Kit Kawalan Jauh Pendiang Gas DIGITEN Manual Pengguna WTC401

1. Pengenalan

This manual provides detailed instructions for the installation, operation, and maintenance of your DIGITEN Gas Fireplace Remote Control Kit, Model WTC401. This kit is designed to provide wireless control for millivolt valve gas fireplaces, offering ON/OFF, automatic thermostat, and timer functions for enhanced convenience and comfort.

2. Maklumat Keselamatan

Please read all safety warnings and instructions carefully before installation and operation to prevent injury or property damage.

Voltage Had: Do not use this remote-control system on applications with voltagadalah melebihi 24 Volt AC/DC dan 1 amp current. Exceeding these limits can damage the unit and pose a safety hazard.
Pendedahan Haba: The receiver unit must be installed away from high heat sources (above 130°F / 54°C) to ensure proper function and prevent damage.
Pemadaman Manual: For extended absences from home, it is recommended to manually turn off the fireplace at the gas valve for maximum safety.
Pemasangan Profesional: If you are unsure about any part of the installation process, consult a qualified technician.
Keselamatan Bateri: Always use the specified battery types and ensure correct polarity. Do not mix old and new batteries or different battery types. Dispose of used batteries responsibly.

3. Kandungan Pakej

Sahkan bahawa semua komponen yang disenaraikan di bawah disertakan dalam pakej anda:

DIGITEN Gas Fireplace Remote Control Kit components including remote, receiver, wall plate, wires, and screws.

Figure 3.1: Contents of the DIGITEN Gas Fireplace Remote Control Kit.

Alat Kawalan Jauh (Pemancar)
Kotak Penerima
Wall Plate for Receiver
Wayar Sambungan
Skru Pemasangan

4. Produk Lebihview

4.1 Remote Control (Transmitter)

The remote control features a large, backlit LCD screen for clear display of current room temperature, desired set temperature, operating mode, and timer status. It operates wirelessly with a signal range of up to 65 feet (20 meters).

Close-up of the remote control LCD screen with labels pointing to current room temperature, desired set temperature, temperature unit, safety lock indicator, timer, operation modes, and battery low indicator.

Figure 4.1: Remote Control LCD Display and Button Functions.

Paparan LCD: Shows current room temperature, set temperature, temperature unit (°F/°C), timer, safety lock status, and battery low indicator.
Butang MOD: Cycles through ON, AUTO, and OFF operating modes.
Butang PEMASA: Activates and adjusts the timer function.
Anak panah atas/bawah: Adjusts set temperature and timer values.
Sensor terbina dalam: The remote control contains the temperature sensor for thermostat operation.

4.2 Penerima

The receiver unit acts as a wireless switch for your fireplace. It connects directly to the millivolt valve and receives commands from the remote control. It features a manual ON/AUTO/OFF switch and a 'LEARN' button for pairing.

The DIGITEN remote control kit showing the white wall plate, black receiver box, and white remote control, along with connection wires and screws.

Figure 4.2: Receiver Box and Wall Plate.

ON/AUTO/OFF Switch: Allows manual control of the fireplace directly from the receiver.
Butang BELAJAR: Used to establish communication between the remote and receiver.
Petak Bateri: Houses 4 AA batteries for power.

5. Persediaan dan Pemasangan

5.1 Pemasangan Bateri

Batteries are not included in the kit and must be purchased separately.

Image showing the battery compartments for the receiver (4 AA batteries) and the remote control (2 AAA batteries).

Figure 5.1: Battery requirements for the remote and receiver.

Kawalan Jauh: Requires 2 AAA batteries. Open the battery compartment on the back of the remote and insert the batteries, observing correct polarity.
Penerima: Requires 4 AA batteries. Open the battery compartment on the receiver box and insert the batteries, observing correct polarity.

5.2 Receiver Wiring to Millivolt Valve

This system is designed for millivolt gas valve systems. It functions as an on/off switch and connects to the TH and TH/TP terminals of your millivolt valve.

Diagram showing how to connect the receiver wires to the TH and TH/TP terminals of a gas fireplace millivolt valve.

Figure 5.2: Connecting the receiver to the millivolt gas valve.

Ensure the gas supply to the fireplace is turned off before beginning installation.
Locate the millivolt valve on your gas fireplace. Identify the TH and TH/TP terminals.
Connect the two wires from the receiver to the TH and TH/TP terminals of the millivolt valve. The connection is non-polarized, so the order of the wires does not matter.
Mount the receiver box in a suitable location, either inside the fireplace control area or on a wall using the provided wall plate and screws. Ensure it is away from direct heat.
Restore the gas supply to the fireplace.

Detailed diagram of a millivolt gas valve showing the TH, TP, and TH/TP terminals, and the thermopile/pilot light connection.

Figure 5.3: Millivolt Gas Valve Terminals.

5.3 Memasang Alat Kawalan Jauh dan Penerima

After installing batteries and wiring the receiver, you need to pair the remote control with the receiver.

On the receiver unit, slide the switch to the 'ON' or 'AUTO' position.
Press and hold the 'LEARN' button on the receiver until you hear a beep or see an indicator light flash (refer to receiver for specific indicator).
Within 10 seconds, press any button on the remote control. The receiver will beep again or the light will stop flashing, indicating successful pairing.
Test the connection by pressing the ON/OFF buttons on the remote. The fireplace should respond.

