1. Pengenalan
This manual provides essential information for the installation, maintenance, and troubleshooting of your new replacement drive belt for Midea bread machines. Please read these instructions carefully before attempting any installation or repair to ensure safe and correct operation.
2. Maklumat Keselamatan
- Always unplug the bread machine from the power outlet before attempting any inspection, maintenance, or replacement of parts.
- Wear appropriate safety gear, such as gloves, if necessary.
- Jauhkan bahagian kecil daripada kanak-kanak.
- If you are unsure about any step, consult a qualified technician or refer to your bread machine's original service manual.
3. Produk Lebihview
This is a replacement drive belt designed for various Midea bread machine models. The drive belt is a critical component that transfers power from the motor to the kneading paddle, ensuring proper mixing and kneading of dough.
Figure 1: Bread machine drive belt with '175T' marking, indicating 175 teeth.
Rajah 2: Sisi view of the bread machine drive belt.
4. Pemasangan (Penggantian)
Replacing the drive belt requires disassembling parts of your bread machine. Refer to your specific bread machine model's service manual for detailed disassembly instructions. The general steps are as follows:
- Unplug the Bread Machine: Ensure the appliance is completely disconnected from the power supply.
- Akses Mekanisme Pemacu: Carefully disassemble the bottom or rear casing of your bread machine to expose the motor and drive belt assembly. This usually involves removing screws.
- Tanggalkan Tali Pinggang Lama: Once the drive mechanism is accessible, gently remove the old, worn, or broken belt from the motor pulley and the paddle shaft pulley. You may need to carefully pry it off.
- Pasang Tali Pinggang Baharu: Place the new belt (Model AE-HCDM167) onto the smaller motor pulley first. Then, stretch it over the larger paddle shaft pulley. Ensure the belt is seated correctly in the grooves of both pulleys. It should be snug but not excessively tight.
- Putaran Ujian: Manually rotate the paddle shaft to ensure the belt moves smoothly and without obstruction.
- Pasang semula: Carefully reassemble the bread machine casing, memastikan semua skru diketatkan dan tiada wayar yang tersepit.
- Ujian Permulaan: Plug in the bread machine and run a short cycle (e.g., dough cycle) to confirm the new belt is functioning correctly.
5. Arahan Operasi
This drive belt is a component part of your bread machine. Once correctly installed, the operation of your bread machine will resume as per its original manufacturer's instructions. There are no specific operating instructions for the belt itself.
6. Penyelenggaraan
To prolong the life of your bread machine drive belt:
- Pemeriksaan Berkala: Periodically inspect the belt for signs of wear, cracking, fraying, or stretching. This can be done during routine cleaning or if you notice changes in the bread machine's operation.
- Jaga kebersihan: Ensure the area around the belt and pulleys is free from dough residue, flour, or other debris that could cause friction or damage.
- Elakkan beban berlebihan: Do not overload your bread machine with ingredients beyond its recommended capacity, as this can put excessive strain on the drive belt.
7. Penyelesaian masalah
If your bread machine is not functioning correctly after belt replacement, consider the following:
| simptom | Kemungkinan Punca | Penyelesaian |
|---|---|---|
| Kneading paddle not turning or turning slowly | Belt not properly seated on pulleys; Belt too loose; Motor issue (less likely if new belt) | Unplug, re-open, and ensure belt is correctly positioned and tensioned. If belt is correct, consult bread machine manual for motor diagnostics. |
| Grinding or squealing noise during operation | Belt rubbing against casing; Pulleys misaligned; Debris in mechanism | Unplug, re-open, check for obstructions. Ensure pulleys are aligned and belt is not rubbing. Clean any debris. |
| Bau terbakar | Belt friction; Motor overheating | Immediately unplug the machine. Check for belt rubbing or excessive tension. If smell persists, discontinue use and seek professional repair. |
8. Spesifikasi
| Atribut | Nilai |
|---|---|
| Nombor Model | AE-HCDM167 |
| taip | Bahagian Pembuat Roti |
| Panjang | 525mm |
| Lebar | 8mm |
| Bilangan Gigi | 175T |
| Compatible Midea Models | AHS15AB-PW, AHS20AB-PR, AHS15AC-PRS, AHS15AC-PGS, EHS15AP-PW, AHS20AC-PASY, AHS15AC-PAS, EHS15AP-PR, THS15BB-PW, EHS15AP-PY, AHS15AC-PRSY, AHS15AC-PY, AHS20AB-PT, EHS15AP-PG, THS20BB-PASY, EHS15AP-PWSY, EHS15AP-PGS, AHS20AB-PP, THS15BB-PARY, THS15BB-PGRY, EHS15Q3-PWRY, EHS15Q3-PRRY, EHS20Q3-PWRY, 260010600013, AHS20AB-PG, EHS15AP-PG, EHS15AP-PR |
9. Petua Pengguna
- Sahkan Keserasian: Sebelum pembelianasing, always double-check the model number and specifications (length, width, teeth count) of your old belt against this replacement part to ensure perfect fit.
- Pengendalian Lembut: When installing, avoid twisting or sharply bending the new belt, as this can damage its internal structure and reduce its lifespan.
- Kebersihan adalah Kunci: Ensure the pulleys are clean and free of grease or debris before installing the new belt to prevent premature wear.
10. Waranti dan Sokongan
This replacement part is typically covered by the seller's or manufacturer's warranty for a limited period against manufacturing defects. Please retain your proof of purchase for any warranty claims. For specific warranty details or technical support, please contact the retailer or the part manufacturer directly.
