the store. For technical support or warranty claims, please contact the seller directly. Ensure you retain your purchase receipt as proof of purchase.

For additional information, you may refer to the Manual Pengguna (PDF).

11. Pensijilan

This product is certified with:

• CE
• RoHS