Whubefy Heat Press 12x15 inch 5-in-1 Combo Instruction Manual

1. Arahan Keselamatan

Read all instructions before using the heat press machine. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• Always operate the machine on a stable, heat-resistant surface.
• Keep hands and fingers clear of the heating platen during operation to prevent burns.
• Pastikan pengudaraan yang betul di kawasan kerja.
• Do not leave the machine unattended while it is powered on or heating.
• Cabut plag mesin daripada soket kuasa apabila tidak digunakan atau sebelum pembersihan/penyelenggaraan.
• Do not use the machine near water or in damp syarat.
• Jauhkan kanak-kanak dan haiwan peliharaan dari mesin.
• Use only the provided power cord and ensure it is not damaged.
• The machine features an intelligent 30-minute auto-standby system and built-in safety sensors to prevent overheating.

2. Kandungan Pakej

Sahkan bahawa semua komponen terdapat dalam pakej:

• 1 x 12"x15" Heat Press Machine (Main Unit)
• 1 x 11oz Tumbler Press Machine Attachment
• 1 x 5.5"x3" Hat Press Attachment
• 1 x 5" Plate Press Attachment
• 1 x 6" Plate Press Attachment
• 3 x DTF Transfer Paper with Design
• 1 x Sublimation Paper with Design
• 1 x Blank T-shirt
• 1 x Transfer Tape
• 1 x Detailed Manual (This document)
• Necessary tools for assembly (e.g., wrench)

3. Persediaan

3.1 Membongkar dan Pemeriksaan Awal

1. Keluarkan semua komponen dari pembungkusan dengan berhati-hati.
2. Inspect the machine and all attachments for any signs of damage during transit. Contact customer support if any damage is found.
3. Place the main heat press unit on a sturdy, level, and heat-resistant workbench.

3.2 Assembling Attachments

The main heat press platen is pre-assembled. Other attachments (mug, hat, plate presses) need to be attached as required. Refer to the specific attachment's instructions for detailed assembly.

• Hat Press: Secure the hat press attachment to the designated mounting point on the main unit using the provided screws and tools.
• Tumbler/Mug Press: Connect the tumbler/mug press unit to the main control box via its dedicated port. Ensure a secure connection.
• Penekan Plat: Attach the desired plate press (5" or 6") to the main unit's platen attachment point.

3.3 Sambungan Kuasa

1. Pastikan suis kuasa mesin berada dalam kedudukan "OFF".
2. Palamkan kord kuasa ke salur keluar AC 110V yang dibumikan.
3. Turn the main power switch to "ON". The digital display will illuminate.

4. Arahan Operasi

4.1 Panel Kawalan Digital Selesaiview

The control panel allows precise adjustment of temperature and time.

• Temperature/Time Keys (+/-): Use to increase or decrease temperature and time values.
• Kunci SET: Press to cycle between temperature and time settings. Hold for 5 seconds for precision calibration.
• Kunci Mula: Initiates the countdown timer once the set temperature is reached.
• Penukaran Unit Suhu: Press the "+" and "-" buttons simultaneously for 3 seconds to switch between Celsius (°C) and Fahrenheit (°F).

4.2 Menetapkan Suhu dan Masa

1. Tekan ke SET button once. The temperature display will flash.
2. Gunakan + dan - buttons to adjust the desired temperature (range: 32-450°F / 0-232°C).
3. Tekan ke SET button again. The time display will flash.
4. Gunakan + dan - buttons to adjust the desired time (range: 0-999 seconds).
5. Tekan SET a third time to confirm settings and exit the setting mode. The machine will begin heating to the set temperature.

4.3 Melaraskan Tekanan

The adjustable pressure knob allows you to customize pressure based on the material thickness and transfer type.

• Turn the pressure adjustment knob clockwise to increase pressure.
• Turn the pressure adjustment knob counter-clockwise to decrease pressure.
• Test pressure on a scrap material if unsure.

4.4 General Transfer Process (Main Platen)

1. Sediakan Mesin: Ensure the main platen is attached. Set the desired temperature and time. Allow the machine to reach the set temperature (it will beep when ready).
2. Prepare the Item: Place the garment or flat item on the silicone mat on the lower platen. Ensure it is flat and wrinkle-free.
3. Position Transfer: Place your transfer design (e.g., HTV, sublimation paper) onto the item, ensuring it is correctly aligned. Use transfer tape if necessary.
4. Kenakan Tekanan: Swing the heating platen over the item. Lower the handle firmly to apply pressure. The timer will start automatically.
5. Complete Transfer: Once the timer counts down and the alarm sounds, lift the handle and swing the heating platen away.
6. Alih Keluar Item: Carefully remove the transferred item. Follow specific peeling instructions for your transfer material (hot peel, warm peel, cold peel).

4.5 Using Specific Attachments

Each attachment requires specific handling and may have different temperature/time recommendations. Always refer to the transfer material manufacturer's guidelines.

• Tumbler/Mug Press:
  • Attach the tumbler press to the main unit.
  • Wrap your sublimation design tightly around the tumbler/mug and secure with heat-resistant tape.
  • Insert the tumbler/mug into the press. Adjust pressure so it's snug but not overly tight.
  • Close the press and start the timer. Rotate the tumbler/mug halfway through the pressing time for even heat distribution if necessary.
• Hat Press:
  • Attach the hat press platen.
  • Place the hat onto the curved platen, ensuring the area to be pressed is flat.
  • Position the transfer design.
  • Lower the heating element and apply pressure.
• Tekan Plat:
  • Select and attach the appropriate size plate press (5" or 6").
  • Place the plate onto the lower platen.
  • Position the transfer design on the plate.
  • Lower the heating element and apply pressure.

5. Penyelenggaraan

Penyelenggaraan yang kerap memastikan jangka hayat dan prestasi optimum mesin tekan haba anda.

• Cleaning the Heating Platen:
  • Ensure the machine is unplugged and completely cool before cleaning.
  • Wipe the Teflon-coated heating platen with a soft, damp cloth. For stubborn residue, use a non-abrasive cleaner specifically designed for non-stick surfaces.
  • Do not use abrasive pads or harsh chemicals, as this can damage the Teflon coating.
• Cleaning the Silicone Mat:
  • Remove the silicone mat from the lower platen.
  • Wash with mild soap and water. Rinse thoroughly and allow to air dry completely before re-placing.
• Pembersihan Am:
  • Lap bahagian luar mesin dengan kain lembut dan kering.
  • Keep the control panel free of dust and debris.
• Storan: Simpan mesin dalam persekitaran yang bersih dan kering apabila tidak digunakan.

6. Penyelesaian masalah

7. Spesifikasi

8. Waranti & Sokongan

8.1 Maklumat Waranti

Whubefy products are manufactured to high-quality standards. Specific warranty details may vary. Please retain your proof of purchase for warranty claims.

For information regarding product protection plans, please refer to the purchase platform or contact customer support.

8.2 Sokongan Pelanggan

If you encounter any issues, have questions about operation, or require technical assistance, please contact Whubefy customer support.

Contact information can typically be found on the Whubefy official webtapak atau melalui peruncit tempat produk itu dibeli.

When contacting support, please provide your product model number (Heat Press) and a detailed description of the issue.