Manual Arahan Pengawal Meter Sensor Suhu Digital Dwi LED W1088

1. Pengenalan

The YIDI W1088 Dual LED Digital Temperature Sensor Meter Controller is a versatile device designed for precise temperature regulation in various applications. It features independent dual-way control for heating or cooling, a clear red and blue dual LED display, and supports high/low temperature alarms. This manual provides detailed instructions for its setup, operation, and maintenance.

Figure 1: W1088 Dual LED Digital Temperature Controller

2. Ciri-ciri

• Heating or cooling control capability.
• Red and blue dual LED display for clear temperature readings.
• Independent dual-way temperature controller for two separate outputs.
• Temperature display resolution of 0.1°C.
• Direct power output.
• Supports high and low temperature alarms.
• Retains parameters after power loss.
• Suitable for home temperature control, farms, cold storage, greenhouses, aquariums, and incubators.

3. Spesifikasi

Figure 2: W1088 Temperature Controller Dimensions (72x56x31mm)

4. Persediaan

4.1. Membongkar dan Komponen

Sebelum pemasangan, pastikan semua komponen ada:

• 1 x W1088 Temperature Controller
• 2 x Waterproof NTC 10K Sensors (1m length each)

4.2. Produk Lebihview

Figure 3: W1088 Controller Front Panel Layout

1. NO.1 Work Signal Indicator
2. NO.1 Measured Temperature Display
3. NO.1 Start Temperature Set Button (Up)
4. NO.1 Stop Temperature Set Button (Down)
5. NO.2 Work Signal Indicator
6. NO.2 Measured Temperature Display
7. NO.2 Stop Temperature Set Button (Down)
8. NO.2 Start Temperature Set Button (Up)
9. Model Number (XK-W1088)

4.3. Arahan Pendawaian

Important Safety Note: Ensure the power supply is disconnected before performing any wiring to prevent electric shock or damage to the device.

The W1088 controller features direct output, meaning the output voltage is synchronized with the input voltage. When the controller is actively working (indicator light is on), the output voltage akan sama dengan vol inputtage. When the controller is off (indicator light is off), there will be no voltage pada output.

DC Power Supply Wiring (12VDC / 24VDC)

Figure 4: DC Wiring Diagram for W1088 (12V/24V DC)

• Connect the 12V/24V DC power supply to the central input terminals (positive and negative).
• Connect the detection probes (sensors) to their respective sensor input terminals.
• Connect your DC 12V/24V heating or cooling devices to the 'Direct Output DC12V/24V' terminals for OUT1 and OUT2. Ensure correct polarity.

AC Power Supply Wiring (110-220VAC)

Figure 5: AC Wiring Diagram for W1088 (220V AC)

• Connect the 110-220VAC power supply to the central input terminals (Live 'L' and Neutral 'N').
• Connect the detection probes (sensors) to their respective sensor input terminals.
• Connect your AC 220V heating or cooling devices to the 'Direct Output AC220V' terminals for OUT1 and OUT2.

5. Operasi

5.1. Setting the Starting Temperature

1. Tekan ke UP button (③ for OUT1, ⑧ for OUT2) once to display the current starting temperature.
2. Tekan lama UP button for approximately 3 seconds until the display flashes.
3. Gunakan UP dan TURUN buttons to adjust the desired starting temperature.
4. The setting will automatically save after a few seconds of inactivity.

5.2. Setting the Stopping Temperature

1. Tekan ke TURUN button (④ for OUT1, ⑦ for OUT2) once to display the current stopping temperature.
2. Tekan lama TURUN button for approximately 3 seconds until the display flashes.
3. Gunakan UP dan TURUN buttons to adjust the desired stopping temperature.
4. The setting will automatically save after a few seconds of inactivity.

5.3. Heating and Cooling Modes

The controller automatically determines the working mode based on the relationship between the start and stop temperatures:

• Mod Pemanasan: When the Start Temperature is kurang daripada the Stop Temperature (e.g., Start 20°C, Stop 25°C). The output will activate when the temperature drops below the start temperature and deactivate when it reaches the stop temperature.
• Mod Penyejukan: When the Start Temperature is lebih besar daripada the Stop Temperature (e.g., Start 30°C, Stop 25°C). The output will activate when the temperature rises above the start temperature and deactivate when it drops to the stop temperature.

6. Tetapan Menu Lanjutan

To enter the advanced setting mode, press and hold the UP ① dan UP ② butang serentak selama 3 saat.

guna UP ② dan DOWN ② buttons to adjust values within the menu. Press UP ① to cycle through the parameters (P0, P1, P2, P3). The controller will automatically exit the setting mode after a few seconds of inactivity.

6.1. Temperature Correction

To correct temperature readings:

1. For OUT1, press and hold UP ① dan DOWN ① buttons simultaneously for 3 seconds. The display will show "0.0".
2. Gunakan UP ① dan DOWN ① buttons to set the correction value.
3. The corrected value will be added to the measured temperature (Positive Value = Measured Value + Corrected Value).
4. For OUT2, use the same method by pressing and holding UP ② dan DOWN ② butang.

6.2. Reset Factory Settings

To reset the controller to its factory default settings:

1. With the power on, press and hold the DOWN ① dan DOWN ② butang serentak selama 3 saat.
2. The display will show "888", and then the controller will automatically return to displaying the detected temperature.

7. Penyelesaian masalah

• Tiada Paparan/Kuasa: Check power connections and ensure the correct voltage (110-220VAC, 12VDC, or 24VDC) is supplied to the controller.
• Bacaan Suhu yang salah: Verify that the NTC 10K sensors are properly connected and submerged in the medium being measured. Consider performing a temperature correction if a consistent offset is observed.
• Output Tidak Diaktifkan: Ensure the start and stop temperatures are set correctly for either heating or cooling mode. Check the wiring to the heating/cooling device. Remember that the output is direct, so the connected device must match the controller's input voltage.
• Penggera Tidak Berfungsi: Check the P2 (High Temp Alarm) and P3 (Low Temp Alarm) settings in the advanced menu to ensure they are configured within the desired range.
• Pengawal Tidak Menjawab: Try resetting to factory settings (see section 6.2). If the issue persists, disconnect power for a few minutes and then reconnect.

8. Petua Pengguna

• The W1088 is highly suitable for applications like incubators, allowing precise temperature control (e.g., setting to 37.5°C).
• Both independent output channels (OUT1 and OUT2) can be configured for heating or cooling, providing flexibility for managing two separate temperature zones or two different devices within one zone.
• This device is a temperature controller and does not include timer functions for actions like egg turning. For such functions, an additional timer device would be required.

9. Waranti dan Sokongan

For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the seller or manufacturer directly. Keep your purchase records for reference.