ANDELI MIG-135MINI Multiprocess Welder Instruction Manual

1. Pengenalan

Thank you for choosing the ANDELI MIG-135MINI Multiprocess Welder. This machine is designed for versatility, offering MIG (Flux-Cored), Lift TIG, and MMA (Stick) welding capabilities in a compact and portable unit. This manual provides essential information for the safe and efficient operation, setup, maintenance, and troubleshooting of your welder. Please read this manual thoroughly before operating the machine to ensure proper use and to prevent injury or damage.

Figure 1.1: The ANDELI MIG-135MINI Multiprocess Welder. This image displays the compact design of the welding machine, highlighting its portability and general appearance.

2. Arahan Keselamatan

Welding can be dangerous if proper safety precautions are not observed. Always prioritize safety to prevent electric shock, burns, fire, and other hazards. Read and understand all safety warnings before operating the welder.

2.1 Peralatan Pelindung Diri (PPE)

• Topi keledar kimpalan: Always wear a welding helmet with appropriate shade filter to protect eyes and face from arc rays and sparks.
• Welding Gloves: Use heavy, flame-resistant welding gloves to protect hands from heat, sparks, and electric shock.
• Pakaian Pelindung: Wear flame-resistant clothing, long sleeves, and pants to protect skin from sparks and UV radiation. Avoid synthetic fabrics.
• Safety Footwear: Wear sturdy, closed-toe shoes, preferably leather, to protect feet from falling objects and sparks.

2.2 Keselamatan Elektrik

• Pastikan mesin kimpal dibumikan dengan betul.
• Never operate the welder in wet conditions or damp persekitaran.
• Inspect all cables and connections for damage before each use. Replace damaged components immediately.
• Jangan sentuh bahagian elektrik hidup.

2.3 Pencegahan Kebakaran dan Letupan

• Keluarkan semua bahan mudah terbakar dari kawasan kimpalan.
• Sediakan alat pemadam api.
• Jangan mengimpal pada bekas yang mempunyai bahan mudah terbakar.

2.4 Keselamatan Asap dan Gas

• Ensure adequate ventilation in the welding area to avoid inhaling welding fumes.
• If ventilation is poor, use an approved respirator.

3. Produk Lebihview

Familiarize yourself with the components of your ANDELI MIG-135MINI welder before operation.

3.1 Panel Depan

Figure 3.1: Front Control Panel. This image illustrates the layout of the control panel, including mode selection, current/voltage adjustment knobs, and display screen.

1. Mode Selection Switch: Selects between MIG, Lift TIG, and MMA welding modes.
2. Semasa / VoltagTombol Pelarasan e: Adjusts welding current (MMA/TIG) or voltage (MIG).
3. Wire Speed Adjustment Knob (MIG Mode): Adjusts the speed of the welding wire feed.
4. Paparan Digital: Shows current, voltage, or wire speed settings.
5. Terminal Keluaran: Connections for welding torch, electrode holder, and ground clamp.

3.2 Panel Belakang

• Input Kuasa: Connects to 110V AC power supply.
• Suis kuasa: Menghidupkan/MATI pengimpal.
• Kipas Penyejuk: Provides necessary cooling for internal components.

3.3 Internal Wire Feeder

Figure 3.2: Internal Wire Feeder Assembly. This image shows the mechanism for loading and feeding welding wire, including the wire spool holder and drive rollers.

The welder features an integrated wire feeder for MIG welding, designed for smooth and consistent wire delivery.

4. Persediaan

Proper setup is crucial for safe and effective welding.

4.1 Membongkar dan Pemeriksaan

1. Tanggalkan mesin kimpal dan semua aksesori daripada pembungkusan dengan berhati-hati.
2. Inspect the machine for any signs of shipping damage. If damage is found, contact your dealer immediately.
3. Sahkan bahawa semua komponen yang disenaraikan dalam senarai pembungkusan ada.

4.2 Sambungan Kuasa

• The ANDELI MIG-135MINI operates on a 110V AC power supply.
• Connect the power cord to a dedicated 110V, 20A (minimum) grounded outlet.
• Ensure the power switch on the rear panel is in the "OFF" position before connecting to power.

4.3 Wire Installation (MIG Flux-Cored)

Figure 4.1: Welder Setup Diagram. This diagram illustrates the connections for the welding torch, ground clamp, and power, along with the wire spool installation.

