RAYZEEK RZ020 Motion Sensor Light Switch User Manual

1. Produk Lebihview

The RAYZEEK RZ020 Motion Sensor Light Switch is designed to automate your lighting based on motion detection. It offers versatile 3-in-1 sensor modes: Occupancy, Vacancy, and Manual ON/OFF. This switch is suitable for various indoor applications and is UL Listed for safety.

Figure 1: RAYZEEK PIR Motion Sensor Switch Overview

2. Maklumat Keselamatan

WARNING: To avoid fire, shock, or death, turn OFF power at the circuit breaker or fuse box and test that the power is OFF before wiring. Installation should be performed by a qualified electrician if you are not familiar with electrical wiring.

• This device requires an effective Ground Wire. The device will not function if it is not grounded or the ground wire does not work.
• No Neutral Wire is required.
• Single Pole Indoor Use Only. Not suitable for 3-way circuits.
• Ensure all wire connections are secure and insulated.

3. Kandungan Pakej

• RAYZEEK RZ020 Motion Sensor Light Switch
• Plat Dinding
• Skru Pemasangan
• Kacang Kawat
• Manual Pengguna

4. Arahan Pemasangan

1. Matikan Kuasa: Locate your circuit breaker or fuse box and turn off the power to the switch location. Verify power is off using a voltage penguji.
2. Keluarkan Suis Lama: Carefully remove the existing wall plate and light switch. Disconnect the wires from the old switch.
3. Kenal pasti wayar: Gunakan voltage tester to identify the Hot wire (Line), Load wire, and Ground wire. Label them for easy identification.
4. Sambungkan Suis Baharu: Connect the wires from the RZ020 switch to your household wiring using the provided wire nuts:
   • Black wire from RZ020 to the Hot wire (Line)
   • Red wire from RZ020 to the Load wire
   • Green wire from RZ020 to the Ground wire
   

   Figure 2: Wiring Directions - Connect Hot, Load, and Ground wires. Neutral wire is not required.

5. Suis Pemasangan: Gently push all connected wires back into the wall box, ensuring no wires are exposed. Secure the RZ020 switch into the wall box using the provided screws.
6. Pasang Plat Dinding: Attach the decorative wall plate over the switch. Ensure the side marked 'UP' is facing upwards.
7. Pulihkan Kuasa: Turn the power back ON at the circuit breaker. The green indicator light on the RZ020 will flash, indicating it is warming up and functioning.

5. Mod Operasi

The RZ020 offers three versatile operating modes: Occupancy, Vacancy, and Manual ON/OFF. The default setting after connection is Occupancy mode with a 1-minute time delay and 25 Lux ambient light sensor value.

Gambar 3: Lebihview of 3-in-1 Operation Modes

5.1. Occupancy Sensor Mode (Auto ON & Auto OFF)

In this mode, the light automatically turns ON when motion is detected and automatically turns OFF after a set time delay when no motion is detected. This mode is ideal for high-traffic areas where hands-free operation is desired.

5.2. Vacancy Sensor Mode (Manual ON & Auto OFF)

In Vacancy mode, the light must be manually turned ON by pressing the main button. It will then automatically turn OFF after a set time delay when no motion is detected. This mode is suitable for areas where you prefer to control when the light comes on, but still want the convenience of automatic shut-off.

5.3. Manual ON/OFF Mode

In Manual mode, the switch functions like a traditional light switch. The light is turned ON or OFF by pressing the small button. Motion detection is still active (red indicator flashes), but it will not trigger the light to turn ON or OFF. This mode is useful when you need the light to stay on indefinitely or prefer full manual control.

6. Penetapan Pelarasan

The RZ020 allows for easy adjustment of its operating mode, time delay, and sensitivity without removing the wall plate.

Figure 4: Easy Adjust Mode and Setting Overview

6.1. Adjusting Operation Mode

To change the operation mode (Vacancy, Occupancy, Occupancy without light sensor):

1. Tekan dan tahan butang small button for more than 4 seconds. The LED indicator will flash.
2. The number of flashes indicates the current mode:
• 1 flash: Vacancy mode
• 2 flashes: Occupancy mode
• 3 flashes: Occupancy without light sensor mode
3. Release the button after the desired number of flashes.

6.2. Adjusting Time Delay

To change the time delay for automatic shut-off:

1. Tekan dan tahan butang butang besar for more than 4 seconds. The LED indicator will flash.
2. The number of flashes indicates the time delay setting:
• 1 flash: 15 seconds
• 2 flashes: 1 minute
• 3 flashes: 3 minutes
• 4 flashes: 5 minutes
• 5 flashes: 15 minutes
• 6 flashes: 30 minutes
3. Release the button after the desired number of flashes.

6.3. Adjusting Sensitivity and Ambient Light Sensor

To adjust the motion sensitivity or ambient light sensor value:

1. Tekan dan tahan both the big and small buttons simultaneously for more than 4 seconds. The LED indicator will flash.
2. The number of flashes indicates the setting:
• 1 flash: Low sensitivity
• 2 flashes: High sensitivity (Default)
• 3 flashes: Light sensor 15 Lux
• 4 flashes: Light sensor 25 Lux (Default)
• 5 flashes: Light sensor 35 Lux
• 6 flashes: Restore to factory settings
3. Release the buttons after the desired number of flashes.

Figure 5: Ambient Light Sensor Functionality - Light stays off if bright, turns on if dark (based on Lux setting).

7. Spesifikasi

Rajah 6: Spesifikasi Produk Terperinci

Figure 7: Item Dimensions

8. Penyelesaian masalah

• Lampu tidak menyala:
  • Ensure power is ON at the circuit breaker.
  • Sahkan semua sambungan pendawaian selamat.
  • Check if the ground wire is effectively connected.
  • Confirm the ambient light sensor setting is not preventing the light from turning on (e.g., if set to stay OFF when bright).
  • Check the sensitivity setting; increase if motion is not being detected.
• Light does not turn OFF:
  • Pastikan tiada gerakan berterusan dalam julat pengesanan sensor.
  • Check the time delay setting; it might be set to a longer duration.
  • If in Manual ON/OFF mode, the light will not turn off automatically.
• Sensor is too sensitive/not sensitive enough:
  • Adjust the sensitivity setting as described in Section 6.3.
  • Pastikan kanta penderia bersih dan tidak terhalang.
• Light turns ON/OFF randomly:
  • Check for drafts, heat sources, or small pets that might be triggering the sensor.
  • Adjust the sensitivity setting to a lower level.

9. Waranti dan Sokongan

The RAYZEEK RZ020 Motion Sensor Light Switch comes with a Waranti 1 Tahun from the date of purchase. If you encounter any issues or require technical assistance, please contact RAYZEEK customer support.