6. Arahan Operasi

6.1 Hidupkan/Mati Kuasa

Untuk Menghidupkan: Press the 'MODE' button on the remote until 'ON' is displayed, or press the 'Up' arrow button.
Untuk Mematikan: Press the 'MODE' button on the remote until 'OFF' is displayed, or press the 'Down' arrow button.

6.2 Pemilihan Mod

Press the 'MODE' button on the remote to cycle through the following operating modes:

Mod HIDUP: The fireplace will remain continuously on until manually turned off.
Mod MATI: The fireplace will remain continuously off.
AUTO Mode (Thermostat): The fireplace will turn on and off automatically to maintain the desired set temperature. The remote's built-in sensor measures the room temperature.

6.3 Thermostat Function (AUTO Mode)

Image showing the remote control with a callout indicating that the temperature sensor is built into the remote control itself.

Figure 6.1: The remote control houses the temperature sensor.

In AUTO mode, use the 'Up' and 'Down' arrow buttons to set your desired temperature. The remote will display both the current room temperature and the set temperature.
To switch between Fahrenheit (°F) and Celsius (°C), refer to the remote control's specific instructions (usually a combination button press or a switch in the battery compartment).
The fireplace will activate when the room temperature drops below the set temperature and deactivate when it reaches or exceeds the set temperature.

6.4 Fungsi Pemasa

Press the 'TIMER' button to activate the timer.
Use the 'Up' and 'Down' arrow buttons to set the desired duration for the fireplace to operate (e.g., 30 minutes, 1 hour).
The fireplace will automatically turn off once the set time has elapsed.

6.5 Kunci Keselamatan Kanak-kanak

The child safety lock prevents accidental activation of the fireplace.

Image illustrating the childproof lock feature, showing a hand reaching for the remote and text indicating to press and hold UP & TIMER simultaneously to unlock and lock.

Figure 6.2: Activating the Child Safety Lock.

Untuk mengunci: Press and hold the 'Up' arrow button and the 'TIMER' button simultaneously for a few seconds until a lock icon appears on the LCD screen.
Untuk Membuka Kunci: Press and hold the 'Up' arrow button and the 'TIMER' button simultaneously again until the lock icon disappears.

7. Penyelenggaraan

7.1 Penggantian Bateri

When the battery low indicator appears on the remote control's LCD screen, replace the batteries within two weeks to ensure continuous operation.

Kawalan Jauh: Gantikan dengan 2 bateri AAA baharu.
Penerima: Gantikan dengan 4 bateri AA baharu.
Always use fresh, high-quality alkaline batteries.

8. Penyelesaian masalah

Masalah	Kemungkinan Punca	Penyelesaian
Fireplace does not respond to remote control.	Low batteries in remote or receiver. Remote and receiver not paired. Receiver switch in 'OFF' position. Jauh di luar julat.	Gantikan bateri di kedua-dua unit. Re-pair the remote and receiver (Section 5.3). Slide receiver switch to 'ON' or 'AUTO'. Move closer to the receiver (within 65 feet).
Fireplace turns on/off unexpectedly in AUTO mode.	Temperature sensor (in remote) affected by drafts or heat sources. Large temperature hysteresis (5°F/3°C).	Relocate the remote control to an area with stable ambient temperature, away from direct heat or cold drafts. Note that the system has a built-in 5°F (3°C) temperature differential before activating/deactivating. This is normal operation.
Paparan LCD malap atau kosong.	Bateri lemah dalam jarak jauh.	Gantikan bateri kawalan jauh.
Kunci keselamatan kanak-kanak tidak boleh ditanggalkan.	Incorrect button combination or duration.	Ensure you are pressing and holding the 'Up' arrow and 'TIMER' buttons simultaneously for several seconds.
Penerima tidak dapat dihidupkan.	Low or incorrectly installed batteries.	Periksa kekutuban bateri dan gantikan dengan bateri AA yang baru.

9. Spesifikasi

Diagram showing the dimensions of the remote control, receiver box, and wall cover in both centimeters and inches.

Rajah 9.1: Dimensi Produk.

Ciri	Perincian
Nombor Model	WTC401
Dimensi Produk	1.73 x 0.98 x 4.37 inches (Remote)
Berat Barang	8.6 ounces (Total Kit)
Power Supply (Remote)	2 x bateri AAA (tidak termasuk)
Bekalan Kuasa (Penerima)	4 x bateri AA (tidak termasuk)
Keserasian	Millivolt valve gas fireplaces
Vol. Makstage / Semasa	24 Volts AC/DC, 1 Amp
Julat Tanpa Wayar	Sehingga 65 kaki (20 meter)
Ciri Khas	Backlit LCD, Digital Display, Thermostat, Timer, Child Safety Lock

10. Waranti dan Sokongan

DIGITEN provides a one-year warranty for any product quality problems. If you encounter any issues or require assistance, please contact DIGITEN customer support through the retailer where the product was purchased or visit the official DIGITEN webtapak untuk maklumat hubungan sokongan.

We are committed to providing reliable products and personalized service to ensure your satisfaction.

DIGITEN WTC401