1. Open the wire feeder compartment.
2. Place the 0.030 inch (1kg) flux-cored welding wire spool onto the spool holder. Ensure it rotates freely.
3. Thread the wire through the guide tube and into the drive rollers.
4. Close the drive roller tension arm and adjust the tension. It should be tight enough to feed the wire without slipping, but not so tight as to deform the wire.
5. Ensure the correct drive roller groove (0.030 inch) is aligned with the wire.
6. Feed the wire through the MIG torch liner until it exits the contact tip. You may need to press the torch trigger with the power on (but no arc) to advance the wire.

4.4 Menyambung Aksesori Kimpalan

• Tanah Clamp: Sambungkan tanah clamp cable to the appropriate output terminal on the welder (usually marked with a negative (-) symbol for flux-cored MIG). Secure the clamp ke bahan kerja atau meja kimpalan, memastikan sentuhan elektrik yang baik.
• Obor MIG: Connect the MIG torch cable to the positive (+) output terminal.
• MMA Electrode Holder: For MMA welding, connect the electrode holder cable to the positive (+) terminal and the ground clamp ke terminal negatif (-).
• Angkat Obor TIG: For Lift TIG welding, connect the TIG torch cable to the negative (-) terminal and the ground clamp ke terminal positif (+).

5. Arahan Operasi

This section details the operation of the ANDELI MIG-135MINI in its various welding modes.

5.1 Langkah Operasi Am

1. Ensure all safety precautions are followed and PPE is worn.
2. Connect the welder to power and turn the power switch ON.
3. Select the desired welding mode (MIG, TIG, or MMA) using the mode selection switch.
4. Adjust welding parameters (current, voltage, wire speed) according to the material thickness and welding process.
5. Perform a test weld on scrap material to verify settings.
6. Mulakan kimpalan.

5.2 MIG Welding (Flux-Cored)

• Select "MIG" mode.
• Ensure the welder is set for flux-cored wire (no external gas required).
• Laraskan voltage and wire speed. A good starting point for 0.030 inch flux-cored wire on thin steel is typically 16-18V and 150-200 IPM wire speed. Refer to a welding chart for specific material thicknesses.
• Maintain a consistent stick-out (distance from contact tip to workpiece) of about 3/8 to 1/2 inch (10-13mm).
• Use a drag technique (pulling the torch) for flux-cored welding.

5.3 Angkat Kimpalan TIG

• Select "TIG" mode.
• Connect the TIG torch to the negative (-) terminal and the ground clamp ke terminal positif (+).
• Install a tungsten electrode (e.g., 2% Lanthanated) into the TIG torch.
• Laraskan arus kimpalan.
• To initiate the arc, gently touch the tungsten to the workpiece and then lift it slightly (approx. 1/16 inch or 1.5mm). The arc will start.
• This machine supports Lift TIG, which does not require a high-frequency start unit.

5.4 Kimpalan MMA (Stik).

• Select "MMA" mode.
• Sambungkan pemegang elektrod ke terminal positif (+) dan penutup pembumianamp ke terminal negatif (-).
• Insert the appropriate welding electrode (stick) into the electrode holder.
• Adjust the welding current based on the electrode type and diameter, and the material thickness.
• Strike the arc by lightly scratching the electrode against the workpiece, then quickly lifting it to maintain a short arc length.

6. Penyelenggaraan

Penyelenggaraan tetap memastikan umur panjang dan prestasi optimum pengimpal anda.

6.1 Penyelenggaraan Harian

• Inspect all cables and connections for damage or wear.
• Clean the welding torch nozzle and contact tip (MIG) or collet/collet body (TIG) of spatter.
• Pastikan tanah clamp makes good contact and is free of debris.

6.2 Penyelenggaraan Mingguan/Bulanan

• Clean the wire feeder assembly, removing any dust or wire shavings.
• Check the drive rollers for wear and ensure they are clean.
• Use compressed air to blow dust out of the welder's internal components through the ventilation openings. Ensure the power is disconnected before doing this.
• Periksa kord kuasa untuk sebarang kerosakan.

Nota: For any internal repairs or complex maintenance, contact qualified service personnel. Do not attempt to repair the machine yourself if you are not trained.

7. Penyelesaian masalah

Bahagian ini menyediakan penyelesaian kepada isu operasi biasa. Untuk masalah yang tidak disenaraikan di sini, hubungi khidmat pelanggan.

8. Spesifikasi

Technical specifications for the ANDELI MIG-135MINI Multiprocess Welder.

9. Waranti dan Sokongan

ANDELI products are manufactured to high-quality standards. For warranty information, technical support, or service inquiries, please contact your authorized dealer or the ANDELI customer service department. Keep your purchase receipt as proof of purchase for warranty claims.

Contact information can typically be found on the ANDELI official webtapak atau melalui tempat pembelian anda.