1. Pengenalan
This manual provides detailed instructions for the safe and effective use of your Godox K-180A 180Ws Photography Studio Flash Strobe Light Kit. Please read this manual thoroughly before operating the equipment and keep it for future reference.
2. Maklumat Keselamatan
Always observe basic safety precautions when using electrical equipment to reduce the risk of fire, electric shock, or injury.
- Jangan dedahkan unit kepada hujan atau lembapan.
- Do not disassemble the unit. If repairs are needed, contact qualified service personnel.
- Pastikan vol dayatage matches the unit's requirements (AC220/60Hz or 110V/60Hz).
- Jauhkan daripada kanak-kanak.
- Unplug the unit from the power source before cleaning or when not in use.
- Avoid prolonged continuous use of the modeling lamp; allow it to cool down for at least 1 minute after 5 minutes of continuous use to prevent overheating.
3. Kandungan Pakej
Verify that all items are included in your package (based on Kit 8, the most comprehensive option):
- 1x Godox K-180A Flash Unit
- 1x RT-16 Trigger (Transmitter and Receiver)
- 1x 180cm Light Stand
- 1x FS50X70cm Grid Softbox
- 1x Modeling Lamp
- Kabel Kuasa 1x
4. Arahan Persediaan
4.1. Light Stand Assembly
Unfold the light stand legs and extend the telescopic sections to the desired height. Ensure all locking knobs are securely tightened.
4.2. Flash Unit Preparation
- Mount the K-180A flash unit onto the top stud of the light stand.
- Adjust the mounting bracket to achieve the desired angle and securely tighten it.
- The umbrella input is available for attaching a studio umbrella if desired.
4.3. Softbox Assembly
Assemble the FS50X70cm Grid Softbox according to its specific instructions. Attach it to the universal mount on the flash unit.
4.4. RT-16 Trigger Setup
Insert the 23A 12V battery into the transmitter and 2 AAA batteries into the receiver (AAA batteries for receiver not included). Connect the receiver to the flash unit's sync port.
4.5. Sambungan Kuasa
Connect the power cord to the flash unit's power socket and then to a suitable AC power outlet. Ensure the power switch is in the OFF position before connecting.
5. Arahan Operasi
5.1. Hidupkan/Mati Kuasa
Flip the Power Switch (labeled 'POWER') to turn the flash unit ON or OFF. The Charging LED Indicator will illuminate during charging.
5.2. Pemodelan Lamp Kawalan
Use the Modeling Light Switch (labeled 'MODEL') to turn the modeling lamp ON or OFF. Pushing it downwards (G position) turns it off, upwards (F position) turns it on. Note: Do not keep the modeling lamp on for too long; it is recommended to cool it down for 1 minute after 5 minutes of continuous use.
5.3. Flash Output Control
Rotate the Flash Output Controller (labeled with '+' and '-') to adjust the flash power. The output is stepless from 1/8 to full power. This allows for precise light requirements in different environments.
5.4. Butang Ujian
To test the flash or before taking a picture, push the Test Button (labeled 'TEST'). This can also be used to adjust the brightness when combined with the flash output controller.
5.5. Slave Trigger Mode
The flash unit can be triggered synchronously with one external flash. This mode allows the K-180A to act as an auxiliary lamp, menawarkan pelbagai kesan cahaya dan bayang-bayang.
6. Penyelenggaraan
- Pembersihan: Use a soft, dry cloth to clean the exterior of the flash unit and accessories. Do not use abrasive cleaners or solvents.
- Storan: Store the kit in a cool, dry place, away from direct sunlight and excessive humidity.
- Penggantian fius: If the unit fails to power on, check the fuse. Replace it with a fuse of the same rating (5A).
7. Penyelesaian masalah
- Denyar tidak menyala:
- Check if the unit is powered on and connected correctly.
- Ensure the RT-16 trigger transmitter and receiver have fresh batteries and are properly synced.
- Verify the sync cord is securely connected to the flash unit.
- Periksa fius.
- Pemodelan lamp tidak bekerja:
- Ensure the Modeling Light Switch is in the ON position.
- Semak sama ada lamp bulb is securely installed and not burnt out.
- Output denyar tidak konsisten:
- Ensure the Flash Output Controller is set correctly.
- Allow sufficient recharging time between flashes.
8. Spesifikasi
8.1. Godox K-180A Flash Unit
| Ciri | Spesifikasi |
|---|---|
| Model | K-180A |
| Output Denyar | 180WS |
| Nombor Panduan (m ISO 100) | 45 |
| Suhu Warna | 5600 ± 200K |
| Kuasa Voltage | AC220/60Hz or 100V/60Hz (Optional, check your unit) |
| Kawalan Kuasa Denyar | Stepless (1/8-full) |
| Pemodelan Lamp | 75WS |
| Masa Pengecasan Semula | 0.5-3 saat |
| Flash Triggering Model | Sync cord, Test button, Slave |
| Tempoh Kilat | 1 / 2000-1 / 800s |
| Fius | 5A |
| Dimensi | 17 x 10 x 17.5cm (approx. 7.2 x 4.1 x 5.4in) |
| Berat badan | Approx. 0.59KG (approx. 603g / 21.3oz) |
8.2. 180cm Light Stand
| Ciri | Spesifikasi |
|---|---|
| Galas Beban | 2kg |
| Ketinggian Teleskopik | 82-200cm |
| Ketinggian Penyimpanan | 68cm |
| Diameter Paip | Φ1.6/1.9/2.2cm |
| Lubang Skru | 1/4" |
| Berat badan | 0.81kg |
| Panjang Berlipat | 67cm |
| Panjang Min | 70cm (2'4") |
| Ketinggian Maksimum | 200cm (7') |
| Ideal Max. Working Height | 140-150cm |
8.3. FS50X70cm Grid Softbox
| Ciri | Spesifikasi |
|---|---|
| Saiz | 50 x 70cm / 20" x 27" |
| Gunung | Gunung Sejagat |
| Berat badan | lebih kurang 0.6kg |
8.4. RT-16 Wireless Flash Trigger
| Ciri | Spesifikasi |
|---|---|
| taip | Pencetus Denyar Tanpa Wayar |
| Saluran | 16 saluran |
| Input Kuasa Pemancar | Bateri 23A 12V (termasuk) |
| Input Kuasa Penerima | 2 * AAA batteries (not included) |
| Receiver Plug Size | 3.5mm |
| Adapter Size for Receiver Plug | 3.5mm & 6.35mm |
| Radio Working Frequency | 433MHz |
| Kelajuan Segerak | 1/200s |
| Outdoor Operation Distance | Hingga 30m (ruang terbuka) |
| Indoor Operation Distance | Hingga 20m (ruang terbuka) |
| Saiz Pakej | 21.5 x 7.5 x 3.8sm / 8.5 x 3.0 x 1.5in |
| Berat Pakej | 125g / 4.4oz |
9. Petua Pengguna
- Penggunaan Fotografi: This kit is primarily intended for photography, providing controlled lighting for studio setups. Experiment with different flash power settings and softbox positions to achieve desired lighting effects.
- Pemodelan Lamp penggunaan: While useful for previewing lighting, remember to give the modeling lamp pecah untuk mengelakkan terlalu panas dan memanjangkan jangka hayatnya.
- Trigger Placement: For optimal wireless triggering, ensure a clear line of sight between the RT-16 transmitter and receiver, especially in indoor environments.
10. Waranti dan Sokongan
For warranty information, technical support, or service inquiries, please contact the seller or the manufacturer directly. Keep your purchase receipt as proof of purchase.